Home › Drivetrain › EG62 (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM3620E _52 Drivetrain _076270 EG62 MANUAL TRANSMISSION / TRANSAXLE _0371327 DIFFERENTIAL CASE G

EG62 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41302F 1.INSPECT FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C400513N01
0.875,1.115 1.698,1.281 true 0.563,1.021 1.167,1.365 0.604,0.344 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05030)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all remaining inspection procedures.

·

Replace any parts that do not meet the specifications.

·

If the front differential side gear locks after performing the inspection procedures, replace the front differential case sub-assembly.



Hide 2.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

a.

Mount the front differential case sub-assembly in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential case sub-assembly.

·

Do not overtighten the vise.




b.
C400514C01
0.448,1.885 1.385,2.083 true 2.75,4.25 3.063,4.406 0.313,0.156 10 false *a 0.125,1.781 0.583,1.979 0.458,0.198 10 false SST
*a Front Differential Side Gear Thrust Amount


Using SST and a dial indicator, measure the front differential side gear thrust amount.

SST
09528-52010  (09528-05030)

Front Differential Side Gear Thrust Amount:

0.08 mm (0.00315 in.) or less


HINT:
·

Measure the front differential side gear thrust amount while slowly rotating the front differential side gear.

·

Make sure to measure the front differential side gear thrust amount for both of the front differential side gears.



If the result is not as specified, replace the 2 conical spring washers, 2 front differential side gears and 2 front differential pinions.


Hide 3.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Set SST as shown in the illustration and tighten it.

C400515C01
0.688,0.677 1.375,0.99 true 3.198,0.927 3.51,1.083 0.313,0.156 10 false *a 0.771,2.427 1.083,2.583 0.313,0.156 10 false *b 0.396,0.583 0.854,0.781 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Mount the front differential case sub-assembly in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential case sub-assembly.

·

Do not overtighten the vise.




c.
C400516C01
1.396,0.448 2.625,0.448 true 1.24,0.354 1.552,0.51 0.313,0.156 10 false *1
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


d.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.20 mm (0.00787 in.) or less


If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

Front No. 1 Differential Side Gear Thrust Washer Thickness:
Part No. Thickness mm (in.) Mark
41361-28230 1.00 (0.0394) 1
41361-28240 1.10 (0.0433) 2
41361-28250 1.20 (0.0472) 3
41361-28260 1.30 (0.0512) 4


HINT:

Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.



Hide 41351F 4.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.9 mm (0.0354 in.)


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 5.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C291384C01
2.542,0.823 2.854,1.021 0.313,0.198 10 false *a
*a Outer Diameter


Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

17.975 mm (0.708 in.)


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.