The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | Note |
|---|---|---|---|---|---|---|
| P161A87 | Lost Communication with Alternator Missing Message | Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic) |
·
Wire harness or connector ·
Generator assembly ·
ECM |
Charge warning light does not come on | DTC stored | SAE Code: P161A |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before replacing the ECM, refer to Service Bulletin.
Check the charging system.
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Stop and Start System) | A |
| OK (w/o Stop and Start System) | B |
| NG | C |
A
B
C
Disconnect the C40 ECM connector.
Disconnect the C46 generator assembly connector.
Disconnect the A48 battery state sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-2 (LIN) or C46-2 (LIN) - C40-62 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-2(LIN), C46-2 (LIN) or C40-62 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check for DTCs, and then write them down.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Clear the DTCs.
Turn the ignition switch off and wait 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine.
Allow the engine to idle for approximately 17 minutes or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only DTC P161A87 is output. | A |
| DTC P161A87 and P162B87 are output. | B |
| DTCs are not output. | C |
A
for 100 A, 130 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 100 A, 130 A Type)>REMOVAL
for 150 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 150 A Type)>REMOVAL
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the C40 ECM connector.
Disconnect the C46 generator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-2 (LIN) - C40-62 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-2 (LIN) or C40-62 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the generator assembly.
for 100 A, 130 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 100 A, 130 A Type)>INSPECTION
for 150 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 150 A Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 100 A, 130 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 100 A, 130 A Type)>REMOVAL
for 150 A Type
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 150 A Type)>REMOVAL