Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

WIRING DIAGRAM

w/o Occupant Classification System:
B501256E20
5.344,2.938 6.25,3.125 0.906,0.188 10 false A24 5.333,3.146 6.052,3.406 0.719,0.26 10 false ECM 6.656,1.604 7.115,1.802 0.458,0.198 10 false +B 5.448,0.583 5.906,0.781 0.458,0.198 10 false IMO 5.438,1.917 5.896,2.115 0.458,0.198 10 false IMI 5.188,0.573 5.865,0.771 0.677,0.198 10 false 25 5.177,1.938 5.927,2.135 0.75,0.198 10 false 26 1.708,0.552 2.167,0.75 0.458,0.198 10 false EFII 1.635,1.948 2.094,2.146 0.458,0.198 10 false EFIO 2.052,0.563 2.51,0.76 0.458,0.198 10 false 3 2.052,1.917 2.51,2.115 0.458,0.198 10 false 4 0.344,2.917 0.802,3.115 0.458,0.198 10 false G57 0.333,3.094 2.625,3.313 2.292,0.219 10 false ID Code Box (Immobiliser Code ECU) 0.802,0.146 1.26,0.344 0.458,0.198 10 false +B

w/ Occupant Classification System:
C375433E12
5.344,2.938 6.25,3.125 0.906,0.188 10 false A24 5.333,3.146 6.052,3.406 0.719,0.26 10 false ECM 5.792,1.25 6.25,1.448 0.458,0.198 10 false +B 5.344,0.781 5.802,0.979 0.458,0.198 10 false IMO 5.302,1.729 5.76,1.927 0.458,0.198 10 false IMI 5.052,0.771 5.729,0.969 0.677,0.198 10 false 25 5.021,1.74 5.771,1.938 0.75,0.198 10 false 26 1.583,0.823 2.042,1.021 0.458,0.198 10 false EFII 1.521,1.729 1.979,1.927 0.458,0.198 10 false EFIO 1.969,0.802 2.427,1 0.458,0.198 10 false 3 1.979,1.729 2.438,1.927 0.458,0.198 10 false 4 0.281,2.802 0.74,3 0.458,0.198 10 false A15 0.281,2.979 2.594,3.438 2.313,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.688,0.25 1.146,0.448 0.458,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ID code box (immobiliser code ECU)*1, certification ECU (smart key ECU assembly)*2 or ECM, refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

*1: w/o Occupant Classification System

*2: w/ Occupant Classification System




PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Proceed to
w/o Occupant Classification System
w/ Occupant Classification System



w/o Occupant Classification System

2.CHECK FOR DTC

w/ Occupant Classification System

13.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical or Powertrain / Entry&Start or Engine / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)
a.

Enter the following menus: Powertrain / Engine / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser fuel cut OFF or ON OFF: Fuel cut off
ON: Fuel cut on
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts within 5 seconds of the engine switch being turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK ECM (TERMINAL EFII AND EFIO)
5.CHECK ECM (TERMINAL EFII AND EFIO)
a.

Using an oscilloscope, check the waveform.

B519883C07
3.344,0.042 3.75,0.219 0.406,0.177 4.75,0.25 4.583,0.25 4.583,0.25 3.583,0.917 true 3.333,0.917 2.667,0.417 2.667,0.417 2.5,0.417 true 3,3.646 3,4.229 3,4.229 2.833,4.229 true 3.167,3.635 3.167,4.219 3.167,4.219 3.333,4.219 true 3.583,5.698 3.583,6.135 3.583,6.135 3.75,6.135 true 3.417,5.688 3.417,6.26 3.417,6.26 3.583,6.26 true 2.26,0.094 2.573,0.25 0.313,0.156 10 false *a 2.656,4.146 2.969,4.302 0.313,0.156 10 false *b 3.354,4.146 3.667,4.302 0.313,0.156 10 false *c 3.646,6.208 3.958,6.365 0.313,0.156 10 false *d 3.667,7.375 3.979,7.531 0.313,0.156 10 false *e 1.375,2.427 1.688,2.583 0.313,0.156 10 false *f 1.375,4.448 1.688,4.604 0.313,0.156 10 false *g 2.417,4.646 2.729,4.802 0.313,0.156 10 false *h 3.031,2.698 3.344,2.854 0.313,0.156 10 false *i 3.458,4.615 3.771,4.771 0.313,0.156 10 false *j 1.458,6.49 1.771,6.646 0.313,0.156 10 false *k 4.802,0.156 5.417,0.354 0.615,0.198 10 false EFII 3.792,6.073 4.104,6.229 0.313,0.156 10 false *c 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 1.854,7.135 2.167,7.292 0.313,0.156 10 false *d 1.948,7.385 2.26,7.542 0.313,0.156 10 false *e 1.021,5.656 1.385,5.917 0.365,0.26 10 false GND 1.01,3.615 1.375,3.875 0.365,0.26 10 false GND 2.177,0.365 2.792,0.563 0.615,0.198 10 false EFIO 3.427,0.052 4.042,0.25 0.615,0.198 10 false G57 3.125,6.479 3.438,6.635 0.313,0.156 10 false *k
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f IMO Waveform
*g IMI Waveform *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G57-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform B)
G57-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform A and C)



Result:
Result Proceed to
Normal waveform A
Waveform A is not output, or has abnormal wavelength or shape B
Waveform B is not output, or has abnormal wavelength or shape C
Waveform C is not output, or has abnormal wavelength or shape D



A

6.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

D

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID WAS NOT REGISTERED)

NG

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G57 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-3 (EFII) - A24-25 (IMO) Always Below 1 Ω
G57-4 (EFIO) - A24-26 (IMI) Always Below 1 Ω
G57-3 (EFII) or A24-25 (IMO) - Other terminals and body ground Always 10 kΩ or higher
G57-4 (EFIO) or A24-26 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER RECOGNITION CODE
10.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

13.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical or Powertrain / Entry&Start or Engine / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

14.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)

B

14.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS)
a.

Enter the following menus: Powertrain / Engine / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser fuel cut OFF or ON OFF: Fuel cut off
ON: Fuel cut on
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts within 5 seconds of the engine switch being turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

16.CHECK ECM (TERMINAL EFII AND EFIO)
16.CHECK ECM (TERMINAL EFII AND EFIO)
a.

Using an oscilloscope, check the waveform.

B531283C03
2.25,0.229 2.708,0.479 0.458,0.25 2.719,1.042 1.938,1.823 1.938,1.823 1.771,1.823 true 3,3.646 3,4.229 3,4.229 2.833,4.229 true 3.167,3.635 3.167,4.219 3.167,4.219 3.333,4.219 true 3.583,5.698 3.583,6.135 3.583,6.135 3.75,6.135 true 3.417,5.688 3.417,6.26 3.417,6.26 3.583,6.26 true 2.792,1.052 1.875,1.958 1.875,1.958 1.708,1.958 true 0.25,0.24 0.563,0.396 0.313,0.156 10 false *a 2.656,4.146 2.969,4.302 0.313,0.156 10 false *b 3.354,4.146 3.667,4.302 0.313,0.156 10 false *c 3.646,6.208 3.958,6.365 0.313,0.156 10 false *d 3.667,7.375 3.979,7.531 0.313,0.156 10 false *e 1.375,2.427 1.688,2.583 0.313,0.156 10 false *f 1.375,4.448 1.688,4.604 0.313,0.156 10 false *g 2.417,4.646 2.729,4.802 0.313,0.156 10 false *h 3.031,2.698 3.344,2.854 0.313,0.156 10 false *i 3.458,4.615 3.771,4.771 0.313,0.156 10 false *j 1.458,6.49 1.771,6.646 0.313,0.156 10 false *k 1.406,1.896 2.021,2.094 0.615,0.198 10 false EFII 3.792,6.073 4.104,6.229 0.313,0.156 10 false *c 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 1.854,7.135 2.167,7.292 0.313,0.156 10 false *d 1.948,7.385 2.26,7.542 0.313,0.156 10 false *e 1.01,5.667 1.375,5.927 0.365,0.26 10 false GND 1,3.625 1.365,3.885 0.365,0.26 10 false GND 1.417,1.75 2.031,1.948 0.615,0.198 10 false EFIO 2.365,0.271 2.979,0.469 0.615,0.198 10 false A15 3.167,6.49 3.479,6.646 0.313,0.156 10 false *k
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f IMO Waveform
*g IMI Waveform *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
A15-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform B)
A15-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform A and C)



Result:
Result Proceed to
Normal waveform A
Waveform A is not output, or has abnormal wavelength or shape B
Waveform B is not output, or has abnormal wavelength or shape C
Waveform C is not output, or has abnormal wavelength or shape D



A

17.REGISTER ECU COMMUNICATION ID (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

D

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
17.REGISTER ECU COMMUNICATION ID (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER ENGINE STARTS
18.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID WAS NOT REGISTERED)

NG

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-3 (EFII) - A24-25 (IMO) Always Below 1 Ω
A15-4 (EFIO) - A24-26 (IMI) Always Below 1 Ω
A15-3 (EFII) or A24-25 (IMO) - Other terminals and body ground Always 10 kΩ or higher
A15-4 (EFIO) or A24-26 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.REGISTER RECOGNITION CODE
21.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

22.REGISTER ECU COMMUNICATION ID
22.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER ENGINE STARTS
23.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG