Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

w/o Occupant Classification System:

If the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM will store this DTC.


w/ Occupant Classification System:

If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM will store this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery
w/o Occupant Classification System:

The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).


w/ Occupant Classification System:

The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*).


w/o Occupant Classification System
·

Harness or connector

·

ID code box (immobiliser code ECU)

·

ECM


w/ Occupant Classification System
·

Harness or connector

·

Certification ECU (smart key ECU assembly)

·

ECM


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

w/o Occupant Classification System:
B499509E10
0.479,1.885 3.115,2.25 2.635,0.365 10 false ID Code Box (Immobiliser Code ECU) 0.49,1.729 0.958,1.969 0.469,0.24 10 false G57 1.781,0.729 2.25,0.969 0.469,0.24 10 false EFIO 2.177,0.729 2.646,0.969 0.469,0.24 10 false 4 5.083,1.906 5.563,2.125 0.479,0.219 10 false ECM 5.094,1.698 6.021,1.906 0.927,0.208 10 false A24 5.125,0.75 5.594,0.99 0.469,0.24 10 false IMI 4.854,0.729 5.563,0.938 0.708,0.208 10 false 26 6.354,0.385 6.823,0.625 0.469,0.24 10 false +B

w/ Occupant Classification System:
C375434E08
0.479,1.885 3.115,2.25 2.635,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.49,1.729 0.958,1.969 0.469,0.24 10 false A15 1.781,0.729 2.25,0.969 0.469,0.24 10 false EFIO 2.177,0.729 2.646,0.969 0.469,0.24 10 false 4 5.083,1.906 5.563,2.125 0.479,0.219 10 false ECM 5.094,1.698 6.021,1.906 0.927,0.208 10 false A24 5.125,0.75 5.594,0.99 0.469,0.24 10 false IMI 4.854,0.729 5.563,0.938 0.708,0.208 10 false 26 6.354,0.385 6.823,0.625 0.469,0.24 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

*1: w/o Occupant Classification System

*2: w/ Occupant Classification System




HINT:

When DTC B279A12 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Proceed to
w/o Occupant Classification System
w/ Occupant Classification System



w/o Occupant Classification System

2.CHECK CONNECTION OF CONNECTOR

w/ Occupant Classification System

5.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B



A

3.CHECK ECM (TERMINAL EFIO)

B

CONNECT CONNECTORS PROPERLY

3.CHECK ECM (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

C379327C40
3.271,0.042 3.646,0.229 0.375,0.188 3.344,0.833 2.844,1.26 2.844,1.26 2.698,1.26 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 2.573,0.25 2.885,0.406 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.875,2.99 1.188,3.146 0.313,0.156 10 false GND 3.344,0.063 3.656,0.219 0.313,0.156 10 false G57 2.344,1.177 2.76,1.375 0.417,0.198 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G57-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform C



A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

B

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the A24 ECM connector.


b.

Disconnect the G57 ID code box (immobiliser code ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-4 (EFIO) - A24-26 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B



A

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

B

CONNECT CONNECTORS PROPERLY

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B473424C13
2.042,0.25 2.458,0.5 0.417,0.25 3.021,4.594 3.208,4.594 3.208,4.594 3.208,4.073 false 3.573,4.594 3.385,4.594 3.385,4.594 3.385,4.073 false 2.781,2.125 2.594,2.125 2.594,2.125 2.594,1.063 true 0.104,0.271 0.417,0.427 0.313,0.156 10 false *a 3.26,3.042 3.573,3.198 0.313,0.156 10 false *b 2.885,4.5 3.198,4.656 0.313,0.156 10 false *c 3.594,4.5 3.906,4.656 0.313,0.156 10 false *d 2.115,0.292 2.427,0.448 0.313,0.156 10 false A15 0.896,4.021 1.49,4.302 0.594,0.281 10 false GND 2.833,2.031 3.427,2.313 0.594,0.281 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A15-4 (EFIO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A24 ECM connector.


b.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-4 (EFIO) - A24-26 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR