Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL (for LH Side)
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370705 DIFFERENTIAL OIL SEAL(for LH Side) A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for LH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C402796N01
1.083,2.333 1.333,2.333 1.333,2.333 1.333,1.729 false 0.75,2.25 1.167,2.417 0.417,0.167 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the automatic transaxle case sub-assembly.



Hide 43420H 3.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C402803C01
0.917,1.24 2.917,1.51 2.917,1.51 1.927,1.083 true 2.104,2.625 2.417,2.865 0.313,0.24 10 false *a 2.958,1.417 3.375,1.583 0.417,0.167 10 true SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.