FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Except models for G.C.C. countries and LHD models for Europe *2: Models with manual transaxle *3: Models without manual transaxle *4: Models with downhill assist control *5: 4WD/AWD models *6: Models with automatic transaxle *7: Models with CVT *8: Models with GF2A type transfer *9: Models with pre-collision system |
||
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | |
| Steering Sensor | Detects the direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Brake Pedal Load Sensing Switch*1 | Detects the brake pedal load. | |
| VSC OFF Switch | Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode". | |
| Brake Warning Switch Assembly*2 | Brake Hold Switch | Switches the brake hold on and off. |
| Integration Control and Panel Assembly | Brake Hold Switch*3 | Switches the brake hold on and off. |
| Downhill Assist Control Switch*4 | Allows the driver to turn downhill assist control on and off. | |
| MUD & SAND Switch*5 | Selects the "MUD & SAND" multi-terrain select mode. | |
| ROCK & DIRT Switch*5 | Selects the "ROCK & DIRT" multi-terrain select mode. | |
| Hazard Warning Signal Switch Assembly | Switches the Hazard Warning Signal on and off. | |
| Brake Actuator Assembly | Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Solenoid Valves | Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions in order to control the fluid pressure applied to the wheel cylinders. | |
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Master Cylinder Pressure Sensor | Detects the master cylinder pressure. | |
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each ECU, sensor and switch, and sends the brake control signals to the brake actuator. | |
| ECM | ·
Controls the drive force when TRC and VSC are operating according to communication with the skid control ECU. ·
Sends the accelerator pedal position signal, reverse position signal*2, shift position signal*6, throttle position signal, engine speed signal and brake request signal to the skid control ECU. |
|
| Transmission Control ECU*7 | Sends the shift position signal to the skid control ECU. | |
| Power Steering ECU with Motor Assembly | Power Steering ECU | Controls the steering assist torque based on the signals received from the skid control ECU. |
| Main Body ECU (Multiplex Network Body ECU) | Sends the driver side door opening or closing state signal and seat belt fasten condition signal to the skid control ECU. | |
| 4WD ECU Assembly*5 | ·
Operates in cooperation with the skid control ECU to control the torque distribution between the front and rear wheels. ·
Operates in cooperation with the skid control ECU to control the torque distribution between the left and right on rear wheels.*8 |
|
| Airbag ECU Assembly | ·
Sends the collision detection signal to the skid control ECU.*9 ·
The yawrate sensor detects the vehicle's yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral deceleration. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | |
| Combination Meter Assembly | Brake Warning Light / Red (Malfunction) | ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD. ·
Illuminates to inform the driver when the brake fluid is low. |
| Brake Warning Light / Yellow (Minor Malfunction) | Illuminates to alert the driver when the skid control ECU detected a malfunction in the electric parking brake system. | |
| ABS Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS. | |
| Slip Indicator Light | ·
Blinks to inform the driver when the TRC, VSC or downhill assist control*4 is operational. ·
Blinks to alert the driver when the skid control ECU detects a malfunction in the downhill assist control.*4 ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC, VSC or hill-start assist control. |
|
| VSC OFF Indicator Light | Illuminates to inform the driver when VSC OFF mode is selected. | |
| Brake Hold Indicator Light (Green Indicator) | Illuminates to inform the driver that the brake hold standby condition has been established. | |
| Brake Hold Indicator Light (Yellow Indicator) | ·
Illuminates to inform the driver that the brake hold is operating. ·
Blinks to alert the driver when the skid control ECU detects a malfunction in the brake hold. |
|
| Downhill Assist Control Indicator Light*4 | Illuminates to inform the driver when downhill assist control operation is possible. | |
| MUD & SAND Indicator Light*5 | Illuminates to inform the driver when "MUD & SAND" multi-terrain select mode is selected. | |
| ROCK & DIRT Indicator Light*5 | Illuminates to inform the driver when "ROCK & DIRT" multi-terrain select mode is selected. | |
| Multi-information Display | ·
Displays the warning message when the skid control ECU detects a malfunction in the system. ·
Displays the information message when TRC OFF mode is selected. |
|
| Buzzer | Sounds together with a message display on the multi-information display during a system malfunction. | |
OPERATING CONDITION
Hill-start Assist Control
Hill-start assist control operates when all of the following conditions have been met:
|
*1: Models without manual transaxle *2: Models with manual transaxle |
·
The shift position is in any position other than P, N or R (when forward climbing).*1 ·
The shift position is in any position other than R (when forward climbing).*2 ·
The shift position is in R (when backward climbing). ·
The brake pedal is depressed and the vehicle is stopped. ·
The accelerator pedal is not depressed. ·
The parking brake is not applied. |
If any one of the following conditions is met during hill-start assist control operation, hill-start assist control will be canceled.
|
*1: Models without manual transaxle *2: Models with manual transaxle |
·
The shift position is moved to P, N or R (when forward climbing).*1 ·
The shift position is moved to R (when forward climbing).*2 ·
The shift position is moved to a position other than R (when backward climbing). ·
The accelerator pedal is depressed. ·
The parking brake is applied. ·
2 seconds have elapsed since the driver released the brake pedal. |
Downhill Assist Control
Downhill assist control operates when all of the following conditions are met with the downhill assist control switch turned on:
|
*1: Models with automatic transaxle *2: Models with CVT |
·
The shift position is in S1*1, M1*2 or R. ·
The accelerator pedal and brake pedal are not depressed. ·
The vehicle speed is 25 km/h (16 mph) or less while moving downhill. |
Downhill assist control does not operate under the conditions described below even if the downhill assist control switch is turned on. In this case, the downhill assist control indicator light blinks to alert the driver.
|
*1: Models with automatic transaxle *2: Models with CVT |
·
The shift position is moved to any position other than S1*1, M1*2, N or R. ·
The vehicle speed is greater than about 25 km/h (16 mph). ·
A malfunction occurs in the downhill assist control system. ·
The temperature of the brake actuator rises, causing the downhill assist control operation to stop. |
The downhill assist control indicator light flashes to warn the driver when any of the following conditions is met, but downhill assist control is still performed.
The downhill assist control switch is turned off while downhill assist control is operating. Afterward, brake hydraulic pressure gradually decreases and downhill assist control stops.
The shift position is moved to N.
Brake Hold
Brake Hold Standby Condition
To operate the brake hold, it is first necessary to establish the brake hold standby condition. The brake hold standby condition is established when the driver presses the brake hold switch after all the conditions listed below have been met. As a result, the brake hold indicator light (green indicator) illuminates in the combination meter assembly.
|
*1: Models with automatic transaxle *2: Models with CVT |
·
The engine control system, A/T system*1, CVT system*2, electric parking brake system, brake control system and brake system are all operating normally. ·
The driver door is closed. ·
The driver seat belt is buckled. |
Brake Hold Operation Condition
When all of the conditions listed below are met while the brake hold standby condition is established, the brake hold will operate. When the brake hold operates, the brake hold indicator light (yellow indicator) will illuminate in the combination meter assembly.
|
*1: Models without manual transaxle *2: Models with manual transaxle |
·
The shift position is in any position other than P or R.*1 ·
The shift position is in any position other than R.*2 ·
The brake pedal is depressed and the vehicle is stopped. ·
The accelerator pedal is not depressed. ·
The vehicle is not on a steep gradient. |
If the brake hold is inoperative because the vehicle is on a steep gradient, the system informs the driver by turning off the brake hold indicator light (yellow indicator) and outputting a warning message on the multi-information display. To support the start off of the vehicle on a steep uphill gradient, hill-start assist control will operate.
Brake Hold Operation Ending Condition
When one of the conditions listed below has been established, the skid control ECU ends the brake hold function. In addition, the skid control ECU informs the driver that the brake hold function has ended by turning off the brake hold indicator light (yellow indicator).
|
*: Models without manual transaxle |
·
The accelerator pedal is depressed. ·
The shift position is shifted to P.* ·
The shift position is shifted to R. |
Electric Parking Brake Operation Condition
If any one of the conditions listed below is established while the brake hold function is operating and the driver is not depressing the brake pedal, the electric parking brake will lock automatically.
·
The driver door is open. ·
The driver seat belt is unbuckled. ·
3 minutes have elapsed since the brake hold function operated. |
After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section.
Brake Hold Standby Condition Canceling Condition
If any one of the conditions listed below occurs while the brake hold standby condition is established, the skid control ECU cancels the brake hold standby condition.
·
The electric parking brake has locked automatically as a result of the driver seat belt being unbuckled or the driver door being opened. ·
Any one of the following takes place while the vehicle is being driven: the driver seat belt is unbuckled or the driver door is opened. ·
The brake hold switch is pressed while the brake hold function is inoperative. ·
The brake hold switch is pressed while the brake pedal is depressed and the brake hold function is operating. |
Brake Hold Operation Prohibition Condition
If any system malfunction listed below occurs, the skid control ECU prohibits the operation of the brake hold function. At this time, the skid control ECU alerts the driver by flashing the brake hold indicator light (yellow indicator).
|
*1: When the wheel cylinder pressure cannot be maintained while the brake hold function is operating, the parking brake automatically locks. After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section. *2: Models with automatic transaxle *3: Models with CVT |
·
An engine control system malfunction occurs. ·
An electric parking brake system malfunction occurs. ·
A brake system and brake control system malfunction occurs.*1 ·
An A/T system malfunction occurs.*2 ·
A CVT system malfunction occurs.*3 |
Active Cornering Assist (ACA)
Active Cornering Assist (ACA) operates when all of the following conditions are met.
·
VSC/TRC operation is permitted. ·
The system detects an understeer tendency. ·
The brake pedal is not depressed. ·
The driver is attempting to accelerate while turning. |
Secondary Collision Brake
Secondary Collision Brake Operation Start Condition
When a collision detection signal is received from the airbag ECU while the vehicle speed is approximately 10 km/h or more, the secondary collision brake starts operating.
When a system malfunction is displayed on the multi-information display or the system is in test mode or maintenance mode, the secondary collision brake is prohibited from operating.
Secondary Collision Brake Operation Cancellation Condition
If one of the following conditions is detected, operation of the secondary collision brake is canceled.
·
The vehicle speed is below approximately 10 km/h. ·
Operation continues for a certain period of time. ·
After operating, the accelerator pedal is depressed a certain amount or more. |
Emergency Brake Signal
Operation conditions of the emergency brake signal
Emergency brake signal operates when all of the following conditions have been met:
·
The vehicle speed is approximately 55 km/h or more. ·
The brake pedal is depressed and the vehicle is judged to be rapidly braking based on the deceleration rate. |
Cancellation conditions of the emergency brake signal
If any one of the following conditions is met during emergency brake signal operation, emergency brake signal will be canceled.
·
When the hazard warning lights are turned on by operating the hazard warning signal switch. ·
The brake pedal is released. ·
The parking brake is applied. ·
The deceleration rate of the vehicle is judged not to be high. The vehicle is judged not to be rapidly braking based on the deceleration rate. |
SYSTEM CONTROL
The brake control system has the following controls:
| Control | Outline |
|---|---|
|
*1: Models with downhill assist control *2: Models with CVT *3: Models with automatic transaxle *4: Except destination package for Korea *5: Models with pre-collision system |
|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | The EBD utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, the EBD also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, helping ensure the vehicle's braking performance. |
| Traction Control (TRC) | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface. |
| Vehicle Stability Control (VSC) | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering. |
| Active Cornering Assist (ACA) | ACA performs brake control that applies braking force to the inside wheels when turning during periods of high acceleration, such as when the driver is depressing the accelerator pedal, generating a vehicle yaw moment. As a result, the tendency of the vehicle to understeer is suppressed, ensuring superior turning performance. |
| Steering Cooperative Control | The steering cooperative control performs cooperative control with the power steering ECU in order to provide steering assist in accordance with the operating conditions of the vehicle. |
| Trailer Sway Control | If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the engine output in order to suppress trailer sway. |
| Hill-start Assist Control | When starting uphill, this control maintains the brake hydraulic pressure on all 4 wheels in order to momentarily prevent the vehicle from descending backward. |
| Downhill Assist Control*1 | The downhill assist control is used when driving downhill on a sharp slope on which the engine brake alone will not adequately decelerate the vehicle. The driver can operate the downhill assist control switch while the shift range is in M1*2, S1*3 or R, in order to automatically control the brake hydraulic pressure to the four wheels. |
| Brake Hold Function | As the driver depresses the brake pedal and the vehicle comes to a stop, this function maintains the hydraulic pressure of the 4 wheels in order to keep the vehicle stopped. |
| Emergency Brake Signal*4 | In case of emergency braking, the emergency brake signal flashes the hazard warning lights to alert drivers in following vehicles. |
| Secondary Collision Brake*5 | After the airbags operate, this system automatically operates the brakes to suppress movement after a collision. |
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTCs and check function, refer to the Repair Manual.