Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Gasoline Model)
NM3620E _54 Brake _076467 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379042 BRAKE CONTROL SYSTEM(for Gasoline Model) DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Gasoline Model)  DETAILS  BRAKE ACTUATOR  


CONSTRUCTION


a.

The brake actuator assembly consists of the brake actuator portion and skid control ECU.

X142106C01
2.563,1.688 1.688,1.146 true 5.479,2 4.604,1.458 true 1.5,1.031 1.813,1.188 0.313,0.156 10 false *a 5.521,1.99 5.833,2.146 0.313,0.156 10 false *1
*1 Skid Control ECU - -
*a Brake Actuator Portion - -



b.

The brake actuator portion consists of 2 master cylinder cut solenoid valves, 2 reservoir cut solenoid valve, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs and a master cylinder pressure sensor.

Brake Fluid Hydraulic Circuit Diagram
X112342C01
3.26,5.229 3.438,5.354 3.438,5.354 3.438,6.042 true 3.99,5.24 3.813,5.365 3.813,5.365 3.813,6.052 true 3.365,7.125 3.365,6.604 true 3.896,7.115 3.896,6.594 true 3.552,0.49 3.865,0.646 0.313,0.156 10 *1 0.688,1.49 1,1.646 0.313,0.156 10 *2 5.542,1.771 5.854,1.927 0.313,0.156 10 *3 1.281,3.323 1.594,3.479 0.313,0.156 10 *4 2.583,3.313 2.896,3.469 0.313,0.156 10 *5 1.552,4.823 1.865,4.979 0.313,0.156 10 *6 1.542,6 1.854,6.156 0.313,0.156 10 *7 3.396,6.073 3.708,6.229 0.313,0.156 10 *8 3.292,7.146 3.604,7.302 0.313,0.156 10 *9 1.469,7.302 1.938,7.458 0.469,0.156 10 *10 2.469,7.292 2.938,7.448 0.469,0.156 10 *11 4.583,7.271 5.052,7.427 0.469,0.156 10 *12 5.594,7.271 6.063,7.427 0.469,0.156 10 *13 4.51,3.323 4.823,3.479 0.313,0.156 10 *5 5.854,3.313 6.167,3.469 0.313,0.156 10 *4 2.448,4.813 2.76,4.969 0.313,0.156 10 *6 4.646,4.813 4.958,4.969 0.313,0.156 10 *6 5.563,4.813 5.875,4.969 0.313,0.156 10 *6 2.438,6 2.75,6.156 0.313,0.156 10 *7 4.646,6 4.958,6.156 0.313,0.156 10 *7 5.573,6 5.885,6.156 0.313,0.156 10 *7 3.76,6.083 4.073,6.24 0.313,0.156 10 *8 3.833,7.135 4.146,7.292 0.313,0.156 10 *9
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pump
*9 Reservoir *10 Front Brake Caliper (Right Side)
*11 Rear Brake Caliper (Left Side) *12 Rear Brake Caliper (Right Side)
*13 Front Brake Caliper (Left Side) - -




OPERATION


a.

ABS and EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator assembly in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.

X110377C03
0.417,0.219 2.563,4.51 2.146,4.292 2.74,0.219 4.771,4.51 2.031,4.292 4.865,0.219 6.938,4.51 2.073,4.292 1.583,1.573 1.729,0.74 1.729,0.74 1.938,0.74 true 0.729,2.979 0.948,2.979 0.948,2.979 1.344,3.292 true 2.01,0.677 2.323,0.833 0.313,0.156 10 *1 0.563,2.927 0.875,3.083 0.313,0.156 10 *2 1.417,2.354 1.729,2.51 0.313,0.156 10 *3 1.427,4.031 1.74,4.188 0.313,0.156 10 *4 0.521,0.281 0.833,0.438 0.313,0.156 10 *a 2.854,0.292 3.167,0.448 0.313,0.156 10 *b 4.99,0.292 5.302,0.448 0.313,0.156 10 *c 2.115,4.25 2.427,4.406 0.313,0.156 10 *d 4.927,2.771 5.24,2.927 0.313,0.156 10 *e 3.625,2.354 3.938,2.552 0.313,0.198 10 *3 5.771,2.344 6.083,2.542 0.313,0.198 10 *3 3.646,4.031 3.958,4.229 0.313,0.198 10 *4 5.771,4.021 6.083,4.219 0.313,0.198 10 *4 6.51,4.198 6.823,4.354 0.313,0.156 10 *f
*1 Port A *2 Port B
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a Increase Mode *b Holding Mode
*c Reduction Mode *d to Wheel Cylinder
*e to Reservoir and Pump *f from Wheel Cylinder


ABS and EBD Control Operation
Not Activated Normal Braking - -
Activated Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve (Port A) Off (Open) On (Close) On (Close)
Pressure Reduction Solenoid Valve (Port B) Off (Close) Off (Close) On (Open)
Wheel Cylinder Pressure Increases Holds Reduces



b.

Brake Assist

i.

In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a large amount of fluid pressure.

Brake Assist Control Operation
X112343C01
3.26,5.229 3.438,5.375 3.438,5.375 3.438,6.063 true 3.979,5.24 3.823,5.375 3.823,5.375 3.823,6.063 true 3.375,7.115 3.375,6.615 true 3.896,7.094 3.896,6.594 true 0.5,2.729 1.323,2.729 true 2.167,2.75 2.646,2.75 true 4.604,2.74 5.083,2.74 true 5.938,2.75 6.573,2.75 true 0.51,4.219 1.573,4.219 true 2.104,4.75 2.104,4.229 2.104,4.229 2.51,4.229 true 5.198,4.771 5.198,4.219 5.198,4.219 4.729,4.219 true 5.656,4.229 6.625,4.229 true 0.521,5.417 1.583,5.417 true 2.156,6.385 2.156,5.438 2.156,5.438 2.5,5.438 true 5.094,6.375 5.094,5.417 5.094,5.417 4.719,5.417 true 5.656,5.417 6.625,5.417 true 3.542,0.521 3.854,0.677 0.313,0.156 10 *1 0.292,2.646 0.604,2.958 0.313,0.313 10 (A) 5.552,1.76 5.865,1.917 0.313,0.156 10 *3 3.375,6.083 3.688,6.24 0.313,0.156 10 *4 3.313,7.146 3.625,7.302 0.313,0.156 10 *5 1.49,7.385 1.802,7.542 0.313,0.156 10 *6 2.531,7.375 2.844,7.531 0.313,0.156 10 *7 4.615,7.385 4.927,7.542 0.313,0.156 10 *8 5.698,7.365 6.01,7.521 0.313,0.156 10 *9 3.771,6.073 4.083,6.229 0.313,0.156 10 *4 3.844,7.125 4.156,7.281 0.313,0.156 10 *5 0.698,1.5 1.01,1.656 0.313,0.156 10 *2 1.958,2.667 2.271,2.979 0.313,0.313 10 (B) 5.115,2.667 5.427,2.979 0.313,0.313 10 (C) 6.625,2.667 6.938,2.979 0.313,0.313 10 (D) 1.229,3.323 1.542,3.635 0.313,0.313 10 (1) 2.531,3.323 2.844,3.635 0.313,0.313 10 (2) 4.49,3.344 4.802,3.656 0.313,0.313 10 (3) 5.813,3.323 6.125,3.635 0.313,0.313 10 (4) 0.313,4.135 0.625,4.448 0.313,0.313 10 (E) 2.042,4.781 2.354,5.094 0.313,0.313 10 (F) 5.115,4.792 5.427,5.104 0.313,0.313 10 (G) 1.51,4.823 1.823,5.135 0.313,0.313 10 (5) 2.438,4.813 2.75,5.125 0.313,0.313 10 (6) 4.604,4.823 4.917,5.135 0.313,0.313 10 (7) 5.542,4.813 5.854,5.125 0.313,0.313 10 (8) 1.49,6.01 1.802,6.323 0.313,0.313 10 (9) 2.427,5.99 2.74,6.302 0.313,0.313 10 (10) 4.594,6 4.906,6.313 0.313,0.313 10 (11) 5.49,6.01 5.802,6.323 0.313,0.313 10 (12) 6.656,4.146 6.969,4.458 0.313,0.313 10 (H) 0.365,5.323 0.677,5.635 0.313,0.313 10 (I) 2.104,6.406 2.417,6.719 0.313,0.313 10 (J) 5.021,6.396 5.333,6.708 0.313,0.313 10 (K) 6.667,5.323 6.979,5.635 0.313,0.313 10 (L)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


Brake Assist Control Operation
Item Port Brake Assist Not Activated Brake Assist Activated

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) On (Open)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) Off (Open) Off (Open)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) Off (Closed) Off (Closed)
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) Off (Open) Off (Open)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) Off (Closed) Off (Closed)
Pump Off On



c.

TRC

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. As a result, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure increase, pressure holding and pressure reduction modes to control the slippage of the drive wheels. Each pressure holding solenoid valve and the pressure reduction solenoid valve is turned on or off in accordance with the ABS and EBD operation patterns.

TRC Control Operation
X116976C03
0.625,2.75 1.323,2.75 true 2.177,2.74 2.646,2.74 true 4.594,2.74 5.063,2.74 true 5.917,2.74 6.615,2.74 true 0.677,4.219 1.583,4.219 true 2.063,4.615 2.063,4.219 2.063,4.219 2.51,4.219 true 5.177,4.635 5.177,4.229 5.177,4.229 4.708,4.229 true 5.635,4.229 6.542,4.229 true 0.688,5.406 1.594,5.406 true 2.146,6.365 2.146,5.406 2.146,5.406 2.521,5.406 true 5.094,6.396 5.094,5.427 5.094,5.427 4.719,5.427 true 5.646,5.417 6.552,5.417 true 3.438,6.063 3.438,5.375 3.438,5.375 3.26,5.24 true 3.802,6.073 3.802,5.385 3.802,5.385 3.979,5.24 true 3.365,6.604 3.365,7.063 true 3.875,6.604 3.875,7.063 true 3.521,0.531 3.833,0.688 0.313,0.156 10 false *1 0.646,1.531 0.958,1.688 0.313,0.156 10 false *2 5.531,1.792 5.844,1.948 0.313,0.156 10 false *3 3.354,6.104 3.667,6.26 0.313,0.156 10 false *4 3.302,7.104 3.615,7.26 0.313,0.156 10 false *5 1.51,7.271 1.823,7.427 0.313,0.156 10 false *6 2.448,7.271 2.76,7.427 0.313,0.156 10 false *7 4.604,7.25 4.917,7.406 0.313,0.156 10 false *8 5.583,7.229 5.896,7.385 0.313,0.156 10 false *9 0.427,2.688 0.74,2.844 0.313,0.156 10 false (A) 1.99,2.688 2.302,2.844 0.313,0.156 10 false (B) 5.094,2.677 5.406,2.833 0.313,0.156 10 false (C) 6.656,2.688 6.969,2.844 0.313,0.156 10 false (D) 1.26,3.344 1.573,3.5 0.313,0.156 10 false (1) 2.583,3.344 2.896,3.5 0.313,0.156 10 false (2) 4.531,3.333 4.844,3.49 0.313,0.156 10 false (3) 5.833,3.333 6.146,3.49 0.313,0.156 10 false (4) 0.458,4.167 0.771,4.323 0.313,0.156 10 false (E) 2,4.667 2.313,4.823 0.313,0.156 10 false (F) 5.115,4.688 5.427,4.844 0.313,0.156 10 false (G) 6.573,4.177 6.885,4.333 0.313,0.156 10 false (H) 0.49,5.344 0.802,5.5 0.313,0.156 10 false (I) 2.094,6.396 2.406,6.552 0.313,0.156 10 false (J) 5.031,6.427 5.344,6.583 0.313,0.156 10 false (K) 6.594,5.365 6.906,5.521 0.313,0.156 10 false (L) 1.542,4.823 1.854,4.979 0.313,0.156 10 false (5) 2.448,4.833 2.76,4.99 0.313,0.156 10 false (6) 4.646,4.833 4.958,4.99 0.313,0.156 10 false (7) 5.573,4.833 5.885,4.99 0.313,0.156 10 false (8) 1.542,6.052 1.854,6.208 0.313,0.156 10 false (9) 2.417,6.01 2.729,6.167 0.313,0.156 10 false (10) 4.604,6.01 4.917,6.167 0.313,0.156 10 false (11) 5.542,6.021 5.854,6.177 0.313,0.156 10 false (12) 3.719,6.104 4.031,6.26 0.313,0.156 10 false *4 3.813,7.104 4.125,7.26 0.313,0.156 10 false *5
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


TRC Control Operation*1
Item Port TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode

*1: This table shows the brake control operation of the 2WD. In the case of the 4WD/AWD, the rear brakes are also controlled with the same operation as the front brake.

*2: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On*2 On*2 On*2
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) On (Open) On (Open) On (Open)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) Off (Open) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) Off (Closed) Off (Closed) Off (Closed) On (Open)
Brake Wheel Cylinder Pressure - - - Increases Holds Reduces
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) Off (Open) On (Closed) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) Off (Closed) On (Open) On (Open) On (Open)
Brake Wheel Cylinder Pressure - - - - - -
Pump Off On On On



d.

VSC

i.

The VSC, by the way of solenoid valves, controls fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes. As a result, the tendency of front wheel skid or rear wheel skid is controlled.


ii.

In understeer restraining control, the brake of the front and rear wheels on the inner circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in pressure increase mode as it controls a front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.

VSC Operation (Understeer Restraining Control)
X112346C04
3.375,7.125 3.375,6.615 true 3.875,7.115 3.875,6.604 true 3.271,5.219 3.427,5.375 3.427,5.375 3.427,6.042 true 3.979,5.229 3.833,5.375 3.833,5.375 3.833,6.042 true 0.615,2.74 1.313,2.74 true 2.125,2.74 2.646,2.74 true 4.604,2.75 5.125,2.75 true 5.938,2.74 6.594,2.74 true 0.615,4.219 1.583,4.219 true 2.073,4.76 2.073,4.219 2.073,4.219 2.5,4.219 true 5.156,4.76 5.156,4.219 5.156,4.219 4.729,4.219 true 5.667,4.229 6.635,4.229 true 0.615,5.417 1.583,5.417 true 2.156,6.344 2.156,5.417 2.156,5.417 2.521,5.417 true 5.083,6.344 5.083,5.417 5.083,5.417 4.729,5.417 true 5.667,5.417 6.635,5.417 true 3.531,0.51 3.844,0.667 0.313,0.156 10 *1 0.688,1.438 1,1.594 0.313,0.156 10 *2 5.552,1.76 5.865,1.917 0.313,0.156 10 *3 3.375,6.073 3.688,6.229 0.313,0.156 10 *4 3.813,7.146 4.125,7.302 0.313,0.156 10 *5 1.458,7.313 1.771,7.469 0.313,0.156 10 *6 2.531,7.292 2.844,7.448 0.313,0.156 10 *7 4.573,7.323 4.885,7.479 0.313,0.156 10 *8 5.625,7.313 5.938,7.469 0.313,0.156 10 *9 3.323,7.167 3.635,7.323 0.313,0.156 10 *5 3.781,6.073 4.094,6.229 0.313,0.156 10 *4 0.396,2.667 0.698,2.99 0.302,0.323 10 (A) 1.917,2.667 2.219,2.99 0.302,0.323 10 (B) 5.167,2.677 5.469,3 0.302,0.323 10 (C) 6.635,2.667 6.938,2.99 0.302,0.323 10 (D) 0.406,4.146 0.708,4.469 0.302,0.323 10 (E) 2,4.792 2.302,5.115 0.302,0.323 10 (F) 5.094,4.792 5.396,5.115 0.302,0.323 10 (G) 6.667,4.156 6.969,4.479 0.302,0.323 10 (H) 0.458,5.333 0.76,5.656 0.302,0.323 10 (I) 2.083,6.375 2.385,6.698 0.302,0.323 10 (J) 5.031,6.375 5.333,6.698 0.302,0.323 10 (K) 6.677,5.344 6.979,5.667 0.302,0.323 10 (L) 1.271,3.323 1.583,3.573 0.313,0.25 10 (1) 2.583,3.323 2.896,3.573 0.313,0.25 10 (2) 4.51,3.323 4.823,3.573 0.313,0.25 10 (3) 5.833,3.313 6.146,3.563 0.313,0.25 10 (4) 1.531,4.823 1.844,5.073 0.313,0.25 10 (5) 2.448,4.823 2.76,5.073 0.313,0.25 10 (6) 4.646,4.813 4.958,5.063 0.313,0.25 10 (7) 5.573,4.813 5.885,5.063 0.313,0.25 10 (8) 1.531,6.01 1.844,6.26 0.313,0.25 10 (9) 2.448,6 2.76,6.25 0.313,0.25 10 (10) 4.615,6 4.927,6.25 0.313,0.25 10 (11) 5.552,6.021 5.865,6.271 0.313,0.25 10 (12)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


VSC Control Operation (During Understeer)
Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On* On* On*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) On (Open) On (Open) On (Open)
Front Brake Pressure Holding Solenoid Valve (5) (E) Off (Open) Off (Open) On (Closed) On (Closed)
(8) (H) Off (Open) On (Closed) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (9) (I) Off (Closed) Off (Closed) Off (Closed) On (Open)
(12) (L) Off (Closed) Off (Closed) Off (Closed) Off (Closed)
Brake Wheel Cylinder Pressure Right - - Increases Holds Reduces
Left - - - - -
Rear Brake Pressure Holding Solenoid Valve (6) (F) Off (Open) On (Closed) On (Closed) On (Closed)
(7) (G) Off (Open) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (10) (J) Off (Closed) Off (Closed) Off (Closed) Off (Closed)
(11) (K) Off (Closed) Off (Closed) Off (Closed) On (Open)
Brake Wheel Cylinder Pressure Right - - Increases Holds Reduces
Left - - - - -
Pump Off On On On


iii.

In oversteer restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in pressure increase mode, as it controls the rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.

VSC Operation (Oversteer Restraining Control)
X116977C02
0.688,2.74 1.333,2.74 true 2.125,2.75 2.656,2.75 true 4.594,2.75 5.125,2.75 true 5.906,2.75 6.552,2.75 true 0.74,4.219 1.594,4.219 true 2.073,4.719 2.073,4.229 2.073,4.229 2.51,4.229 true 5.198,4.729 5.198,4.229 5.198,4.229 4.708,4.229 true 5.635,4.208 6.448,4.208 true 0.74,5.417 1.594,5.417 true 2.146,6.333 2.146,5.396 2.146,5.396 2.521,5.396 true 5.646,5.417 6.5,5.417 true 5.094,6.354 5.094,5.417 5.094,5.417 4.708,5.417 true 3.438,6.052 3.438,5.396 3.438,5.396 3.26,5.229 true 3.813,6.052 3.813,5.396 3.813,5.396 4,5.229 true 3.365,6.615 3.365,7.167 true 3.865,6.604 3.865,7.156 true 3.542,0.5 3.854,0.656 0.313,0.156 10 false *1 0.667,1.49 0.979,1.646 0.313,0.156 10 false *2 5.552,1.771 5.865,1.927 0.313,0.156 10 false *3 3.385,6.104 3.698,6.26 0.313,0.156 10 false *4 3.281,7.188 3.594,7.344 0.313,0.156 10 false *5 1.479,7.26 1.792,7.417 0.313,0.156 10 false *6 2.542,7.25 2.854,7.406 0.313,0.156 10 false *7 4.594,7.24 4.906,7.396 0.313,0.156 10 false *8 5.656,7.24 5.969,7.396 0.313,0.156 10 false *9 0.5,2.677 0.813,2.833 0.313,0.156 10 false (A) 1.927,2.688 2.24,2.844 0.313,0.156 10 false (B) 5.167,2.688 5.479,2.844 0.313,0.156 10 false (C) 6.604,2.688 6.917,2.844 0.313,0.156 10 false (D) 1.292,3.333 1.552,3.5 0.26,0.167 10 false (1) 2.594,3.333 2.865,3.5 0.271,0.167 10 false (2) 4.51,3.323 4.771,3.49 0.26,0.167 10 false (3) 5.844,3.323 6.104,3.49 0.26,0.167 10 false (4) 1.521,4.833 1.781,5 0.26,0.167 10 false (5) 2.469,4.823 2.729,4.99 0.26,0.167 10 false (6) 4.646,4.823 4.906,4.99 0.26,0.167 10 false (7) 5.583,4.823 5.844,4.99 0.26,0.167 10 false (8) 0.552,4.146 0.865,4.302 0.313,0.156 10 false (E) 2.01,4.75 2.323,4.906 0.313,0.156 10 false (F) 5.125,4.76 5.438,4.917 0.313,0.156 10 false (G) 6.51,4.146 6.823,4.302 0.313,0.156 10 false (H) 2.104,6.365 2.417,6.521 0.313,0.156 10 false (J) 0.573,5.354 0.885,5.51 0.313,0.156 10 false (I) 5.031,6.354 5.344,6.51 0.313,0.156 10 false (K) 6.552,5.344 6.865,5.5 0.313,0.156 10 false (L) 1.521,6.021 1.781,6.188 0.26,0.167 10 false (9) 2.427,6.021 2.688,6.188 0.26,0.167 10 false (10) 4.604,6.021 4.865,6.188 0.26,0.167 10 false (11) 5.542,6.021 5.802,6.188 0.26,0.167 10 false (12) 3.719,6.104 4.031,6.26 0.313,0.156 10 false *4 3.792,7.188 4.104,7.344 0.313,0.156 10 false *5
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


VSC Control Operation (During Oversteer)
Item Port VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On* On* On*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) On (Open) On (Open) On (Open)
Front Brake Pressure Holding Solenoid Valve (5) (E) Off (Open) On (Closed) On (Closed) On (Closed)
(8) (H) Off (Open) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (9) (I) Off (Closed) Off (Closed) Off (Closed) Off (Closed)
(12) (L) Off (Closed) Off (Closed) Off (Closed) On (Open)
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increases Holds Reduces
Rear Brake Pressure Holding Solenoid Valve (6) (F) Off (Open) Off (Open) On (Closed) On (Closed)
(7) (G) Off (Open) On (Closed) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (10) (J) Off (Closed) Off (Closed) Off (Closed) On (Open)
(11) (K) Off (Closed) Off (Closed) Off (Closed) Off (Closed)
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increases Holds Reduces
Pump Off On On On



e.

Active Cornering Assist (ACA)

i.

Active Cornering Assist (ACA), by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer tendencies are controlled.


ii.

Understeer restraining control is performed by applying the brakes on the inner circle of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking.


iii.

The operation of the solenoid valves under the ACA is the same as the VSC operation.



f.

Steering Cooperative Control

i.

The operation of the solenoid valves under the steering cooperative control is the same as the TRC or VSC operation.



g.

Trailer Sway Control

i.

The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.



h.

Hill-start Assist Control

i.

Hill-start assist control is performed by closing the master cylinder cut solenoid valves after the driver operates the brake pedal and leaving a certain amount of hydraulic pressure created by the pump in the wheel cylinder. The diagram below shows the hydraulic circuit in pressure holding mode.

Hill-start Assist Control Operation
X142722C01
3.271,5.229 3.417,5.385 3.417,5.385 3.417,6.094 true 3.99,5.25 3.823,5.385 3.823,5.385 3.823,6.073 true 3.365,7.063 3.365,6.625 true 3.875,7.073 3.875,6.635 true 0.542,2.75 1.323,2.75 true 2.135,2.75 2.646,2.75 true 4.604,2.75 5.115,2.75 true 5.927,2.75 6.677,2.75 true 0.552,4.219 1.594,4.219 true 2.042,4.531 2.042,4.219 2.042,4.219 2.5,4.219 true 5.167,4.479 5.167,4.219 5.167,4.219 4.729,4.219 true 5.667,4.219 6.698,4.219 true 0.552,5.406 1.573,5.406 true 2.156,6.333 2.156,5.406 2.156,5.406 2.5,5.417 true 5.083,6.354 5.083,5.406 5.083,5.406 4.74,5.406 true 5.667,5.417 6.698,5.417 true 3.531,0.552 3.844,0.708 0.313,0.156 10 *1 0.677,1.458 0.99,1.615 0.313,0.156 10 *2 5.521,1.781 5.833,1.938 0.313,0.156 10 *3 3.365,6.104 3.677,6.26 0.313,0.156 10 *4 3.313,7.104 3.625,7.26 0.313,0.156 10 *5 1.385,7.271 1.698,7.427 0.313,0.156 10 *6 2.51,7.281 2.823,7.438 0.313,0.156 10 *7 4.604,7.26 4.917,7.417 0.313,0.156 10 *8 5.646,7.281 5.958,7.438 0.313,0.156 10 *9 3.76,6.104 4.073,6.26 0.313,0.156 10 *4 3.823,7.094 4.135,7.25 0.313,0.156 10 *5 1.917,2.656 2.375,2.854 0.458,0.198 10 (B) 0.333,2.667 0.792,2.865 0.458,0.198 10 (A) 5.167,2.677 5.625,2.875 0.458,0.198 10 (C) 6.719,2.667 7.031,2.906 0.313,0.24 10 (D) 1.26,3.344 1.719,3.542 0.458,0.198 10 (1) 2.573,3.333 3.031,3.531 0.458,0.198 10 (2) 4.51,3.333 4.969,3.531 0.458,0.198 10 (3) 5.823,3.354 6.281,3.552 0.458,0.198 10 (4) 1.531,4.802 1.99,5 0.458,0.198 10 (5) 2.448,4.813 2.906,5.01 0.458,0.198 10 (6) 4.635,4.823 5.094,5.021 0.458,0.198 10 (7) 5.563,4.823 6.021,5.021 0.458,0.198 10 (8) 1.542,6.01 2,6.208 0.458,0.198 10 (9) 2.396,6 2.854,6.198 0.458,0.198 10 (10) 4.604,6 5.063,6.198 0.458,0.198 10 (11) 5.531,6.01 5.99,6.208 0.458,0.198 10 (12) 0.344,4.125 0.802,4.323 0.458,0.198 10 (E) 1.969,4.573 2.427,4.771 0.458,0.198 10 (F) 5.083,4.51 5.542,4.708 0.458,0.198 10 (G) 6.74,4.125 7.052,4.365 0.313,0.24 10 (H) 0.396,5.313 0.854,5.51 0.458,0.198 10 (I) 2.094,6.354 2.552,6.552 0.458,0.198 10 (J) 5.01,6.385 5.469,6.583 0.458,0.198 10 (K) 6.74,5.323 7.052,5.563 0.313,0.24 10 (L)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


Hill-start Assist Control Operation
Item Port Hill-start Assist Control Not Activated Hill-start Assist Control Activated
Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On* On*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) Off (Closed) Off (Closed)
Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) Off (Open) Off (Open) Off (Open)
Pressure Reduction Solenoid Valve (9), (12) (I), (L) Off (Closed) Off (Closed) Off (Closed)
Brake Wheel Cylinder Pressure - - Holds Reduces
Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) Off (Open) Off (Open) Off (Open)
Pressure Reduction Solenoid Valve (10), (11) (J), (K) Off (Closed) Off (Closed) Off (Closed)
Brake Wheel Cylinder Pressure - - Holds Reduces
Pump Off Off Off



i.

Brake Hold

i.

The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.



j.

Downhill Assist Control

i.

Based on the information provided by various sensors, switches and the ECM, the skid control ECU determines the conditions that enable the downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the pump and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.


ii.

The skid control ECU computes the vehicle speed, travel direction and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate and deceleration sensor, and performs brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.

Travel Direction Target Vehicle Speed
Forward 5 km/h to 7 km/h (3 mph to 4 mph)
Backward 3 km/h to 5 km/h (2 mph to 3 mph)


iii.

During the downhill assist control operation, the skid control ECU outputs signals to the stop light switch assembly to cause the stop light to turn on and to the combination meter assembly to cause the slip indicator light to blink.

Downhill Assist Control Operation
X112343C01
3.26,5.229 3.438,5.375 3.438,5.375 3.438,6.063 true 3.979,5.24 3.823,5.375 3.823,5.375 3.823,6.063 true 3.375,7.115 3.375,6.615 true 3.896,7.094 3.896,6.594 true 0.5,2.729 1.323,2.729 true 2.167,2.75 2.646,2.75 true 4.604,2.74 5.083,2.74 true 5.938,2.75 6.573,2.75 true 0.51,4.219 1.573,4.219 true 2.104,4.75 2.104,4.229 2.104,4.229 2.51,4.229 true 5.198,4.771 5.198,4.219 5.198,4.219 4.729,4.219 true 5.656,4.229 6.625,4.229 true 0.521,5.417 1.583,5.417 true 2.156,6.385 2.156,5.438 2.156,5.438 2.5,5.438 true 5.094,6.375 5.094,5.417 5.094,5.417 4.719,5.417 true 5.656,5.417 6.625,5.417 true 3.542,0.521 3.854,0.677 0.313,0.156 10 *1 0.292,2.646 0.604,2.958 0.313,0.313 10 (A) 5.552,1.76 5.865,1.917 0.313,0.156 10 *3 3.375,6.083 3.688,6.24 0.313,0.156 10 *4 3.313,7.146 3.625,7.302 0.313,0.156 10 *5 1.49,7.385 1.802,7.542 0.313,0.156 10 *6 2.531,7.375 2.844,7.531 0.313,0.156 10 *7 4.615,7.385 4.927,7.542 0.313,0.156 10 *8 5.698,7.365 6.01,7.521 0.313,0.156 10 *9 3.771,6.073 4.083,6.229 0.313,0.156 10 *4 3.844,7.125 4.156,7.281 0.313,0.156 10 *5 0.698,1.5 1.01,1.656 0.313,0.156 10 *2 1.958,2.667 2.271,2.979 0.313,0.313 10 (B) 5.115,2.667 5.427,2.979 0.313,0.313 10 (C) 6.625,2.667 6.938,2.979 0.313,0.313 10 (D) 1.229,3.323 1.542,3.635 0.313,0.313 10 (1) 2.531,3.323 2.844,3.635 0.313,0.313 10 (2) 4.49,3.344 4.802,3.656 0.313,0.313 10 (3) 5.813,3.323 6.125,3.635 0.313,0.313 10 (4) 0.313,4.135 0.625,4.448 0.313,0.313 10 (E) 2.042,4.781 2.354,5.094 0.313,0.313 10 (F) 5.115,4.792 5.427,5.104 0.313,0.313 10 (G) 1.51,4.823 1.823,5.135 0.313,0.313 10 (5) 2.438,4.813 2.75,5.125 0.313,0.313 10 (6) 4.604,4.823 4.917,5.135 0.313,0.313 10 (7) 5.542,4.813 5.854,5.125 0.313,0.313 10 (8) 1.49,6.01 1.802,6.323 0.313,0.313 10 (9) 2.427,5.99 2.74,6.302 0.313,0.313 10 (10) 4.594,6 4.906,6.313 0.313,0.313 10 (11) 5.49,6.01 5.802,6.323 0.313,0.313 10 (12) 6.656,4.146 6.969,4.458 0.313,0.313 10 (H) 0.365,5.323 0.677,5.635 0.313,0.313 10 (I) 2.104,6.406 2.417,6.719 0.313,0.313 10 (J) 5.021,6.396 5.333,6.708 0.313,0.313 10 (K) 6.667,5.323 6.979,5.635 0.313,0.313 10 (L)
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 Pump
*5 Reservoir *6 Front Brake Caliper (Right Side)
*7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
*9 Front Brake Caliper (Left Side) - -


Downhill Assist Control Operation
Item Port Downhill Assist Control Not Activated Downhill Assist Control Activated
Increase Mode Holding Mode Reduction Mode

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) Off (Open) On* On* On*
Reservoir Cut Solenoid Valve (2), (3) (B), (C) Off (Closed) On (Open) On (Open) On (Open)
Front Brake Pressure Holding Solenoid Valve (5) (E) Off (Open) Off (Open) On (Closed) On (Closed)
(8) (H) Off (Open) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (9) (I) Off (Closed) Off (Closed) Off (Closed) On (Open)
(12) (L) Off (Closed) Off (Closed) Off (Closed) On (Open)
Brake Wheel Cylinder Pressure Right - - Increases Holds Reduces
Left - - Increases Holds Reduces
Rear Brake Pressure Holding Solenoid Valve (6) (F) Off (Open) Off (Open) On (Closed) On (Closed)
(7) (G) Off (Open) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (10) (J) Off (Closed) Off (Closed) Off (Closed) On (Open)
(11) (K) Off (Closed) Off (Closed) Off (Closed) On (Open)
Brake Wheel Cylinder Pressure Right - - Increases Holds Reduces
Left - - Increases Holds Reduces
Pump Off On On On