CHECK CUSTOMIZE PARAMETERS
The operation check below is based on the non-customized initial condition of the vehicle.
CHECK PUSH-BUTTON START FUNCTION (except Manual Transaxle)
Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off. With the shift state park (P), check that the key indicator display is displayed when the brake pedal is depressed. Check that the engine starts when the engine switch is pressed after the key indicator display is displayed in the combination meter assembly.
While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the engine switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.
With the shift state park (P), check that the steering lock operates when a door is opened.
| *a | Inspection Point |
Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Perform this inspection for both inspection points.
| *a | Inspection Point |
Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).
Perform this inspection for both inspection points.
| *a | Inspection Point |
Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).
Perform the inspection for both inspection points.
CHECK PUSH-BUTTON START FUNCTION (for Manual Transaxle)
Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off, check that the key indicator display is displayed when the clutch pedal is depressed. Check that the engine starts when the engine switch is pressed after the key indicator display is displayed in the combination meter assembly.
While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the engine switch is pressed with the clutch pedal released: off → on (ACC) → on (IG) → off.
Check that the steering lock operates when a door is opened.
| *a | Inspection Point |
Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Perform the inspection for both inspection points.
| *a | Inspection Point |
Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).
Perform this inspection for both inspection points.
| *a | Inspection Point |
Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).
Perform the inspection for both inspection points.
CHECK POWER SOURCE MODE CHANGING FUNCTION (except Manual Transaxle)
Check that the power source mode changes according to the chart below.
| Shift Position | Brake Pedal | Power Source Mode when Engine Switch Pressed |
|---|---|---|
| Park (P) selected | Released | Off → on (ACC) → on (IG) → off |
| Park (P) selected | Depressed | Off → engine starts |
| Park (P) selected | Depressed | On (ACC) → engine starts |
| Park (P) selected | Depressed | On (IG) → engine starts |
| Park (P) selected | Released / Depressed | Engine running → off |
| Park (N) selected | Released | Off → on (ACC) → on (IG) → on (ACC) |
| Park (N) selected | Depressed | Off → engine starts |
| Park (N) selected | Depressed | On (ACC) → engine starts |
| Park (N) selected | Depressed | On (IG) → engine starts |
| Park (N) selected | Released / Depressed | Engine running → on (ACC) |
| Park (P) or (N) not selected | Released | On (ACC) → on (IG) → on (ACC) |
| Park (P) or (N) not selected | Depressed | Off → on (IG) |
| Park (P) or (N) not selected | Depressed | On (ACC) → on (IG) |
| Park (P) or (N) not selected | Released / Depressed | Engine running → on (ACC) |
CHECK POWER SOURCE MODE CHANGING FUNCTION (for Manual Transaxle)
Check that the power source mode changes according to the chart below.
| Clutch Pedal | Power Source Mode when Engine Switch Pressed |
|---|---|
| Released | Off → on (ACC) → on (IG) → off |
| Depressed | Off → engine starts |
| Depressed | On (ACC) → engine starts |
| Depressed | On (IG) → engine starts |
| Released / Depressed | Engine running → off |
CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION
Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
Check that the entry and start system does not operate while in transmitter battery saving mode.
To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.
CHECK ENTRY CANCEL FUNCTION
Cancel the entry and start system and check that all the functions of the entry and start system no longer operate.
While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless function, and the engine can be started by holding the electrical key transmitter sub-assembly near the engine switch.
CHECK KEY DIAGNOSTIC MODE
With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the buzzer.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Inspect the appropriate item according to the following table.
| Tester Display | Inspection Item |
|---|---|
| [CH1/CH2] Overhead + Driver Side*1 | w/ Entry Function:
Front door outside handle assembly (electrical key antenna) (for Driver Door) |
| [CH1] Overhead + Driver Side*1 | |
| [CH2] Overhead + Driver Side*1 | |
| [CH1/CH2] Overhead + Passenger Side*2 | w/ Entry Function:
Front door outside handle assembly (electrical key antenna) (for Front Passenger Door) |
| [CH1] Overhead + Passenger Side*2 | |
| [CH2] Overhead + Passenger Side*2 | |
| [CH1/CH2] Overhead + Front Room*3 | No. 1 indoor electrical key antenna assembly (front floor) |
| [CH1] Overhead + Front Room*3 | |
| [CH2] Overhead + Front Room*3 | |
| [CH1/CH2] Overhead + Rear Room*4 | No. 2 indoor electrical key antenna assembly (rear floor) |
| [CH1] Overhead + Rear Room*4 | |
| [CH2] Overhead + Rear Room*4 | |
| [CH1/CH2] Overhead + Back Door*5 | w/ Entry Function:
Electrical key antenna (outside luggage compartment) |
| [CH1] Overhead + Back Door*5 | |
| [CH2] Overhead + Back Door*5 | |
| [CH1/CH2] Luggage + Back Door (inside)/Rear2*6 | No. 1 indoor electrical key antenna assembly (inside luggage compartment) |
| [CH1] Luggage + Back Door (inside)/Rear2*6 | |
| [CH2] Luggage + Back Door (inside)/Rear2*6 | |
| [CH1/CH2] Immobiliser Amp*7 | Amplifier (engine switch) |
| [CH1] Immobiliser Amp*7 | |
| [CH2] Immobiliser Amp*7 |
[CH1]: Channel 1 is set.
[CH2]: Channel 2 is set.
[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.
*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.
Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the buzzer sounds.
The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
w/ Entry Function:
*1: Front door outside handle assembly (for Driver Door)
Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.
*2: Perform the same inspection for the front passenger door.
| *a | Inspection Point |
*3: No. 1 indoor electrical key antenna assembly (front floor)
Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.
| *a | Inspection Point |
*4: No. 2 indoor electrical key antenna assembly (rear floor)
Place the electrical key transmitter sub-assembly on the rear seat cushion.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
w/ Entry Function:
*5: Electrical key antenna (outside luggage compartment)
Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.
| *a | Inspection Point |
*6: No. 1 indoor electrical key antenna assembly (inside luggage compartment)
Place the electrical key transmitter sub-assembly on the luggage room floor.
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
*7: Amplifier (engine switch)
While facing the logo side of the electrical key transmitter sub-assembly toward the engine switch, hold the transmitter near the engine switch.