Home › Drivetrain › EG62F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE SYSTEM
NM3620E _52 Drivetrain _076464 EG62F MANUAL TRANSMISSION / TRANSAXLE _0377815 MANUAL TRANSAXLE SYSTEM CO CONTROL F

EG62F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  CONTROL  GEAR SHIFT INDICATOR SYSTEM  


FUNCTION OF MAIN COMPONENTS


Component Function
Crank Position Sensor Detects the engine speed and performs cylinder identification.
Accelerator Pedal Sensor Assembly Detects the amount of pedal effort applied to the accelerator pedal.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Back-up Light Switch Assembly Detects that the transaxle is in the reverse shift condition.
Clutch Pedal Stroke Sensor Assembly Detects the amount of pedal effort applied to the clutch pedal.
Speed Sensor Detects the wheel speed.
ECM Controls the engine speed based on signals from each sensor and switch.
Combination Meter Assembly Gear Shift Indicator Displays the Gear Shift Indicator when upshifting or downshifting is recommended.
Brake Actuator Assembly Skid Control ECU Transmits the wheel speed signal to the ECM.


FUNCTION


a.

In the Gear Shift Indicator system, the ECM calculates an environmentally favorable shift position based on the vehicle conditions, and makes a request to the meter ECU to indicate upshifting or downshifting. Then, the Gear Shift Indicator in the combination meter gives a shifting recommendation to the driver.


b.

The ECM determines the actual gear position based on the signals from the crank position sensor and speed sensors, and the target gear position based on the signals from the accelerator pedal position sensor and speed sensors.


c.

By driving in accordance with the shift change recommendations indicated by the Gear Shift Indicator, the driver can enhance environmental performance, improve fuel economy and reduce exhaust gas output within the limits of engine performance.

Control of Gear Shift Indicator System
Control Outline
Shifting Recommendation Control Calculates an environmentally favorable shift position based on the driving conditions of the vehicle, and gives a shifting recommendation.
Shift Control in Uphill Traveling Prevents unnecessary shifting instructions by estimating the gradient of the road based on the driving conditions, and provides shift position instructions that enable the vehicle to attain the proper drive force.
Delta Throttle Acceleration Control Detects a deceleration request when the driver releases the accelerator pedal suddenly. As a result, this control will not provide an upshift instruction. However, it will provide an upshift recommendation to protect the engine if the engine speed is high.


d.

The Gear Shift Indicator system will not perform control while the vehicle is being driven in reverse.


e.

The Gear Shift Indicator system will not perform control while the vehicle is stopped or the clutch is not engaged while shifting.


f.

Upon receiving a shift instruction request from the ECM, the meter ECU will illuminate the indicator light.

X142469E03
1.573,1.083 1.875,1.083 true 1.573,1.698 1.875,1.698 true 0.948,2.188 2.25,2.49 1.302,0.302 10 false Gear Shift Indicator 3.042,0.833 4.354,1.135 1.313,0.302 10 false Illumination Location 4.823,0.833 6.333,1.135 1.51,0.302 10 false Instruction Description 3.594,1.271 3.906,1.573 0.313,0.302 10 false A 3.594,1.698 3.906,2 0.313,0.302 10 false B 4.74,1.281 6.438,1.563 1.698,0.281 10 false Shift-up Recommendation 4.708,1.698 6.563,1.948 1.854,0.25 10 false Shift-down Recommendation 1.927,1 2.24,1.302 0.313,0.302 10 false A 1.927,1.615 2.24,1.917 0.313,0.302 10 false B