35572A
1.REMOVE TRANSMISSION CONTROL SHAFT LEVER
Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Remove the 2 bolts and park/neutral position switch assembly from the automatic transaxle case sub-assembly.
3.REMOVE REFILL PLUG
Remove the refill plug and gasket from the automatic transaxle case sub-assembly.
4.REMOVE OVERFLOW PLUG
Using a 10 mm socket hexagon wrench, remove the overflow plug and gasket from the transaxle housing.
35125C
5.REMOVE NO. 1 TRANSMISSION OIL FILLER TUBE
Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the transaxle housing.
32901C
6.REMOVE OIL COOLER UNION SUB-ASSEMBLY
| *1 | Oil Cooler Union Bolt |
Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.
Remove the oil cooler union bolt, 2 gaskets and oil cooler union sub-assembly from the automatic transaxle case sub-assembly.
32905
7.REMOVE NO. 1 OIL COOLER OUTLET TUBE SUB-ASSEMBLY
Using a 19 mm union nut wrench, remove the No. 1 oil cooler outlet tube sub-assembly from the automatic transaxle case sub-assembly.
Remove the O-ring from the No. 1 oil cooler outlet tube sub-assembly.
35151F
8.REMOVE TRANSMISSION CASE SIDE COVER
82125J
9.REMOVE TRANSMISSION WIRE
35410
10.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
89413N
11.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
89413S
12.REMOVE TRANSMISSION REVOLUTION SENSOR (NC)
13.INSPECT INPUT SHAFT END PLAY
35111C
14.REMOVE TRANSAXLE HOUSING
Remove the 20 bolts.
Using a plastic-faced hammer, tap on the circumference of the transaxle housing to remove it from the automatic transaxle case sub-assembly.
| *1 | Transaxle Case Gasket |
| *2 | O-ring |
Remove the 5 transaxle case gaskets from the front oil pump assembly.
Remove the O-ring from the automatic transaxle case sub-assembly.
35174
15.REMOVE TRANSAXLE HOUSING OIL SEPARATOR
Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.
35394
16.REMOVE TRANSMISSION OIL CLEANER MAGNET
Remove the 3 transmission oil cleaner magnets from the transaxle housing oil separator.
35394
17.INSPECT TRANSMISSION OIL CLEANER MAGNET
35882C
18.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
Remove the differential gear lube apply tube from the transaxle housing.
35847C
19.REMOVE TRANSMISSION LUBE APPLY TUBE
Remove the bolt and clamp from the transaxle housing.
Remove the transmission lube apply tube from the transaxle housing.
20.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case assembly from the automatic transaxle case sub-assembly.
35617F
21.REMOVE CLUTCH DRUM OIL SEAL RING
Remove the clutch drum oil seal ring from the front oil pump assembly.
35354
22.REMOVE OIL PUMP SPROCKET FRONT THRUST WASHER
Remove the oil pump sprocket front thrust washer from the transmission oil pump drive sprocket.
35781C
23.REMOVE TRANSMISSION DRIVE CHAIN
Remove the transmission drive chain together with the transmission oil pump drive sprocket and oil pump drive shaft sub-assembly from the front oil pump assembly.
To avoid damaging the bush of the front oil pump assembly, remove the transmission drive chain, transmission oil pump drive sprocket and oil pump drive shaft sub-assembly horizontally relative to the front oil pump assembly.
35355
24.REMOVE OIL PUMP SPROCKET REAR THRUST WASHER
Remove the oil pump sprocket rear thrust washer from the front oil pump assembly.
35409D
25.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY
Remove the bolt and manual detent spring sub-assembly from the front oil pump assembly.
26.REMOVE FRONT OIL PUMP ASSEMBLY
To avoid damaging the front oil pump assembly and transmission valve body assembly, when removing the front oil pump assembly, first remove the transmission valve body assembly.
Remove the 7 bolts and front oil pump assembly from the automatic transaxle case sub-assembly.
35737
27.REMOVE PLANETARY CARRIER THRUST WASHER
Remove the planetary carrier thrust washer from the C-3 and C-4 clutch assembly.
34610
28.REMOVE C-3 AND C-4 CLUTCH ASSEMBLY
Remove the C-3 and C-4 clutch assembly from the front planetary gear assembly.
29.INSPECT CLEARANCE OF C-3 CLUTCH
30.INSPECT CLEARANCE OF C-4 CLUTCH
35738
31.REMOVE NO. 2 PLANETARY CARRIER THRUST WASHER
Remove the No. 2 planetary carrier thrust washer from the front planetary gear assembly.
35719B
32.REMOVE PLANETARY SUN GEAR
Remove the planetary sun gear from the front planetary gear assembly.
35779A
33.REMOVE NO. 9 THRUST BEARING RACE
Remove the No. 9 thrust bearing race from the front planetary gear assembly.
35778A
34.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the front planetary gear assembly.
35778
35.REMOVE NO. 8 THRUST BEARING RACE
Remove the No. 8 thrust bearing race from the front planetary gear assembly.
35720
36.REMOVE FRONT PLANETARY GEAR ASSEMBLY
Remove the front planetary gear assembly from the front planetary ring gear.
37.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the front planetary ring gear.
35777
38.REMOVE NO. 7 THRUST BEARING RACE
Remove the No. 7 thrust bearing race from the front planetary gear assembly.
35720
39.INSPECT FRONT PLANETARY GEAR ASSEMBLY
35712E
40.REMOVE INPUT SHAFT OIL SEAL RING
Remove the 5 input shaft oil seal rings from the front planetary gear assembly.
Do not expand the gap of the input shaft oil seal rings excessively.
35749B
41.REMOVE REAR INPUT SHAFT OIL SEAL RING
Remove the 2 rear input shaft oil seal rings from the front planetary gear assembly.
Do not expand the gap of the rear input shaft oil seal rings excessively.
35743
42.REMOVE FRONT PLANETARY RING GEAR
Remove the front planetary ring gear with front planetary ring gear flange from the C-1 clutch assembly.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front planetary ring gear.
Be careful not to damage the front planetary ring gear and front planetary ring gear flange.
Remove the front planetary ring gear flange from the front planetary ring gear.
43.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-1 clutch assembly.
35776
44.REMOVE NO. 6 THRUST BEARING RACE
Remove the No. 6 thrust bearing race from the C-1 clutch assembly.
45.REMOVE C-1 CLUTCH ASSEMBLY
Remove the C-1 clutch assembly from the counter drive gear sub-assembly.
46.INSPECT CLEARANCE OF C-1 CLUTCH
35707D
47.REMOVE REAR PLANETARY SUN GEAR SUB-ASSEMBLY
Remove the No. 3 thrust bearing race from the rear planetary sun gear sub-assembly.
Using SST and a press, remove the rear planetary sun gear sub-assembly from the C-1 clutch assembly.
Remove the planetary sun gear sub-assembly from the rear planetary sun gear sub-assembly.
Remove the No. 4 thrust bearing race from the rear planetary sun gear sub-assembly.
Remove the thrust needle roller bearing from the rear planetary sun gear sub-assembly.
Remove the thrust bearing race from the rear planetary sun gear sub-assembly.
35706V
48.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY
35707D
49.INSPECT REAR PLANETARY SUN GEAR SUB-ASSEMBLY
50.REMOVE C-1 CLUTCH ASSEMBLY
Remove the C-1 clutch assembly from the sun gear input hub sub-assembly.
51.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the sun gear input hub sub-assembly.
35775K
52.REMOVE NO. 5 THRUST BEARING RACE
Remove the No. 5 thrust bearing race from the sun gear input hub sub-assembly.
53.REMOVE TOLERANCE RING
Using a screwdriver with its tip wrapped in protective tape, remove the tolerance ring from the clutch drum sub-assembly.
Be careful not to damage the clutch drum sub-assembly.
35633
54.REMOVE FRONT CLUTCH CLUTCH DISC
Using a screwdriver with its tip wrapped in protective tape, remove the snap ring from the clutch drum sub-assembly.
Be careful not to damage the clutch drum sub-assembly.
| *1 | Forward Clutch Flange |
| *2 | Front Clutch Clutch Disc |
| *3 | Forward Multiple Disc Clutch Clutch Plate |
| *a | Snap Ring Side |
| *b | Front Clutch Clutch Disc Side |
Remove the forward clutch flange, 4 front clutch clutch discs and 4 forward multiple disc clutch clutch plates from the clutch drum sub-assembly.
35633
55.INSPECT FRONT CLUTCH CLUTCH DISC
35668
56.REMOVE NO. 1 CLUTCH BALANCER
Place SST on the No. 1 clutch balancer and compress the rear clutch piston return compression spring with a press.
Do not compress the rear clutch piston return compression spring excessively.
Using SST, remove the snap ring from the clutch drum sub-assembly.
Remove the No. 1 clutch balancer from the forward clutch piston.
35650B
57.REMOVE REAR CLUTCH PISTON RETURN COMPRESSION SPRING
Remove the rear clutch piston return compression spring from the forward clutch piston.
35612B
58.REMOVE FORWARD CLUTCH PISTON
Set the front planetary gear assembly on the clutch drum sub-assembly.
|
Cover Oil Hole |
Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole of the front planetary gear assembly to separate the forward clutch piston from the clutch drum sub-assembly.
Be careful as ATF may spray when applying compressed air.
Make sure to cover the ATF hole shown in the illustration.
Remove the forward clutch piston from the clutch drum sub-assembly.
Remove the O-ring from the clutch drum sub-assembly.
Remove the D-ring from the clutch drum sub-assembly.
35506
59.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY
Remove the bolt.
Align the cutouts of the manual valve lever sub-assembly and manual valve lever shaft sub-assembly, and remove the manual valve lever shaft sub-assembly.
Rotating the manual valve lever shaft sub-assembly to the area shown in the illustration will align the cutouts.
Remove the O-ring from the manual valve lever shaft sub-assembly.
35505
60.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY
Remove the manual valve lever sub-assembly from the automatic transaxle case sub-assembly.
35596
61.REMOVE PAWL STOPPER PLATE
Remove the 2 bolts and pawl stopper plate from the automatic transaxle case sub-assembly.
35506J
62.REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING
Remove the manual valve lever shaft retainer spring from the automatic transaxle case sub-assembly.
35501
63.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
Move the manual valve lever shaft sub-assembly and parking lock rod sub-assembly as shown in the illustration, and remove the parking lock rod sub-assembly.
| *1 | Manual Valve Lever Shaft Sub-assembly | *2 | Parking Lock Rod Sub-assembly |
Align the cutouts of the parking lock rod sub-assembly and manual valve lever shaft sub-assembly and remove the parking lock rod sub-assembly.
35506
64.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY
Remove the manual valve lever shaft sub-assembly from the automatic transaxle case sub-assembly.
35557A
65.REMOVE PARKING LOCK PAWL TORSION SPRING
Remove the parking lock pawl torsion spring from the automatic transaxle case sub-assembly.
35556
66.REMOVE PARKING LOCK PAWL SHAFT
Remove the parking lock pawl shaft from the automatic transaxle case sub-assembly.
35557
67.REMOVE PARKING LOCK PAWL
Remove the parking lock pawl from the automatic transaxle case sub-assembly.
35598
68.REMOVE PARKING LOCK SLEEVE
Remove the parking lock sleeve from the automatic transaxle case sub-assembly.
69.INSPECT CLEARANCE OF B-1 BRAKE
70.REMOVE COUNTER DRIVE GEAR SUB-ASSEMBLY
|
"TORX" Bolt |
|
Bolt |
Using a T50 "TORX" socket wrench, remove the 2 "TORX" bolts from the counter drive gear sub-assembly.
Remove the 5 bolts from the counter drive gear sub-assembly.
Remove the counter drive gear sub-assembly together with the pinion and counter driven gear sub-assembly from the automatic transaxle case sub-assembly.
Remove the O-ring from the automatic transaxle case sub-assembly.
71.REMOVE NO. 1 BRAKE DISC
Using a screwdriver with its tip wrapped in protective tape, remove the snap ring from the counter drive gear sub-assembly.
Be careful not to damage the counter drive gear sub-assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
| *a | Snap Ring Side |
| *b | No. 1 Brake Disc Side |
Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the counter drive gear sub-assembly.
72.INSPECT NO. 1 BRAKE DISC
35739
73.REMOVE NO. 3 PLANETARY CARRIER THRUST WASHER
Remove the No. 3 planetary carrier thrust washer from the rear planetary gear assembly.
35760
74.REMOVE REAR PLANETARY GEAR ASSEMBLY
Remove the rear planetary gear assembly from the C-2 clutch assembly.
35729B
75.REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER
Remove the No. 4 planetary carrier thrust washer from the rear planetary gear assembly.
35760
76.INSPECT REAR PLANETARY GEAR ASSEMBLY
77.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-2 clutch assembly.
35787C
78.REMOVE NO. 2 THRUST BEARING RACE
Remove the No. 2 thrust bearing race from the C-2 clutch assembly.
79.INSPECT CLEARANCE OF C-2 CLUTCH
80.REMOVE C-2 CLUTCH ASSEMBLY
Remove the C-2 clutch assembly from the automatic transaxle case sub-assembly.
81.REMOVE THRUST NEEDLE ROLLER BEARING
Remove the thrust needle roller bearing from the C-2 clutch assembly.
35786A
82.REMOVE NO. 1 THRUST BEARING RACE
Remove the No. 1 thrust bearing race from the automatic transaxle case sub-assembly.
35667B
83.REMOVE NO. 2 CLUTCH DISC
Using a screwdriver with its tip wrapped in protective tape, remove the snap ring from the intermediate shaft sub-assembly.
Be careful not to damage the intermediate shaft sub-assembly.
| *1 | Direct Clutch Flange |
| *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate |
| *a | Snap Ring Side |
| *b | No. 2 Clutch Disc Side |
Remove the direct clutch flange, 4 No. 2 clutch discs and 4 No. 2 clutch plates from the intermediate shaft sub-assembly.
35667B
84.INSPECT NO. 2 CLUTCH DISC
35698A
85.REMOVE C-2 CLUTCH BALANCER
Place SST on the C-2 clutch balancer and compress the clutch return spring sub-assembly with a press.
Do not compress the clutch return spring sub-assembly excessively.
Using SST, remove the snap ring from the intermediate shaft sub-assembly.
Remove the C-2 clutch balancer from the intermediate shaft sub-assembly.
35608N
86.REMOVE CLUTCH RETURN SPRING SUB-ASSEMBLY
Remove the clutch return spring sub-assembly from the intermediate shaft sub-assembly.
35608N
87.INSPECT CLUTCH RETURN SPRING SUB-ASSEMBLY
35652E
88.REMOVE C-2 CLUTCH PISTON
|
Apply Compressed Air |
|
Cover Oil Hole |
Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole of the intermediate shaft sub-assembly.
Applying compressed air may cause the C-2 clutch piston to jump out. When removing the C-2 clutch piston, hold it by hand using a piece of cloth.
Be careful as ATF may spray when applying compressed air.
Cover all of the oil holes with tape except the oil hole to which compressed air will be applied.
Remove the C-2 clutch piston from the intermediate shaft sub-assembly.
Remove the 2 O-rings from the intermediate shaft sub-assembly.
35653B
89.REMOVE DIRECT CLUTCH DRUM OIL SEAL RING
Remove the 2 direct clutch drum oil seal rings from the automatic transaxle case sub-assembly.
90.INSPECT CLEARANCE OF B-2 BRAKE
35682
91.REMOVE 2ND BRAKE BRAKE DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
| *1 | 2nd Brake Brake Flange |
| *2 | 2nd Brake Brake Disc |
| *3 | 2nd Brake Brake Plate |
| *a | Snap Ring Side |
| *b | 2nd Brake Brake Disc Side |
Remove the 2nd brake brake flange, 5 2nd brake brake discs and 5 2nd brake brake plates from the automatic transaxle case sub-assembly.
35682
92.INSPECT 2ND BRAKE BRAKE DISC
35623P
93.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON
Remove the No. 2 1st and reverse brake piston from the automatic transaxle case sub-assembly.
35068
94.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.
Do not compress the 1st and reverse brake return spring sub-assembly excessively.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the automatic transaxle case sub-assembly.
35068
95.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
35623H
96.REMOVE 1ST AND REVERSE BRAKE PISTON
Apply compressed air (approximately 392 kPa (4.0 kgf/cm2, 57 psi)) to the ATF hole to remove the 1st and reverse brake piston from the automatic transaxle case sub-assembly.
Remove the 2 O-rings from the 1st and reverse brake piston.
97.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver with its tip wrapped with protective tape, remove the manual valve lever shaft oil seal from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
98.REMOVE TRANSAXLE CASE OIL SEAL
Using SST, remove the transaxle case oil seal from the transaxle housing.
Be careful not to damage the transaxle housing.
43410M
99.REMOVE FRONT DRIVE SHAFT OIL SEAL RH
Using SST, remove the front drive shaft oil seal RH from the transaxle housing.
Be careful not to damage the transaxle housing.
43420H
100.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
35605C
101.REMOVE NEEDLE ROLLER BEARING
Using SST and a press, remove the needle roller bearing from the transaxle housing.
Be careful not to damage the transaxle housing.
102.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the counter driven gear rear tapered roller bearing (outer race) from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.
Align the claw of SST with the indentation of the automatic transaxle case sub-assembly when removing the parts.
103.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)
Using SST, remove the counter driven gear rear tapered roller bearing (inner race) from the pinion and counter driven gear sub-assembly.
Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the counter driven gear rear tapered roller bearing (inner race) comes off.
If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts.
104.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the counter driven gear front tapered roller bearing (outer race) and pinion and counter driven gear shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
105.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)
Using SST, remove the counter driven gear front tapered roller bearing (inner race) from the pinion and counter driven gear sub-assembly.
106.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)
107.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)
108.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)
109.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
35104Q
110.REMOVE NO. 1 TRANSAXLE CASE PLUG
Remove the 4 No. 1 transaxle case plugs from the automatic transaxle case sub-assembly.
Remove the 4 No. 1 transaxle case plugs from the transaxle housing.
Remove the 8 O-rings from the 8 No. 1 transaxle case plugs.
35104R
111.REMOVE NO. 2 TRANSAXLE CASE PLUG
Using a 6 mm socket hexagon wrench, remove the 3 No. 2 transaxle case plugs and 3 gaskets from the automatic transaxle case sub-assembly.
Using a 6 mm socket hexagon wrench, remove the 3 No. 2 transaxle case plugs and 3 gaskets from the transaxle housing.
35101E
112.REMOVE AUTOMATIC TRANSMISSION CASE STRAIGHT PIN
It is not necessary to remove the automatic transmission case straight pins unless they are being replaced.
Remove the 2 automatic transmission case straight pins from the automatic transaxle case sub-assembly.
35104B
113.REMOVE NO. 1 BREATHER PLUG (ATM)
| *a | Push |
Disengage each claw and remove the No. 1 breather plug (ATM) from the automatic transaxle case sub-assembly.
Be careful not to damage the automatic transaxle case sub-assembly.