Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER AND DRIVE PLATE
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370709 TORQUE CONVERTER AND DRIVE PLATE G

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.
C362562C01
0,0 0,0 false
V100135

Difficult
V100136

Smooth


Inspect the one-way clutch. Press on the splines of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch. Replace the torque converter assembly if the one-way clutch still fails the inspection.


b.
C197457C08
0.083,0 0.5,0.385 0.417,0.385 10 *a 1.677,3.26 1.865,3.417 0.188,0.156 10 *b
*a Sample showing maximum allowable amount of powder in ATF
*b Full Scale


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Malfunction:
·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or difficultly in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF in a Petri dish, which has been taken from the removed torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly and drain it before replacing the ATF.



d.
C295664C01
2.594,1.781 2.865,1.323 2.865,1.323 3.083,1.323 true 0.875,0.125 1.188,0.323 0.313,0.198 10 false *a 2.375,0.125 2.688,0.323 0.313,0.198 10 false *b 3.135,1.25 3.385,1.49 0.25,0.24 10 false *c
*a Correct
*b Incorrect
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 32101 2.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
C238929C03
1.675,0.338 1.803,0.493 0.129,0.155 10 1 1.253,1.045 1.382,1.2 0.129,0.155 10 2 1.818,1.958 1.947,2.114 0.129,0.155 10 3 2.674,1.932 2.803,2.087 0.129,0.155 10 4 2.881,1.213 3.009,1.368 0.129,0.155 10 5 2.443,0.525 2.571,0.68 0.129,0.155 10 6
V100144

Measurement Point


Check the drive plate and ring gear sub-assembly for damage.


b.

Set up a dial indicator and measure the runout at the 6 areas on the drive plate and ring gear sub-assembly surface that contact the torque converter assembly.

Maximum Runout:

0.30 mm (0.0118 in.)


HINT:
·

If the runout is more than the maximum or the drive plate and ring gear sub-assembly is damaged, replace the drive plate and ring gear sub-assembly.

·

If installing a new drive plate and ring gear sub-assembly, confirm that the spacers are oriented properly before tightening the bolts.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION