Home › Audio / Visual / Telematics › TELEMATICS › MAYDAY SWITCH › 2018.10–2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0370497 MAYDAY SWITCH G

TELEMATICS  MAYDAY SWITCH  INSPECTION  


PROCEDURE

Hide 1.REMOVE MAP LIGHT ASSEMBLY

Hide 2.INSPECT MAYDAY SWITCH (MAP LIGHT ASSEMBLY)

a.
E400129C01
0.958,1.854 1.323,1.854 1.323,1.854 1.323,1.323 true 2.552,1.885 2.313,1.885 2.313,1.885 2.313,1.313 true 0.083,0.063 0.292,0.26 0.208,0.198 10 false *a 2.604,1.802 3.01,1.979 0.406,0.177 10 false GND3 0.583,1.771 0.927,1.958 0.344,0.188 10 false SIG1
*a Component without harness connected
(Mayday Switch (Map Light Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
18 (SIG1) - 12 (GND3) Manual (SOS) switch not pressed 408 to 417 Ω
18 (SIG1) - 12 (GND3) Manual (SOS) switch pressed 81 to 83 Ω


If the result is not as specified, replace the mayday switch (map light assembly).


b.

Inspect the operation (red indicator)

i.
E400131C01
0.969,3.094 1.24,3.094 1.24,3.094 1.24,2.354 true 2.438,3.073 2.25,3.073 2.25,3.073 2.25,2.521 true 1.854,1.219 1.854,0.823 true 0.594,3.01 0.969,3.208 0.375,0.198 10 false IND1 2.5,3 2.948,3.198 0.448,0.198 10 false GND3 0.042,0.063 0.313,0.271 0.271,0.208 10 false *a 1.781,1.24 2.021,1.427 0.24,0.188 10 false *b
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
*b Two 1.5 V dry cell batteries


Check that each indicator illuminates when 2 dry cell batteries are connected to the map light assembly connector terminals as shown in the illustration.

OK:
Battery Connection Specified Condition
8 (IND1) - Battery positive (+)
12 (GND3) - Battery negative (-)
Red indicator comes on.


NOTICE:

Do not apply more than 3 V.


If the result is not as specified, replace the mayday switch (map light assembly).



c.

Inspect the operation (green indicator)

i.
E400130C01
1.833,1.208 1.833,0.823 true 0.885,3.031 1.073,3.031 1.073,3.031 1.073,2.531 true 2.448,3.021 2.24,3.021 2.24,3.021 2.24,2.542 true 0.052,0.052 0.323,0.281 0.271,0.229 10 false *a 1.76,1.26 2.01,1.458 0.25,0.198 10 false *b 2.51,2.938 2.958,3.135 0.448,0.198 10 false GND3 0.521,2.948 0.875,3.156 0.354,0.208 10 false IND2
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
*b Two 1.5 V dry cell batteries


Check that each indicator illuminates when 2 dry cell batteries are connected to the map light assembly connector terminals as shown in the illustration.

OK:
Battery Connection Specified Condition
19 (IND2) - Battery positive (+)
12 (GND3) - Battery negative (-)
Green indicator comes on.


NOTICE:

Do not apply more than 3 V.


If the result is not as specified, replace the mayday switch (map light assembly).



d.

Inspect the operation (HELP indicator)

i.
E400129C02
0.74,1.833 0.99,1.833 0.99,1.833 0.99,1.323 true 2.635,1.844 2.323,1.844 2.323,1.844 2.323,1.333 true 0.083,0.073 0.375,0.344 0.292,0.271 10 false *a 2.698,1.729 3.135,1.917 0.438,0.188 10 false GND3 0.354,1.75 0.729,1.948 0.375,0.198 10 false RRID
*a Component without harness connected
(Mayday Switch (Map Light Assembly))


Check that each indicator illuminates when auxiliary battery are connected to the mayday switch (map light assembly) connector terminals.

OK:
Auxiliary Battery Connection Specified Condition
20 (RRID) - Auxiliary battery positive (+)
12 (GND3) - Auxiliary battery negative (-)
HELP indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).



Hide 3.INSTALL MAP LIGHT ASSEMBLY