Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Gasoline Model)
NM3620E _54 Brake _076467 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379042 BRAKE CONTROL SYSTEM(for Gasoline Model) GE GENERAL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Gasoline Model)  GENERAL  GENERAL  


OUTLINE


a.

The following brake control functions are provided: Anti-lock Brake System (ABS), Electronic Brake force Distribution (EBD), brake assist, Traction Control (TRC), Vehicle Stability Control (VSC), Active Cornering Assist (ACA), steering cooperative control, trailer sway control, hill-start assist control, downhill assist control* and brake hold.

*: Models with downhill assist control



b.

The skid control ECU processes signals from sensors and performs brake control.


c.

An emergency brake signal system is used. This system reduces the danger of rear-end collisions by automatically flashing the hazard warning lights during emergency braking to warn vehicles to the rear.*

*: Except destination package for Korea



d.

A secondary collision brake system is used. This system lessens damage from a secondary collision by controlling the automatic brakes and stop light illumination after a collision occurs.*

*: Models with pre-collision system



e.

The skid control ECU performs brake control from various driving support systems. For details, refer to each driving support system.


f.

Multi-terrain select is used. When the driver performs a switch operation to select an appropriate mode for the road conditions, vehicle control switches to the optimal control for the road conditions. As a result, optimal driving performance is maintained, achieving superior off-road driveability.*

*: 4WD/AWD models




PRECAUTION


a.

ABS

i.

The ABS system cannot increase the performance limit of the tires. Always drive safely and be aware of the vehicle speed and distance to other vehicles.


ii.

Any non-standard components such as non-standard tires that are installed may have a negative effect on the ABS function.


iii.

When braking using ABS, the braking distance may be longer than models without ABS in the following conditions:

·

When driving on a dirt road or a road covered with fresh snow

·

When using tire chains

·

When driving over a joint in the road surface

·

When driving on a rough road such as an unpaved or stone-paved road




b.

Brake Assist

i.

Brake assist cannot increase the performance limit of the fundamental brake system. Always drive safely and be aware of the vehicle speed and distance to other vehicles.



c.

TRC, VSC

i.

The TRC and VSC systems ensure traction and vehicle stability. Do not disable the TRC and VSC functions unless necessary.


ii.

The TRC and VSC systems cannot increase the performance limit of the tires. Always drive the vehicle carefully in conditions in which drive wheel traction or vehicle stability may be lost.



d.

Active Cornering Assist (ACA)

i.

Active Cornering Assist (ACA) cannot increase the performance limit or innate maneuverability of the vehicle itself.


ii.

Do not overly rely on Active Cornering Assist (ACA). Active Cornering Assist (ACA) may not operate effectively when accelerating down slopes or driving on slippery road surfaces.


iii.

When Active Cornering Assist (ACA) frequently operates, Active Cornering Assist (ACA) may temporarily stop operating to ensure proper operation of the brakes, TRC and VSC.



e.

Hill-start Assist Control

i.

Hill-start assist control is not intended to keep the vehicle stationary on a hill for a prolonged period. As hill-start assist control only prevents the vehicle from rolling backwards for 2 seconds after the brake pedal is released, perform start-off within this period.


ii.

When hill-start assist control is operating and the ignition switch is turned off, hill-start assist control will be canceled without warning.


iii.

Hill-start assist control prevents the vehicle from rolling backwards by controlling the brake force to the 4 wheels. However, the vehicle may not remain stationary when on an extremely steep slope or a low friction surface such as ice.



f.

Downhill Assist Control

i.

Check that the downhill assist control indicator light is illuminated before driving. While downhill assist control is operating, the slip indicator light in the combination meter blinks or the brake lights illuminate.


ii.

When downhill assist control consecutively operates, the temperature inside the brake actuator increases and downhill assist control may be temporarily canceled.


iii.

At this time, a buzzer in the combination meter assembly sounds and the downhill assist control indicator light blinks to inform the driver that downhill assist control is canceled. When the temperature inside the brake actuator decreases and the downhill assist control indicator returns to the illuminated condition, control via downhill assist control is possible.


iv.

On extremely steep slopes and extremely slippery surfaces such as snow-covered roads, it may not be possible to maintain a set vehicle speed.



g.

Brake Hold

i.

The brake hold is not for parking the vehicle for a long period of time in the same way as the parking brake.


ii.

If brake hold control does not operate even when the vehicle stops, depress the brake pedal again firmly to stop the vehicle. If the vehicle still does not stop, confirm the conditions for brake hold control to operate.


iii.

When the ignition switch is turned off during brake hold operation, control stops.


iv.

This function may not stop the vehicle on steep slopes and slippery roads.



h.

Multi-terrain Select

i.

Multi-terrain select is not intended to expand the limits of the vehicle. Thoroughly check the road conditions and drive with caution.


ii.

The recommended mode selected by multi-terrain select is only a recommendation. The recommended mode may not be the most appropriate depending on the road conditions (pitch, slipperiness and undulations). Thoroughly check the road conditions before driving.


iii.

Multi-terrain select controls the vehicle so that the motive force can be maximized to improve off-road driveability. Therefore, the fuel economy will not be as efficient as when driving without multi-terrain select.


iv.

Only use multi-terrain select during off-road driving, and use normal mode at all other times.



i.

Ignition Switch Expressions

i.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section:

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch Off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)