Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370710 OIL PUMP A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL RING PIN

a.
C362584

Install the 2 ring pins to the front oil pump cover sub-assembly.


Hide 35311 2.INSTALL FRONT OIL PUMP BODY

a.
C362583

Install the front oil pump body to the front oil pump cover sub-assembly.


Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C362582

Coat the front oil pump driven gear with Toyota Genuine ATF WS and install it to the front oil pump body.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

C362581

a.

Coat the front oil pump drive gear with Toyota Genuine ATF WS and install it to the front oil pump body.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C362580N01
1.74,0.823 1.896,1.021 0.156,0.198 10 true A 1.948,1.302 2.104,1.5 0.156,0.198 10 true A 2.042,0.75 2.198,0.948 0.156,0.198 10 true B 2.313,1.042 2.469,1.24 0.156,0.198 10 true B 1.531,1.135 1.688,1.333 0.156,0.198 10 true B

Install the stator shaft assembly to the front oil pump body with the 5 bolts.

Torque:
9.1 N*m (93 kgf*cm, 81 in.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
50 mm (1.97 in.) 45 mm (1.77 in.)



Hide 6.INSTALL OIL PUMP WITH SOLENOID ASSEMBLY (w/ Stop And Start System)

a.

Coat the O-ring of the oil pump with solenoid assembly with Toyota Genuine ATF WS.


b.
C388221

Install the oil pump with solenoid assembly to the front oil pump cover sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

The clamp is used as a jig during assembly at the factory. Discard the clamp after removing the oil pump with solenoid assembly.



Hide 7.INSTALL TRANSMISSION WIRE (OIL PUMP WITH SOLENOID ASSEMBLY) (w/ Stop And Start System)

a.
C388138

Connect the connector to install the transmission wire (oil pump with solenoid assembly).


Hide 35330F 8.INSTALL OIL STRAINER ASSEMBLY

a.
C403480C02
0.167,0.167 0.5,0.333 0.333,0.167 10 false *A 0.167,2.5 0.417,2.667 0.25,0.167 10 false *B
*A w/o Stop and Start System
*B w/ Stop and Start System


Using a T30 "TORX" socket wrench, install a new oil strainer assembly to the front oil pump cover sub-assembly with the 2 "TORX" bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35617 9.INSTALL CLUTCH DRUM OIL SEAL RING

a.

Apply a small amount of MP grease to the entire circumference of the clutch drum oil seal ring installation groove portion.

HINT:

By applying MP grease, the wobble within the clutch drum oil seal ring installation groove will be eliminated, preventing damage to the clutch drum oil seal ring at the time of front oil pump assembly installation.



b.
C403479C03
0.167,0.167 0.417,0.333 0.25,0.167 10 false *A 0.167,2.5 0.417,2.667 0.25,0.167 10 false *B
*A w/o Stop and Start System
*B w/ Stop and Start System


Coat 4 new clutch drum oil seal rings with Toyota Genuine ATF WS and install them to the stator shaft assembly.

NOTICE:

While making the spread of the opening of the clutch drum oil seal ring as small as possible, install it to the stator shaft assembly.

If the ring opening is spread, briefly hold it closed with your fingers to return it to its original condition.