FUNCTION OF MAIN COMPONENTS
| Component | Function | ||
|---|---|---|---|
|
*: Models with pre-collision system |
|||
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | ||
| Steering Sensor | Detects the direction and angle of the steering wheel. | ||
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | ||
| Brake Pedal Stroke Sensor Assembly | Directly detects the extent of the brake pedal stroke operated by the driver. | ||
| VSC OFF Switch | Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode". | ||
| Integration Control and Panel Assembly | Brake Hold Switch | Switches the brake hold on and off. | |
| Hazard Warning Signal Switch Assembly | Switches the Hazard Warning Signal on and off. | ||
| Front Door Courtesy Light Switch Assembly (for Driver Door) | Detects whether the door is open or closed and sends the information to the skid control ECU. | ||
| Brake Master Cylinder Reservoir Assembly | Brake Fluid Level Warning Switch | Detects the low brake fluid level. | |
| Brake Booster Pump Assembly | Pump Motor | Supplies brake fluid pressurized by the motor to the accumulator. | |
| Accumulator | Accumulates brake fluid supplied by the pump motor. | ||
| Brake Booster with Master Cylinder Assembly | Brake Actuator | Wheel Cylinder Pressure Sensor | Detects the wheel cylinder pressure. |
| Accumulator Pressure Sensor | Detects the accumulator pressure. | ||
| Regulator Pressure Sensor | Detects the regulator pressure of the brake master cylinder. | ||
| Linear Solenoid Valve (SLA, SLR) | Switches the brake fluid path during regenerative brake cooperative control to increase, decrease or maintain the hydraulic pressure applied to the wheel cylinder. | ||
| Switching Solenoid Valve (SSC) | Switches the brake fluid path to shut off or release the hydraulic pressure applied to the brake master stroke simulator cylinder assembly from the brake master cylinder. | ||
| Switching Solenoid Valve (SCC) | Shuts off or releases the brake fluid path on the front brake side and rear brake side. | ||
| Switching Solenoid Valve (SMC, SRC) | Switches the brake fluid path to shut off or release the hydraulic pressure applied to the wheel cylinder from the brake master cylinder. | ||
| Control Solenoid Valve
·
Pressure Holding Solenoid Valve ·
Pressure Reduction Solenoid Valve |
Switches the brake fluid path during brake control system operation to increase, decrease or maintain the hydraulic pressure applied to the wheel cylinder. | ||
| Brake Master Cylinder | ·
Generates hydraulic pressure in accordance with the amount of effort applied to the brake pedal by the driver. ·
When a malfunction occurs in the brake system, the brake master cylinder supplies the fluid pressure (which is generated by the brake pedal effort) directly to the wheel cylinders. |
||
| Brake Master Stroke Simulator Cylinder Assembly | Generates a pedal stroke during braking in accordance with the driver's pedal effort. | ||
| Skid Control ECU | ·
Performs regenerative brake cooperative control according to communication with the hybrid vehicle control ECU. ·
Operates the brake actuator according to signals from sensors and ECUs to control the brake hydraulic pressure of each wheel. ·
Operates the brake booster pump assembly to control accumulator pressure based on accumulator pressure sensor signals. |
||
| Hybrid Vehicle Control ECU | ·
Controls the brake force of regenerative braking during regenerative brake cooperative control according to communication with the skid control ECU. ·
Controls the motive force when TRC and VSC are operating according to communication with the skid control ECU. ·
Sends the accelerator pedal position signal, shift position signal and brake request signal to the skid control ECU. |
||
| Parking Brake ECU Assembly | Operates the parking brake actuator assembly according to signals from the skid control ECU. | ||
| Power Steering ECU with Motor Assembly | Power Steering ECU | Controls the steering assist torque based on the signals received from the skid control ECU. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends the driver side door opening or closing state signal and seat belt fasten condition signal to the skid control ECU. | ||
| Airbag ECU (Airbag Sensor Assembly) | ·
Sends the collision detection signal to the skid control ECU.* ·
The yawrate sensor detects the vehicle's yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral deceleration. |
||
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | ||
| Combination Meter Assembly | Brake Warning Light / Red (Malfunction) | ·
Illuminates to alert the driver that the skid control ECU detects the malfunction in the apportioning of the brake force. ·
Illuminates to inform the driver when the brake fluid is low. |
|
| Brake Warning Light / Yellow (Minor Malfunction) | Illuminates to alert the driver that a minor malfunction which does not affect the braking force has occurred in the brake system. | ||
| ABS Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS. | ||
| Slip Indicator Light | ·
Blinks to inform the driver when the TRC, VSC or ABS is operational. ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC, VSC or hill-start assist control. |
||
| VSC OFF Indicator Light | Illuminates to inform the driver when VSC OFF mode is selected. | ||
| Brake Hold Indicator Light (Green Indicator) | Illuminates to inform the driver that the brake hold standby condition has been established. | ||
| Brake Hold Indicator Light (Yellow Indicator) | ·
Illuminates to inform the driver that the brake hold is operating. ·
Blinks to alert the driver when the skid control ECU detects a malfunction in the brake hold. |
||
| Multi-information Display | ·
Displays the warning message when the skid control ECU detects a malfunction in the system. ·
Displays the information message when TRC OFF mode is selected. |
||
| Buzzer | Sounds together with a message display on the multi-information display during a system malfunction. | ||
OPERATING CONDITION
Hill-start Assist Control
Hill-start assist control operates when all of the following conditions have been met:
·
The shift position is in any position other than P or N (when taking off or reversing on an uphill slope). ·
The brake pedal is depressed and the vehicle is stopped. ·
The accelerator pedal is not depressed. ·
The parking brake is not applied. |
If any one of the following conditions is met during hill-start assist control operation, hill-start assist control will be canceled.
·
The shift position is shifted to P or N. ·
The accelerator pedal is depressed. ·
The parking brake is applied. ·
2 seconds have elapsed since the driver released the brake pedal. |
Brake Hold
Brake Hold Standby Condition
To operate the brake hold, it is first necessary to establish the brake hold standby condition. The brake hold standby condition is established when the driver presses the brake hold switch after all the conditions listed below have been met. As a result, the brake hold indicator light (green indicator) illuminates in the combination meter assembly.
·
The hybrid control system, electric parking brake system and electronically controlled brake system are all operating normally. ·
The driver door is closed. ·
The driver seat belt is buckled. |
Brake Hold Operation Condition
When all of the conditions listed below are met while the brake hold standby condition is established, the brake hold will operate. When the brake hold operates, the brake hold indicator light (yellow indicator) will illuminate in the combination meter assembly.
·
The shift position is in any position other than P or R. ·
The brake pedal is depressed and the vehicle is stopped. ·
The accelerator pedal is not depressed. ·
The vehicle is not on a steep gradient. |
If the brake hold is inoperative because the vehicle is on a steep gradient, the system informs the driver by turning off the brake hold indicator light (yellow indicator) and outputting a warning message on the multi-information display. To support the start off of the vehicle on a steep uphill gradient, hill-start assist control will operate.
Brake Hold Operation Ending Condition
When one of the conditions listed below has been established, the skid control ECU ends the brake hold function. In addition, the skid control ECU informs the driver that the brake hold function has ended by turning off the brake hold indicator light (yellow indicator).
·
The accelerator pedal is depressed. ·
The shift position is shifted to P. ·
The shift position is shifted to R while depressing the brake pedal. |
Electric Parking Brake Operation Condition
If any one of the conditions listed below is established while the brake hold function is operating and the driver is not depressing the brake pedal, the electric parking brake will lock automatically.
·
The driver door is open ·
The driver seat belt is unbuckled. ·
3 minutes have elapsed since the brake hold function operated. |
After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section.
Brake Hold Standby Condition Canceling Condition
If any one of the conditions listed below occurs while the brake hold standby condition is established, the skid control ECU cancels the brake hold standby condition.
·
The electric parking brake has locked automatically as a result of the driver seat belt being unbuckled or the driver door being opened. ·
Any one of the following takes place while the vehicle is being driven: the driver seat belt is unbuckled or the driver door is opened. ·
The brake hold switch is pressed while the brake hold function is inoperative. ·
The brake hold switch is pressed while the brake pedal is depressed and the brake hold function is operating. |
Brake Hold Operation Prohibition Condition
If any system malfunction listed below occurs, the skid control ECU prohibits the operation of the brake hold function. At this time, the skid control ECU alerts the driver by flashing the brake hold indicator light (yellow indicator).
·
A hybrid control system malfunction occurs. ·
An electric parking brake system malfunction occurs. ·
An electronically controlled brake system malfunction occurs.* |
*: When the wheel cylinder pressure cannot be maintained while the brake hold function is operating, the parking brake automatically locks. After the electric parking brake is locked, make sure to operate the manual function or automatic parking brake release function to release the parking brake before starting off. For details, see the Electric Parking Brake System section.
Active Cornering Assist (ACA)
Active Cornering Assist (ACA) operates when all of the following conditions are met.
·
VSC/TRC operation is permitted. ·
The system detects an understeer tendency. ·
The brake pedal is not depressed. ·
The driver is attempting to accelerate while turning. |
Secondary Collision Brake
Secondary Collision Brake Operation Start Condition
When a collision detection signal is received from the airbag ECU while the vehicle speed is approximately 10 km/h or more, the secondary collision brake starts operating.
When a system malfunction is displayed on the multi-information display or the system is in test mode or maintenance mode, the secondary collision brake is prohibited from operating.
Secondary Collision Brake Operation Cancellation Condition
If one of the following conditions is detected, operation of the secondary collision brake is canceled.
·
The vehicle speed is below approximately 10 km/h. ·
Operation continues for a certain period of time. ·
After operating, the accelerator pedal is depressed a certain amount or more. |
Emergency Brake Signal
Operation conditions of the emergency brake signal
Emergency brake signal operates when all of the following conditions have been met:
·
The vehicle speed is approximately 55 km/h or more. ·
The brake pedal is depressed and the vehicle is judged to be rapidly braking based on the deceleration rate. |
Cancellation conditions of the emergency brake signal
If any one of the following conditions is met during emergency brake signal operation, emergency brake signal will be canceled.
·
When the hazard warning lights are turned on by operating the hazard warning signal switch. ·
The brake pedal is released. ·
The parking brake is applied. ·
The deceleration rate of the vehicle is judged not to be high. The vehicle is judged not to be rapidly braking based on the deceleration rate. |
SYSTEM CONTROL
The brake control system has the following controls:
| Control | Outline |
|---|---|
|
*1: Except destination package for Korea *2: Models with pre-collision system |
|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | The EBD utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, the EBD also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, helping ensure the vehicle's braking performance. |
| Traction Control (TRC) | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface. |
| Vehicle Stability Control (VSC) | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering. |
| Active Cornering Assist (ACA) | ACA performs brake control that applies braking force to the inside wheels when turning during periods of high acceleration, such as when the driver is depressing the accelerator pedal, generating a vehicle yaw moment. As a result, the tendency of the vehicle to understeer is suppressed, ensuring superior turning performance. |
| Steering Cooperative Control | The steering cooperative control performs cooperative control with the power steering ECU in order to provide steering assist in accordance with the operating conditions of the vehicle. |
| Trailer Sway Control | If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the engine output in order to suppress trailer sway. |
| Hill-start Assist Control | When starting uphill, this control maintains the brake hydraulic pressure on all 4 wheels in order to momentarily prevent the vehicle from descending backward. |
| Brake Hold Function | As the driver depresses the brake pedal and the vehicle comes to a stop, this function maintains the hydraulic pressure of the 4 wheels in order to keep the vehicle stopped. |
| Emergency Brake Signal*1 | In case of emergency braking, the emergency brake signal flashes the hazard warning lights to alert drivers in following vehicles. |
| Secondary Collision Brake*2 | After the airbags operate, this system automatically operates the brakes to suppress movement after a collision. |
FAIL-SAFE
If a malfunction is detected in the brake system, the fail-safe function operates. Depending on the type of malfunction, the fail-safe function informs the driver via warning indicators in the combination meter assembly and continues brake control via the use of non-malfunctioning parts. Also, when the system is not operating, the fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.
DIAGNOSIS
A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to Repair Manual.