Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for Gasoline Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0370335 CRUISE CONTROL SYSTEM(for Gasoline Model) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for Gasoline Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. When the ECM receives the signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch ON and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

C408689E01
3.052,2.375 4.969,2.625 1.917,0.25 10 false Stop Light Switch Assembly 1.896,3.656 5.875,3.854 3.979,0.198 10 false Skid Control ECU (Brake Actuator Assembly) 3.021,5.115 4.969,5.479 1.948,0.365 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 5.479,3.635 7.01,4 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.365,3.208 4.906,3.448 0.542,0.24 10 false 41 1.906,3.49 2.448,3.729 0.542,0.24 10 false A39 0.458,0.594 1.469,0.792 1.01,0.198 10 false from J/B-B Fuse 0.281,1.375 1.75,1.688 1.469,0.313 10 false from IG2 NO.2 Relay 6.031,2.281 6.573,2.521 0.542,0.24 10 false ECM 4.344,0.729 4.594,0.969 0.25,0.24 10 false 3 3.563,0.625 3.781,0.865 0.219,0.24 10 false B 5.688,0.75 6.229,0.99 0.542,0.24 10 false STP 4.146,0.615 4.333,0.854 0.188,0.24 10 false L 5.708,1.531 6.25,1.771 0.542,0.24 10 false ST1- 3.573,1.396 3.792,1.635 0.219,0.24 10 false B 4.156,1.385 4.344,1.625 0.188,0.24 10 false L 3.573,1.813 3.958,2.042 0.385,0.229 10 false GND 6.031,2.104 6.573,2.344 0.542,0.24 10 false A24 4.344,1.531 4.594,1.771 0.25,0.24 10 false 5 5.406,0.75 5.656,0.99 0.25,0.24 10 false 21 5.396,1.521 5.646,1.76 0.25,0.24 10 false 22 3.375,1.938 3.625,2.177 0.25,0.24 10 false 2 2.406,0.781 3.417,0.979 1.01,0.198 10 false STOP 2.146,1.573 3.156,1.771 1.01,0.198 10 false ECU-IG2 NO.3 3.063,2.177 3.448,2.406 0.385,0.229 10 false A40 3.375,1.531 3.625,1.771 0.25,0.24 10 false 6 3.354,0.74 3.604,0.979 0.25,0.24 10 false 7 3.042,4.917 4.094,5.115 1.052,0.198 10 false G26*1, G27*2 6,4.979 6.542,5.219 0.542,0.24 10 false TCM*3 3.99,4.406 4.531,4.646 0.542,0.24 10 false STP 3.99,3.083 4.531,3.323 0.542,0.24 10 false STP 5.76,3.063 6.302,3.302 0.542,0.24 10 false STP1 5.75,4.406 6.292,4.646 0.542,0.24 10 false STP 4.354,4.531 4.896,4.771 0.542,0.24 10 false 4*1, 8*2 5.469,3.458 6.01,3.698 0.542,0.24 10 false M7 5.5,3.208 6.042,3.448 0.542,0.24 10 false 25 5.99,4.802 6.531,5.042 0.542,0.24 10 false C33 5.49,4.531 5.74,4.76 0.25,0.229 10 false 34 0.094,4.281 2.042,4.646 1.948,0.365 10 false *1: w/ Entry and Start System 0.115,4.708 2.063,5.073 1.948,0.365 10 false *2: w/o Entry and Start System 0.115,5.073 2.542,5.448 2.427,0.375 10 false *3: for Continuously Variable Transaxle 5.198,2.969 5.74,3.208 0.542,0.24 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A418954C27
1.5,0.25 1.917,0.5 0.417,0.25 1.146,1.833 1.396,1.333 true 1.781,1.844 2.031,1.344 true 2.25,1.208 2.667,0.458 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 0.958,1.854 1.417,2.052 0.458,0.198 10 false GND 1.729,1.854 2.188,2.052 0.458,0.198 10 false B 2.708,0.375 3.167,0.573 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A40 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-7 (B) - Body ground Always 11 to 14 V
A40-6 (B) - Body ground Ignition switch ON 11 to 14 V
A40-6 (B) - Body ground Ignition switch off Below 1 V



d.

Connect the A40 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A24 ECM connector.


c.

for Continuously Variable Transaxle:

Disconnect the C33 TCM connector.


d.

Disconnect the A40 stop light switch assembly connector.


e.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


f.

w/ Entry and Start System:

Disconnect the G26 shift control ECU connector.


g.

w/o Entry and Start System:

Disconnect the G27 shift control ECU connector.


h.

w/ Entry and Start System:

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-22 (ST1-) - A40-5 (L) Always Below 1 Ω
A24-21 (STP) - A40-3 (L) Always Below 1 Ω
A24-22 (ST1-) or A40-5 (L) - Body ground Always 10 kΩ or higher
A24-21 (STP) or A40-3 (L) - Body ground Always 10 kΩ or higher



j.

w/ Entry and Start System:

Connect the M7 certification ECU (smart key ECU assembly) connector.


k.

w/o Entry and Start System:

Connect the G27 shift control ECU connector.


l.

w/ Entry and Start System:

Connect the G26 shift control ECU connector.


m.

Connect the A39 skid control ECU (brake actuator assembly) connector.


n.

Connect the A40 stop light switch assembly connector.


o.

for Continuously Variable Transaxle:

Connect the C33 TCM connector.


p.

Connect the A24 ECM connector.


q.

Connect the cable from the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR