Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2282 Vehicle Speed Signal Malfunction The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*)
·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 25 km/h (16 mph) or more for 20 seconds, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.


B2283 Vehicle Speed Sensor Malfunction Vehicle speed signal malfunction is detected (excessive deceleration is detected). (1-trip detection logic*)
·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Drive the vehicle at a vehicle speed of 50 km/h (31 mph) or more for 10 seconds.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be turned from on (IG) to off.


-
B2283
·

The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine will not start.


Steering lock motor operation is prohibited.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Power Supply Condition


Combination Meter
·

Vehicle Speed Meter



WIRING DIAGRAM

B532427E04
4.208,1.583 7.125,2.531 2.917,0.948 10 false Certification ECU (Smart Key ECU Assembly) 0.375,1.521 0.74,1.844 0.365,0.323 10 false G18 4.625,0.833 4.99,1.156 0.365,0.323 10 false 19 4.875,0.833 5.24,1.156 0.365,0.323 10 false SPD 5.042,0.448 5.406,0.771 0.365,0.323 10 false +B 6.104,1.167 6.469,1.49 0.365,0.323 10 false E 5.625,0.906 5.99,1.229 0.365,0.323 10 false IC 6.292,1.073 6.656,1.396 0.365,0.323 10 false 18 0.365,1.667 3.281,2.615 2.917,0.948 10 false Combination Meter Assembly 2.031,0.823 2.396,1.146 0.365,0.323 10 false 36 1.75,0.823 2.115,1.146 0.365,0.323 10 false +S 4.219,1.417 4.583,1.74 0.365,0.323 10 false G54 4.719,3.552 5.823,3.896 1.104,0.344 10 false ECM 4.719,3.385 5.823,3.729 1.104,0.344 10 false A24 4.854,2.646 5.219,2.969 0.365,0.323 10 false SPD 0.438,3.344 1.542,3.688 1.104,0.344 10 false C33 0.448,3.469 2.719,3.823 2.271,0.354 10 false Transmission Control ECU*1 4.635,5.104 5.74,5.448 1.104,0.344 10 false H6 4.635,5.25 6.906,5.604 2.271,0.354 10 false Telematics Transceiver*2 4.688,7.094 6.958,7.448 2.271,0.354 10 false Navigation ECU*4 0.521,5.302 3.208,5.75 2.688,0.448 10 false Radio and Display Receiver Assembly*3 4.688,6.969 5.792,7.313 1.104,0.344 10 false H7 0.521,5.177 1.625,5.521 1.104,0.344 10 false G3 0.49,6.958 1.594,7.302 1.104,0.344 10 false M3 0.479,7.083 3.24,7.385 2.76,0.302 10 false Stereo Component Amplifier Assembly*5 1.646,2.656 2.01,2.979 0.365,0.323 10 false SPD 1.656,4.469 2.021,4.792 0.365,0.323 10 false SPD 4.875,4.49 5.469,4.813 0.594,0.323 10 false SPDP 4.885,6.271 5.25,6.594 0.365,0.323 10 false SPD 1.656,6.26 2.021,6.583 0.365,0.323 10 false SPD 0.615,8.375 3.323,8.75 2.708,0.375 10 false : CAN Communication Line 3.125,7.604 5.833,7.979 2.708,0.375 10 false *1: except Manual Transaxle 3.125,7.917 5.833,8.292 2.708,0.375 10 false *2: w/ Telematics Transceiver 3.135,8.229 5.844,8.604 2.708,0.375 10 false *3: for Radio and Display Receiver 5.25,7.5 7.156,7.958 1.906,0.458 10 false *4: w/ Navigation System 5.25,7.906 7.156,8.365 1.906,0.458 10 false *5: for 9 Speakers 2.042,2.521 2.354,2.719 0.313,0.198 10 false 42 4.625,2.531 4.938,2.729 0.313,0.198 10 false 42 2.042,4.344 2.302,4.531 0.26,0.188 10 false 27 4.615,4.344 4.875,4.531 0.26,0.188 10 false 10 2.031,6.125 2.292,6.313 0.26,0.188 10 false 11 4.677,6.146 4.938,6.333 0.26,0.188 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 409 23
HINT:

Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the GTS.


OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Speed Signal
50003 223 16
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G18 combination meter assembly connector.


c.

Disconnect the A24 ECM connector.


d.

except Manual Transaxle:

Disconnect the C33 transmission control ECU connector.


e.

w/ Telematics Transceiver:

Disconnect the H6 telematics transceiver connector.


f.

for Radio and Display Receiver:

Disconnect the G3 radio and display receiver assembly connector.


g.

w/ Navigation System:

Disconnect the H7 navigation ECU connector.


h.

for 9 Speakers:

Disconnect the M3 stereo component amplifier assembly connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-36 (+S) - G54-19 (SPD) Always Below 1 Ω
G18-36 (+S) or G54-19 (SPD) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the G18 combination meter assembly connector.


c.

Using an oscilloscope, check the waveform.

B424430C50
1.927,0.417 2.344,0.667 0.417,0.25 2.854,2.115 2.604,2.115 2.604,2.115 2.604,1.365 true 2.771,2.365 2.521,2.365 2.521,2.365 2.521,1.365 true 0.104,0.167 0.417,0.365 0.313,0.198 10 false *a 2.021,0.448 2.333,0.646 0.313,0.198 10 false G54 2.917,2.052 3.229,2.25 0.313,0.198 10 false E 2.813,2.302 3.219,2.5 0.406,0.198 10 false SPD 6.573,1.49 6.958,1.698 0.385,0.208 10 false GND 4.302,0.406 4.615,0.604 0.313,0.198 10 false *b
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition
G54-19 (SPD) - G54-18 (E) Vehicle being driven at approximately 5 km/h (3 mph) 5 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)


HINT:

The wavelength becomes shorter as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)