Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370692 TRANSMISSION WIRE A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  REMOVAL  


PROCEDURE

Hide 53896B 1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 6.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C402638

Remove the refill plug and gasket from the automatic transaxle case sub-assembly.


b.
C402774

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.


c.
C402778C01
2.75,0.917 2.854,0.917 false 2.552,0.833 2.719,1 0.167,0.167 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.


d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



f.

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 17650H 7.REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Hide 32901C 9.SEPARATE OIL COOLER UNION SUB-ASSEMBLY

a.
C402656C01
1.417,1.833 1.583,1.833 1.583,1.833 1.865,1.479 true 1.229,1.75 1.396,1.917 0.167,0.167 10 true *1
*1 Oil Cooler Union Bolt


Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.


b.

Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.


Hide 35151F 10.REMOVE TRANSMISSION CASE SIDE COVER

a.
C369210

Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.


Hide 82125J 11.REMOVE TRANSMISSION WIRE (w/o Stop And Start System)

a.
C376919

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C361008C01
0.135,0.208 0.448,0.365 0.313,0.156 10 false *a 0.615,3.229 0.927,3.385 0.313,0.156 10 false *b
*a Connector (A)
*b Connector (B)


Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


c.

Disconnect the 9 solenoid valve connectors.

HINT:
·

Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.

·

Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.




d.
C361010

Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.


e.
C374489

Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


f.
C361015

Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.


Hide 82125J 12.REMOVE TRANSMISSION WIRE (w/ Stop And Start System)

a.
C376919

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C365879C02
0.125,0.229 0.438,0.448 0.313,0.219 10 false *a 0.656,3.25 1.031,3.49 0.375,0.24 10 false *b
*a Connector (A)
*b Connector (B)


Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


c.

Disconnect the 9 solenoid valve connectors.

HINT:
·

Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.

·

Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.




d.
C365875

Disengage the wire harness clamp to disconnect the transmission wire (oil pump with solenoid assembly).


e.
C365876

Disconnect the transmission wire connector.


f.
C365877

Disengage the clamp to disconnect the transmission wire (oil pump with solenoid assembly) from the solenoid lock plate.


g.
C361010

Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.


h.
C374489

Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


i.
C361015

Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.