Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Stop and Go/Start" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Stop and Go/Start" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Engine stop and start ECU branch wire or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C410333E03
0.073,1.229 0.969,1.542 0.896,0.313 10 false G103 0.083,1.396 2.115,1.865 2.031,0.469 10 false No. 3 CAN Junction Connector 1.573,0.375 2.792,0.573 1.219,0.198 10 false 6 1.542,0.906 2.646,1.115 1.104,0.208 10 false 16 4.854,0.479 5.313,0.677 0.458,0.198 10 false A32 4.854,1.01 5.313,1.208 0.458,0.198 10 false A32 5.271,1.573 5.729,1.771 0.458,0.198 10 false A33 5.281,2.125 5.74,2.323 0.458,0.198 10 false A33 5.281,2.677 5.74,2.875 0.458,0.198 10 false A34 5.26,3.229 5.719,3.427 0.458,0.198 10 false G62 5.26,3.792 5.719,3.99 0.458,0.198 10 false G62 5.271,4.344 5.729,4.542 0.458,0.198 10 false G62 5.292,4.906 5.75,5.104 0.458,0.198 10 false A33 5.281,5.458 5.74,5.656 0.458,0.198 10 false A33 5.688,5.479 6.146,5.677 0.458,0.198 10 false GND2 5.677,4.896 6.135,5.094 0.458,0.198 10 false GND1 5.677,4.375 6.135,4.573 0.458,0.198 10 false ACC 5.677,3.813 6.135,4.01 0.458,0.198 10 false IG2 5.656,3.271 6.115,3.469 0.458,0.198 10 false IG1 5.688,2.698 6.146,2.896 0.458,0.198 10 false +B 5.667,2.146 6.125,2.344 0.458,0.198 10 false BIN2 5.667,1.604 6.125,1.802 0.458,0.198 10 false BIN1 5.667,1.042 6.125,1.24 0.458,0.198 10 false CANL 5.656,0.479 6.115,0.677 0.458,0.198 10 false CANH 4.844,0.281 5.302,0.479 0.458,0.198 10 false 13*1 4.844,0.802 5.302,1 0.458,0.198 10 false 14*1 5.344,1.385 5.802,1.583 0.458,0.198 10 false 3 5.354,1.927 5.813,2.125 0.458,0.198 10 false 1 5.354,2.458 5.813,2.656 0.458,0.198 10 false 1 5.271,3.01 5.729,3.208 0.458,0.198 10 false 21*2 5.26,3.573 5.719,3.771 0.458,0.198 10 false 18*2 5.26,4.135 5.719,4.333 0.458,0.198 10 false 19*2 5.354,4.688 5.813,4.885 0.458,0.198 10 false 8 5.167,5.917 6.99,6.5 1.823,0.583 10 false Engine Stop and Start ECU 5.365,5.25 5.823,5.448 0.458,0.198 10 false 2 4.042,1.438 4.823,1.646 0.781,0.208 10 false BBC NO.1 4.031,1.958 4.813,2.167 0.781,0.208 10 false BBC NO.2 4.083,2.531 4.865,2.74 0.781,0.208 10 false EFI NO.1 4.115,3.094 4.896,3.302 0.781,0.208 10 false EPS-IG1 3.99,3.635 4.948,3.875 0.958,0.24 10 false METER-IG2 4.042,4.208 5.01,4.427 0.969,0.219 10 false ECU ACC 2.052,4.365 3.219,4.615 1.167,0.25 10 false from ACC Relay 1.792,3.781 3.302,4.156 1.51,0.375 10 false from IG2 NO.2 Relay 1.792,3.229 3.26,3.521 1.469,0.292 10 false from IG1 NO.1 Relay 1.396,2.677 3.167,3.063 1.771,0.385 10 false from EFI-MAIN NO.1 Relay 2.292,2.156 3.479,2.458 1.188,0.302 10 false from Battery 2.292,1.573 3.5,1.813 1.208,0.24 10 false from Battery 5.26,1.01 5.719,1.208 0.458,0.198 10 false G62 5.26,0.49 5.719,0.688 0.458,0.198 10 false G62 5.24,0.281 5.698,0.479 0.458,0.198 10 false 13*2 5.24,0.802 5.698,1 0.458,0.198 10 false 14*2 0.292,6.375 1.458,6.625 1.167,0.25 10 false *2: for RHD 0.292,6.052 1.458,6.302 1.167,0.25 10 false *1: for LHD 4.833,3 5.292,3.198 0.458,0.198 10 false 21*1 4.854,3.219 5.313,3.417 0.458,0.198 10 false A32 4.833,3.573 5.292,3.771 0.458,0.198 10 false 18*1 4.854,3.792 5.313,3.99 0.458,0.198 10 false A32 4.833,4.135 5.292,4.333 0.458,0.198 10 false 19*1 4.854,4.354 5.313,4.552 0.458,0.198 10 false A32

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C300830C19
0.958,0.177 1.375,0.427 0.417,0.25 2.094,0.188 2.51,0.438 0.417,0.25 0.729,1.823 0.844,1.823 0.844,1.823 0.781,1.406 true 1.365,1.813 1.188,1.813 1.188,1.813 0.938,1.406 true 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 1.052,0.219 1.406,0.375 0.354,0.156 10 false A32 0.354,1.76 0.76,1.906 0.406,0.146 10 false CANH 1.438,1.76 1.844,1.906 0.406,0.146 10 false CANL 1.438,0.229 1.792,0.385 0.354,0.156 10 false *A 2.198,0.229 2.552,0.385 0.354,0.156 10 false G62 2.583,0.24 2.938,0.396 0.354,0.156 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A32-13 (CANH) - A32-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition
G62-13 (CANH) - G62-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the engine stop and start ECU connectors.

C382798C03
1,0.188 1.417,0.427 0.417,0.24 3.323,0.156 3.74,0.396 0.417,0.24 5.313,0.115 5.729,0.354 0.417,0.24 6.188,0.115 6.604,0.354 0.417,0.24 0.344,0.885 0.438,1.417 0.438,1.417 0.604,1.417 true 3.115,0.729 2.969,0.385 2.969,0.385 2.813,0.385 true 3.104,1 2.854,0.802 2.854,0.802 2.698,0.802 true 3.99,0.771 4.135,0.396 4.135,0.396 4.302,0.396 true 3.969,1.135 4.01,1.458 4.01,1.458 4.177,1.458 true 5.708,1.104 5.323,1.469 5.323,1.469 5.167,1.469 true 5.813,1.135 5.677,1.646 5.677,1.646 5.521,1.646 true 6.24,1.115 6.146,1.583 6.146,1.583 6.313,1.583 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.094,0.229 1.406,0.427 0.313,0.198 10 false A34 3.427,0.198 3.74,0.396 0.313,0.198 10 false A33 5.385,0.146 5.698,0.344 0.313,0.198 10 false A32 2.458,0.313 2.865,0.531 0.406,0.219 10 false BIN2 0.656,1.365 0.969,1.563 0.313,0.198 10 false +B 2.354,0.729 2.76,0.99 0.406,0.26 10 false BIN1 4.354,0.333 4.865,0.573 0.51,0.24 10 false GND2 4.229,1.406 4.75,1.625 0.521,0.219 10 false GND1 4.896,1.396 5.281,1.594 0.385,0.198 10 false IG2 5.198,1.573 5.583,1.771 0.385,0.198 10 false ACC 6.354,1.521 6.74,1.719 0.385,0.198 10 false IG1 5.76,0.146 6.073,0.344 0.313,0.198 10 false *A 6.646,0.146 6.958,0.344 0.313,0.198 10 false *B 6.271,0.156 6.583,0.354 0.313,0.198 10 false G62
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A33-8 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Always 9.5 to 14 V
A33-1 (BIN2) - Body ground Always 9.5 to 14 V
A33-3 (BIN1) - Body ground Always 9.5 to 14 V
A32-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
A32-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
A32-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V
Ignition switch off Below 1 V

for RHD
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Always 9.5 to 14 V
A33-1 (BIN2) - Body ground Always 9.5 to 14 V
A33-3 (BIN1) - Body ground Always 9.5 to 14 V
G62-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
G62-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
G62-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)