Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Driver Seat Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driver Seat Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "D-Seat" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "D-Seat" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "D-Seat" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Driver Seat Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Position control ECU assembly branch wire or connector

·

Power source circuit of position control ECU assembly

·

Position control ECU assembly ground circuit

·

Position control ECU assembly



WIRING DIAGRAM

for LHD:
C368276E21
5.583,0.677 6.198,0.875 0.615,0.198 10 false CANP 5.594,1.271 6.208,1.469 0.615,0.198 10 false CANN 5.594,3.344 6.208,3.542 0.615,0.198 10 false GND 5.604,1.802 6.219,2 0.615,0.198 10 false IG 5.604,2.323 6.219,2.521 0.615,0.198 10 false +B 5.594,2.813 6.208,3.01 0.615,0.198 10 false SYSB 5.25,0.667 5.865,0.865 0.615,0.198 10 false T8 5.25,1.26 5.865,1.458 0.615,0.198 10 false T8 5.25,0.49 5.865,0.688 0.615,0.198 10 false 13 5.25,1.063 5.865,1.26 0.615,0.198 10 false 14 1.646,1.177 2.26,1.375 0.615,0.198 10 false 10 1.656,0.604 2.271,0.802 0.615,0.198 10 false 4 0.271,1.469 0.885,1.667 0.615,0.198 10 false N52 0.26,1.656 1.635,2.042 1.375,0.385 10 false No. 7 CAN Junction Connector 5.469,3.948 6.865,4.583 1.396,0.635 10 false Position Control ECU Assembly 5.292,1.604 5.906,1.802 0.615,0.198 10 false 1 5.24,1.792 5.854,1.99 0.615,0.198 10 false T8 5.25,2.802 5.865,3 0.615,0.198 10 false T8 5.25,2.625 5.865,2.823 0.615,0.198 10 false 15 5.292,2.125 5.906,2.323 0.615,0.198 10 false 3 5.25,2.302 5.865,2.5 0.615,0.198 10 false T7 5.26,3.344 5.875,3.542 0.615,0.198 10 false T7 5.292,3.167 5.906,3.365 0.615,0.198 10 false 2 4.021,1.646 5.073,1.885 1.052,0.24 10 false ECU-IG1 NO.4 4.094,2.167 5.146,2.406 1.052,0.24 10 false P/SEAT F/L 3.948,2.677 5,2.917 1.052,0.24 10 false ECU-DCC NO.2 2.552,2.292 3.99,2.531 1.438,0.24 10 false from Battery 2.042,1.781 3.583,2.073 1.542,0.292 10 false from IG1 NO.1 Relay 2.573,2.771 4.01,3.01 1.438,0.24 10 false from Battery

for RHD:
C368276E22
5.583,0.677 6.198,0.875 0.615,0.198 10 false CANP 5.594,1.271 6.208,1.469 0.615,0.198 10 false CANN 5.594,3.344 6.208,3.542 0.615,0.198 10 false GND 5.604,1.802 6.219,2 0.615,0.198 10 false IG 5.604,2.323 6.219,2.521 0.615,0.198 10 false +B 5.594,2.813 6.208,3.01 0.615,0.198 10 false SYSB 5.25,0.667 5.865,0.865 0.615,0.198 10 false S8 5.25,1.26 5.865,1.458 0.615,0.198 10 false S8 5.25,0.49 5.865,0.688 0.615,0.198 10 false 13 5.25,1.063 5.865,1.26 0.615,0.198 10 false 14 1.646,1.188 2.26,1.385 0.615,0.198 10 false 19 1.656,0.604 2.271,0.802 0.615,0.198 10 false 8 0.167,1.469 0.781,1.667 0.615,0.198 10 false G105 0.177,1.656 1.458,2.167 1.281,0.51 10 false No. 5 CAN Junction Connector 5.469,3.948 6.865,4.583 1.396,0.635 10 false Position Control ECU Assembly 5.292,1.604 5.906,1.802 0.615,0.198 10 false 1 5.24,1.792 5.854,1.99 0.615,0.198 10 false S8 5.25,2.802 5.865,3 0.615,0.198 10 false S8 5.25,2.625 5.865,2.823 0.615,0.198 10 false 15 5.292,2.125 5.906,2.323 0.615,0.198 10 false 3 5.25,2.302 5.865,2.5 0.615,0.198 10 false S7 5.26,3.344 5.875,3.542 0.615,0.198 10 false S7 5.292,3.167 5.906,3.365 0.615,0.198 10 false 2 4.042,1.646 5.094,1.885 1.052,0.24 10 false ECU-IG1 NO.4 4.094,2.177 5.146,2.417 1.052,0.24 10 false P/SEAT F/R 3.948,2.667 5,2.906 1.052,0.24 10 false ECU-DCC NO.2 2.542,2.292 3.979,2.531 1.438,0.24 10 false from Battery 2.01,1.781 3.552,2.073 1.542,0.292 10 false from IG1 NO.1 Relay 2.531,2.771 3.969,3.01 1.438,0.24 10 false from Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POSITION CONTROL ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369138C32
1.5,0.052 1.917,0.302 0.417,0.25 1.5,0.375 1.917,0.625 0.417,0.25 2.083,0.917 2.25,0.917 2.25,0.917 2.646,1.719 true 2.167,0.75 2.333,0.75 2.333,0.75 2.823,1.708 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.635,0.104 1.948,0.302 0.313,0.198 10 false T8 1.646,0.854 2.104,1.052 0.458,0.198 10 false CANP 1.76,0.677 2.219,0.875 0.458,0.198 10 false CANN 1.635,0.417 1.948,0.615 0.313,0.198 10 false S8 1.979,0.094 2.292,0.292 0.313,0.198 10 false *A 1.979,0.417 2.292,0.615 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU Assembly)


Disconnect the position control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-13 (CANP) - T8-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition
S8-13 (CANP) - S8-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C371309C09
1.083,0.115 1.49,0.344 0.406,0.229 0.26,2.74 0.667,2.969 0.406,0.229 1.969,0.115 2.375,0.344 0.406,0.229 0.26,2.25 0.667,2.479 0.406,0.229 1.094,2.021 1.26,2.021 1.26,2.021 1.427,2.354 true 2.333,2 2.167,2 2.167,2 2,2.333 true 0.688,0.156 0.854,0.156 0.854,0.156 0.854,0.906 true 0.469,1.552 0.635,1.552 0.635,1.552 0.844,1.188 true 1.219,0.146 1.531,0.344 0.313,0.198 10 false T8 0.396,2.292 0.708,2.49 0.313,0.198 10 false T7 0.75,1.938 1.146,2.115 0.396,0.177 10 false GND 2.375,1.917 2.771,2.094 0.396,0.177 10 false +B 0.063,0.063 0.458,0.24 0.396,0.177 10 false *a 0.521,0.083 1,0.281 0.479,0.198 10 false IG 0.104,1.49 0.5,1.667 0.396,0.177 10 false SYSB 2.094,0.146 2.406,0.344 0.313,0.198 10 false S8 1.542,0.146 1.854,0.344 0.313,0.198 10 false *A 2.438,0.146 2.75,0.344 0.313,0.198 10 false *B 0.385,2.781 0.698,2.979 0.313,0.198 10 false S7 0.74,2.292 1.052,2.49 0.313,0.198 10 false *A 0.74,2.781 1.052,2.979 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU Assembly)


Disconnect the position control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
S7-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
T7-3 (+B) - Body ground Always 11 to 14 V
T8-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
T8-15 (SYSB) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
S7-3 (+B) - Body ground Always 11 to 14 V
S8-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
S8-15 (SYSB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR