Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Four Wheel Drive Control" is indicated on "CAN Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Four Wheel Drive Control" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Four Wheel Drive Control" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

4WD ECU assembly CAN branch wire or connector

·

Power source circuit of 4WD ECU assembly

·

4WD ECU assembly ground circuit

·

4WD ECU assembly



WIRING DIAGRAM

C405872E04
5.292,4.021 6.917,4.281 1.625,0.26 10 false 4WD ECU Assembly 5.583,3.188 6.021,3.427 0.438,0.24 10 false GND 5.583,2.271 5.948,2.521 0.365,0.25 10 false IG1 5.573,1.271 7,1.583 1.427,0.313 10 false CANL 5.583,0.677 7.01,0.99 1.427,0.313 10 false CANH 4.802,0.667 5.146,0.938 0.344,0.271 10 false N4 4.75,0.448 5.146,0.667 0.396,0.219 10 false 17*1 3.104,2.125 4.5,2.354 1.396,0.229 10 false ECU-IG1 NO.2 1.198,2.271 2.771,2.583 1.573,0.313 10 false from IG1 NO.1 Relay 1.656,1.135 1.875,1.375 0.219,0.24 10 false 9 1.646,0.552 1.906,0.781 0.26,0.229 10 false 3 0.156,1.563 1.583,1.875 1.427,0.313 10 false G104 0.167,1.74 2.542,1.948 2.375,0.208 10 false No. 4 CAN Junction Connector 4.802,1.25 5.146,1.521 0.344,0.271 10 false N4 4.823,2.271 5.167,2.542 0.344,0.271 10 false N3 4.813,3.156 5.156,3.427 0.344,0.271 10 false N3 5.229,0.667 5.573,0.938 0.344,0.271 10 false N5 5.229,1.26 5.573,1.531 0.344,0.271 10 false N5 5.24,2.271 5.583,2.542 0.344,0.271 10 false N5 5.229,3.146 5.573,3.417 0.344,0.271 10 false N5 4.74,1.042 5.135,1.26 0.396,0.219 10 false 26*1 5.208,0.458 5.604,0.677 0.396,0.219 10 false 6*2 5.208,1.052 5.604,1.271 0.396,0.219 10 false 5*2 4.75,2.073 5.146,2.292 0.396,0.219 10 false 24*1 4.792,2.958 5.188,3.177 0.396,0.219 10 false 1*1 5.208,2.073 5.604,2.292 0.396,0.219 10 false 3*2 5.219,2.958 5.615,3.177 0.396,0.219 10 false 4*2 0.365,3.719 3.708,3.979 3.344,0.26 10 false *1: for Dynamic Torque Control 4WD/AWD System 0.375,4.073 3.771,4.333 3.396,0.26 10 false *2: for Dynamic Torque Vectoring AWD System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for Dynamic Torque Control 4WD/AWD System A
for Dynamic Torque Vectoring AWD System B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY BRANCH WIRE)

B

4.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY BRANCH WIRE)
a.
C369140C76
1.5,0.5 1.917,0.75 0.417,0.25 2.75,0.667 2.583,0.667 2.583,0.667 2.583,1.917 true 2.75,2.833 2.583,2.833 2.583,2.833 2.583,2.25 true 1.646,0.542 1.958,0.74 0.313,0.198 10 false N4 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.813,0.583 3.292,0.813 0.479,0.229 10 false CANH 2.813,2.771 3.292,3 0.479,0.229 10 false CANL
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
N4-17 (CANH) - N4-26 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 4WD ECU assembly connector.


b.
C408010C04
1.552,0.073 1.906,0.323 0.354,0.25 2.521,1.531 2.833,0.833 2.833,0.833 3,0.833 true 1.063,0.833 0.688,0.719 0.688,0.719 0.521,0.719 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 3.042,0.771 3.375,1.052 0.333,0.281 10 false IG1 1.625,0.125 2.083,0.323 0.458,0.198 10 false N3 0.177,0.646 0.594,0.896 0.417,0.25 10 false GND
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-1 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N3-24 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY BRANCH WIRE)
a.
C369144C48
1.5,0.167 1.917,0.417 0.417,0.25 1.083,2.667 0.917,2.667 0.917,2.667 0.75,2.083 true 0.969,2.885 0.802,2.885 0.802,2.885 0.573,2.073 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.208 1.938,0.406 0.313,0.198 10 false N5 1.135,2.594 1.615,2.802 0.479,0.208 10 false CANH 1.052,2.833 1.531,3.042 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
N5-6 (CANH) - N5-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (4WD ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369144C49
1.5,0.167 1.917,0.417 0.417,0.25 2.469,1.74 2.25,0.958 2.25,0.958 2.083,0.958 true 2.792,1.74 2.438,0.708 2.438,0.708 2.271,0.708 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.208 1.938,0.406 0.313,0.198 10 false N5 1.813,0.896 2.292,1.104 0.479,0.208 10 false IG1 1.927,0.625 2.406,0.833 0.479,0.208 10 false GND
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N5-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N5-3 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)