FUNCTION OF MAIN COMPONENTS
The main components in the airbag system have the following functions:
| Components | Function | |
|---|---|---|
|
*1: Destination package for Korea *2: Models with rear pretensioner squib *3: Models with airbag cut off switch cylinder *4: HV models *5: Gasoline models with automatic transaxle *6: Destination package for Korea or models with airbag cut off switch cylinder with climate control seat system. *7: Destination package for Korea or models with airbag cut off switch cylinder without climate control seat system. |
||
| Driver Airbag (Horn Button Assembly) | Used as supplements to the seat belts to help reduce impact to the occupants. | |
| Front Passenger Airbag (Instrument Panel Passenger without Door Airbag Assembly) | ||
| Driver Knee Airbag (Lower No. 1 Instrument Panel Airbag Assembly) | ||
| Front Passenger Seat Cushion Airbag (Front Seat Cushion Airbag Assembly RH)*1 | ||
| Driver Side Airbag (Front Seat Airbag Assembly) | ||
| Front Passenger Side Airbag (Front Seat Airbag Assembly) | ||
| Curtain Shield Airbag Assembly LH | ||
| Curtain Shield Airbag Assembly RH | ||
| Front Seat Outer Belt Assembly LH
·
Seat Belt Pretensioner |
Used to help reduce impact to the occupants. | |
| Front Seat Outer Belt Assembly RH
·
Seat Belt Pretensioner |
||
| Rear Seat Outer Belt Assembly LH*2
·
Seat Belt Pretensioner |
||
| Rear Seat Outer Belt Assembly RH*2
·
Seat Belt Pretensioner |
||
| Spiral Cable Sub-assembly | Transmits ignition signals from the airbag ECU to the SRS driver airbag. | |
| Seat Position Airbag Sensor*1 | Detects the slide position of the driver seat. | |
| Front Airbag Sensor LH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Front Airbag Sensor RH | ||
| Side Airbag Pressure Sensor LH | Detects deformation of the front doors during a side collision using the pressure sensor and sends signals for the airbag ECU to determine if deployment of SRS components is necessary. | |
| Side Airbag Pressure Sensor RH | ||
| Floor Side Airbag Sensor LH | Based on the deceleration of the vehicle during a side or rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Floor Side Airbag Sensor RH | ||
| Steering Sensor | Sends steering angle signals to the airbag ECU via CAN communication. | |
| Front Occupant Classification Sensor*1 | The output values of this sensor, which vary in accordance with the distortion that acts on the brackets, are output to the occupant detection ECU. | |
| Rear Occupant Classification Sensor*1 | ||
| Airbag Cut Off Switch Cylinder Sub-assembly*3 | Suspends the SRS front passenger airbag operation. | |
| Driver Seat Belt Buckle Switch (Front Seat Inner Belt Assembly)*1 | Detects if the driver seat belt is fastened. | |
| Front Passenger Seat Belt Buckle Switch (Front Seat Inner Belt Assembly)*1 | Detects if the front passenger seat belt is fastened. | |
| Airbag ECU (Airbag Sensor Assembly) | ·
In the event of a frontal collision, the airbag ECU receives signals from either of the front airbag sensors. The airbag ECU receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU. After receiving a signal from at least one of the front airbag sensors and the safing sensor, the airbag ECU determines whether the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS front seat cushion airbag*1, SRS curtain shield airbags and front and rear*2 seat belt pretensioners should be deployed. The airbag ECU also diagnoses system malfunctions. ·
In the event of a side or rear side collision, the airbag ECU receives signals from the side airbag pressure sensor, floor side airbag sensor or No. 2 side airbag sensor assembly. The airbag ECU receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag ECU. After receiving a signal from at least one of the side sensors and the safing sensor, the airbag ECU determines whether the SRS driver and front passenger side airbags, SRS curtain shield airbags and seat belt pretensioners should be deployed. The airbag ECU also diagnoses system malfunctions. |
|
| Occupant Detection ECU*1 | Judges whether the front passenger seat is occupied based on signals from the 2 occupant classification sensors and the front passenger seat belt buckle switch. | |
| Hybrid Vehicle Control ECU*4 | Sends shift position signals and the operation status of the hybrid control system to the airbag ECU via CAN communication. | |
| ECM | Sends engine speed and shift position signals*5 and the operation status of the engine control system to the airbag ECU via CAN communication. | |
| Skid Control ECU | Sends vehicle speed signals, brake pedal operation signals and the operation status of the brake control system to the airbag ECU via CAN communication. | |
| Combination Meter Assembly | SRS Warning Indicator | Turns on to alert the driver when the airbag ECU detects a malfunction in the SRS airbag system. |
| Multi-information Display | Displays a warning message to inform the driver of a malfunction in the SRS airbag system. | |
| Buzzer | Sounds to warn the driver of a malfunction in the SRS airbag system. | |
| Refreshing Seat Switch*6,
Telltale Light Assembly*7 |
AIRBAG ON Indicator Light | Turns on to inform the driver when the occupant detection ECU has put the SRS front passenger airbag into an active state. |
| AIRBAG OFF Indicator Light | ·
Turns on to inform the driver when the occupant detection ECU has put the SRS front passenger airbag into an inactive state. ·
Turns on to alert the driver when the airbag ECU detects a malfunction in the occupant classification system. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
OPERATING CONDITION
Frontal Collision
Deceleration sensors used for the SRS airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag ECU sends a deployment signal to each SRS airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag ECU and front airbag sensors. Frontal collision signals are used to deploy the SRS airbags and activate the seat belt pretensioners as indicated in the table below.
If the severity of the collision is particularly high, the SRS curtain shield airbags LH and RH are deployed.
Side Collision
The SRS side airbag and SRS curtain shield airbag on the side of the collision are deployed and the front and rear*1 seat belt pretensioners on the side of the collision are activated based on signals from the side airbag pressure sensor, floor side airbag sensor and airbag ECU.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed*2 and the front and rear*1 seat belt pretensioners on the side opposite the collision are activated.
*1: Models with rear pretensioner squib
*2: Destination package for Korea
Roll Over (Destination Package for Korea)
The SRS curtain shield airbags LH and RH are deployed and the front and rear seat belt pretensioners are activated based on signals that show the vehicle's roll angle and rotation speed.
SYSTEM CONTROL
Frontal Collision (Destination Package for Korea)
There are 5 SRS airbags which deploy in the event of a frontal collision: the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS front passenger seat cushion airbag, SRS curtain shield airbag. These SRS airbags deploy simultaneously. The SRS driver airbag and SRS front passenger airbag use dual-stage control. In addition, the seat belt pretensioners contained in the front seat outer belt assemblies LH and RH and the rear seat outer belt assemblies LH and RH are also activated.
The airbag ECU detects the information in the table below from various sources in order to activate the dual-stage control.
| Airbag | Information | Source |
|---|---|---|
| Driver | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU |
| Driver Seat Position | Seat Position Airbag Sensor | |
| Seat Belt Condition | Driver Seat Belt Buckle Switch (Non-contact Type) | |
| Front Passenger | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag ECU |
| Occupant Detection | 2 Occupant Classification Sensors (Connected to the airbag ECU through the occupant detection ECU.) | |
| Seat Belt Condition | Front Passenger Seat Belt Buckle Switch (Non-contact Type) (Connected to the airbag ECU through the occupant detection ECU.) |
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag ECU. The airbag ECU causes the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag and SRS seat cushion airbag to deploy. Additionally, the airbag ECU activates the front and rear seat belt pretensioners.
If the severity of the collision is particularly high, the SRS curtain shield airbag LH and RH are deployed.
Frontal Collision (Except Destination Package for Korea)
There are 4 SRS airbags which deploy in the event of a frontal collision: the SRS driver airbag, SRS front passenger airbag, SRS driver knee airbag, SRS curtain shield airbag. These SRS airbags deploy simultaneously. In addition, the seat belt pretensioners contained in the front seat outer belt assemblies LH and RH and the rear seat outer belt assemblies LH and RH are also activated.
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag ECU. The airbag ECU causes the SRS driver airbag, SRS front passenger airbag and SRS driver knee airbag to deploy. Additionally, the airbag ECU activates the front and rear* seat belt pretensioners.
If the severity of the collision is particularly high, the SRS curtain shield airbag LH and RH are deployed.
*: Models with rear pretensioner squib
Side Collision
There are 2 SRS airbags which deploy in the event of a side collision: the SRS side airbag and SRS curtain shield airbag on the side of the collision. These SRS airbags deploy simultaneously. Additionally, at the same time, the front and rear*1 seat belt pretensioners on the side of the collision are also activated.
For a side collision, if the side airbag pressure sensor, No. 2 side airbag sensor assembly and floor side airbag sensor detect an impact, it informs the airbag ECU. The airbag ECU causes the SRS side airbag and SRS curtain shield airbag on the side of the collision to deploy simultaneously, and activates the front and rear*1 seat belt pretensioners on the side of the collision.
If the severity of the collision is particularly high, the SRS curtain shield airbag on the side opposite the collision is deployed*2 and the front and rear*1 seat belt pretensioners on the side opposite the collision are activated.
*1: Models with rear pretensioner squib
*2: Destination package for Korea
Roll Over (Destination Package for Korea)
If the vehicle is tilted and rolls over, the airbag ECU activates the SRS curtain shield airbags LH and RH and seat belt pretensioners for the driver, front passenger and rear passengers based on signals that show the vehicle's roll angle and rotation speed.
If the vehicle rolls over in a side collision, the airbag ECU causes the SRS side airbag and SRS curtain shield airbag on the side of the collision to deploy simultaneously, and activates the front and rear seat belt pretensioners on the side of the collision based on signals from the side airbag pressure sensor, floor side airbag sensor and No. 2 side airbag sensor assembly. Meanwhile, the airbag ECU activates the SRS curtain shield airbag on the side opposite the collision and the front and rear seat belt pretensioners on the side opposite the collision, based on lateral deceleration and rotation speed signals.
Primary Check Illumination Control
After the power switch or ignition switch is turned to ON, the airbag ECU illuminates the SRS warning indicator in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of SRS airbags is prohibited and a diagnosis of the airbag ECU is performed. If a malfunction is detected during the primary check, the SRS warning indicator will remain on even after 6 seconds have elapsed.
After the power switch or ignition switch is turned to ON, the airbag ECU operates the front passenger airbag ON/OFF indicator lights as shown below to check for an open in the indicator light circuits.
DIAGNOSIS
If the airbag ECU detects a malfunction in the SRS airbag system, the airbag ECU stores the malfunction data in memory in addition to illuminating the SRS warning indicator.
The airbag ECU outputs malfunction data and 5-digit Diagnostic Trouble Codes (DTCs) to the Global TechStream (GTS).
The 5-digit DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag ECU will turn on the SRS warning indicator. However, unlike an ordinary malfunction, a DTCs will not be stored. The SRS warning indicator cannot be manually turned off. It is necessary to replace the airbag ECU with a new one.