Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Electric Parking Brake ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Electric Parking Brake ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Electric Parking Brake" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Electric Parking Brake" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Electric Parking Brake" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Electric Parking Brake ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Parking brake ECU assembly branch wire or connector

·

Power source circuit of parking brake ECU assembly

·

Parking brake ECU assembly ground circuit

·

Parking brake ECU assembly



WIRING DIAGRAM

C405902E01
5.156,5.042 7.052,5.406 1.896,0.365 10 false Parking Brake ECU Assembly 5.677,0.417 6.292,0.615 0.615,0.198 10 false CANH 5.688,0.938 6.302,1.135 0.615,0.198 10 false CANL 5.688,2.26 6.302,2.458 0.615,0.198 10 false IG 5.646,4.49 6.26,4.688 0.615,0.198 10 false GND1 5.656,3.948 6.271,4.146 0.615,0.198 10 false BECU 5.667,3.396 6.281,3.594 0.615,0.198 10 false +B2 5.25,0.427 5.865,0.625 0.615,0.198 10 false M35 5.26,0.938 5.875,1.135 0.615,0.198 10 false M35 5.25,2.813 5.865,3.01 0.615,0.198 10 false M36 5.25,3.365 5.865,3.563 0.615,0.198 10 false M36 5.25,3.927 5.865,4.125 0.615,0.198 10 false M35 5.26,4.49 5.875,4.688 0.615,0.198 10 false M36 5.313,0.198 5.531,0.385 0.219,0.188 10 false 11 5.344,4.281 5.5,4.479 0.156,0.198 10 false 9 5.344,3.729 5.5,3.927 0.156,0.198 10 false 3 5.302,3.177 5.521,3.365 0.219,0.188 10 false 12 5.344,2.604 5.5,2.802 0.156,0.198 10 false 7 5.344,0.719 5.5,0.917 0.156,0.198 10 false 1 1.521,0.302 1.677,0.5 0.156,0.198 10 false 5 1.51,0.833 1.76,1.042 0.25,0.208 10 false 11 0.208,1.427 2.542,1.781 2.333,0.354 10 false No. 6 CAN Junction Connector 0.208,1.26 0.823,1.458 0.615,0.198 10 false M31 3.865,2.052 5,2.396 1.135,0.344 10 false ECU-IG1 NO.3 4.021,3.229 4.958,3.563 0.938,0.333 10 false EPB NO.2 3.938,3.792 4.969,4.125 1.031,0.333 10 false ECU-B NO.2 1.677,3.927 3.146,4.333 1.469,0.406 10 false from Auxiliary Battery 1.74,2.25 3.396,2.688 1.656,0.438 10 false from IG1 NO.1 Relay 1.698,3.354 3.167,3.76 1.469,0.406 10 false from Auxiliary Battery 5.25,2.25 5.865,2.448 0.615,0.198 10 false M35 5.333,2.031 5.49,2.229 0.156,0.198 10 false 5 1.688,2.802 3.156,3.208 1.469,0.406 10 false from Auxiliary Battery 5.677,2.792 6.292,2.99 0.615,0.198 10 false +B 4,2.635 4.938,2.969 0.938,0.333 10 false EPB NO.1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (PARKING BRAKE ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C300835C21
0.24,1.042 0.667,1.323 0.427,0.281 1.115,1.104 1.552,0.479 1.552,0.479 1.688,0.479 true 1.115,1.406 1.396,1.771 1.396,1.771 1.531,1.771 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 1.76,0.417 2.188,0.583 0.427,0.167 10 false CANL 0.344,1.115 0.708,1.281 0.365,0.167 10 false M35 1.573,1.719 2,1.885 0.427,0.167 10 false CANH
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-11 (CANH) - M35-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C306911C27
1.51,0.406 1.938,0.667 0.427,0.26 1.49,2.458 1.917,2.719 0.427,0.26 0.802,2.01 0.969,2.01 0.969,2.01 1.646,1.406 true 2.615,4.292 2.469,4.292 2.469,4.292 2.313,3.646 true 2.052,4.51 1.896,4.51 1.896,4.51 1.656,3.656 true 0.75,4.271 0.917,4.271 0.917,4.271 1.135,3.646 true 1.083,0.604 1.25,0.604 1.25,0.604 1.365,1.365 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.615,0.479 2.073,0.677 0.458,0.198 10 false M35 0.615,1.948 0.927,2.146 0.313,0.198 10 false IG 0.552,4.198 0.865,4.396 0.313,0.198 10 false +B 2.667,4.219 3.042,4.417 0.375,0.198 10 false +B2 2.125,4.458 2.667,4.625 0.542,0.167 10 false GND1 1.573,2.531 2.031,2.729 0.458,0.198 10 false M36 0.656,0.542 1.281,0.698 0.625,0.156 10 false BECU
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M36-9 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M36-7 (+B) - Body ground Power switch off 11 to 14 V
M36-12 (+B2) - Body ground Power switch off 11 to 14 V
M35-3 (BECU) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
M35-5 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR