OUTLINE
The following brake control functions are provided: Anti-lock Brake System (ABS), Electronic Brake force Distribution (EBD), brake assist, Traction Control (TRC), Vehicle Stability Control (VSC), Active Cornering Assist (ACA), steering cooperative control, trailer sway control, hill-start assist control and brake hold.
The skid control ECU processes signals from sensors and performs brake control.
An electronically controlled brake system is used for the brake hydraulic pressure control system. Also, the system performs regenerative brake cooperative control for the hybrid system to achieve superior low fuel consumption.
An emergency brake signal system is used. This system reduces the danger of rear-end collisions by automatically flashing the hazard warning lights during emergency braking to warn vehicles to the rear.*
*: Except destination package for Korea
A secondary collision brake system is used. This system lessens damage from a secondary collision by controlling the automatic brakes and stop light illumination after a collision occurs.*
*: Models with pre-collision system
The skid control ECU performs brake control using various driving assistance systems. For details, see each driving assistance system section.
Trail Mode is used. When Trail Mode is turned on, the system switches to the optimal control for 4WD/AWD control, brake control and motive force control. As a result, excellent driving performance on rough roads is achieved.*
*: 4WD/AWD models
MAIN FEATURES
Electronically Controlled Brake System
The electronically controlled brake system uses a sensor to detect the amount of brake pedal depression. Based on this, the skid control ECU calculates the braking force and the brake booster pump assembly and brake actuator control the brake fluid pressure of the 4 wheels.
The electronically controlled brake system cooperates with the hybrid system to optimally control the brake fluid pressure and regenerative braking. This enhances the efficiency of energy regeneration and improves fuel economy.
When the system is malfunctioning, brake control continues via the use of non-malfunctioning parts. Also, when the system is not operating, the brake fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.
Brake control apportions brake force to the hydraulic brake system and regenerative brake system at varying vehicle speeds as follows.
PRECAUTION
ABS
The ABS system cannot increase the performance limit of the tires. Always drive safely and be aware of the vehicle speed and distance to other vehicles.
Any non-standard components such as non-standard tires that are installed may have a negative effect on the ABS function.
When braking using ABS, the braking distance may be longer than models without ABS in the following conditions:
When driving on a dirt road or a road covered with fresh snow
When using tire chains
When driving over a joint in the road surface
When driving on a rough road such as an unpaved or stone-paved road
Brake Assist
Brake assist cannot increase the performance limit of the fundamental brake system. Always drive safely and be aware of the vehicle speed and distance to other vehicles.
TRC, VSC
The TRC and VSC systems ensure traction and vehicle stability. Do not disable the TRC and VSC functions unless necessary.
The TRC and VSC systems cannot increase the performance limit of the tires. Always drive the vehicle carefully in conditions in which drive wheel traction or vehicle stability may be lost.
Hill-start Assist Control
Hill-start assist control is not intended to keep the vehicle stationary on a hill for a prolonged period. As hill-start assist control only prevents the vehicle from rolling backwards for 2 seconds after the brake pedal is released, perform start-off within this period.
When hill-start assist control is operating and the power switch is turned off, hill-start assist control will be canceled without warning.
Hill-start assist control prevents the vehicle from rolling backwards by controlling the brake force to the 4 wheels. However, the vehicle may not remain stationary when on an extremely steep slope or a low friction surface such as ice.
Active Cornering Assist (ACA)
Active Cornering Assist (ACA) cannot increase the performance limit or innate maneuverability of the vehicle itself.
Do not overly rely on Active Cornering Assist (ACA). Active Cornering Assist (ACA) may not operate effectively when accelerating down slopes or driving on slippery road surfaces.
When Active Cornering Assist (ACA) frequently operates, Active Cornering Assist (ACA) may temporarily stop operating to ensure proper operation of the brakes, TRC and VSC.
Brake Hold
The brake hold is not for parking the vehicle for a long period of time in the same way as the parking brake.
If brake hold control does not operate even when the vehicle stops, depress the brake pedal again firmly to stop the vehicle. If the vehicle still does not stop, confirm the conditions for brake hold control to operate.
When the power switch is turned off during brake hold operation, control stops.
This function may not stop the vehicle on steep slopes and slippery roads.
Trail Mode
Trail Mode is not intended to expand the limits of the vehicle. Thoroughly check the road conditions and drive with caution.
Trail Mode may not be effective enough depending on the road conditions (pitch, slipperiness and undulations). Thoroughly check the road conditions before driving.
Trail Mode controls the vehicle so that the motive force can be maximized to improve driveability on rough roads. Therefore, the fuel economy will not be as efficient as when driving without Trail Mode.
Only use Trail Mode when driving on rough roads, and turn Trail Mode off at all other times.