Home › Drivetrain › EG62F (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM3620E _52 Drivetrain _076271 EG62F MANUAL TRANSMISSION / TRANSAXLE _0371332 DIFFERENTIAL CASE A

EG62F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 43410M 1.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.

·

Do not overtighten the vise.




b.
C402337N01
2.396,2.375 2.146,2.375 2.146,2.375 1.885,2.031 false 2.427,2.292 2.792,2.531 0.365,0.24 10 false SST

Using SST, remove the front drive shaft oil seal RH from the front differential case.

SST
09308-00010  


Hide 41221 2.REMOVE FRONT DIFFERENTIAL RING GEAR

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.

·

Do not overtighten the vise.




b.
C400505C01
1.875,0.469 2.771,0.281 2.771,0.281 1.875,0.396 true 2.802,0.177 3.115,0.333 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front differential case sub-assembly.


c.
C400506

Remove the 12 bolts.


d.
C402340

Using a plastic-faced hammer, remove the front differential ring gear from the front differential case sub-assembly.


Hide 41302F 3.INSPECT FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 4.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

Hide 41342A 5.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.

Mount the front differential case sub-assembly in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential case sub-assembly.

·

Do not overtighten the vise.




b.
C402341N01
1.979,2.24 2.396,1.792 2.396,1.792 2.594,1.792 true 2.635,1.708 3.01,1.938 0.375,0.229 10 false SST

Using SST and a hammer, remove the front differential pinion shaft straight pin from the front differential case sub-assembly.

SST
09201-10000  (09201-01050)


Hide 41342F 6.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C402342

Remove the front No. 1 differential pinion shaft from the front differential case sub-assembly.


Hide 7.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41331F 8.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Set SST as shown in the illustration and tighten it.

C402326C01
0.656,0.375 0.948,0.375 0.948,0.375 1.729,0.708 true 0.333,0.313 0.646,0.531 0.313,0.219 10 false SST 3.635,0.104 3.896,0.323 0.26,0.219 10 false *a 1.115,2.146 1.354,2.354 0.24,0.208 10 false *b
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring washer, front No. 1 differential side gear thrust washer and front differential case.


HINT:
·

Tighten SST until there is clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C402327C01
2.333,2.75 2.333,2.323 2.333,2.323 2.573,1.844 true 2.188,2.771 2.573,3.01 0.385,0.24 10 false SST 1.583,1.188 1.844,1.417 0.26,0.229 10 false *a
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



c.
C402328C01
2.042,1.333 2.313,1.333 false 2.125,0.906 2.396,0.906 false 2.042,1.917 2.313,1.917 false 2.125,2.344 2.396,2.344 false 2.198,2.76 2.448,2.76 2.448,2.76 2.5,2.646 false 2.104,0.5 2.406,0.5 2.406,0.5 2.49,0.615 false 1.854,1.26 2.073,1.458 0.219,0.198 10 false *1 1.938,0.833 2.167,1.063 0.229,0.229 10 false *2 1.917,0.438 2.135,0.646 0.219,0.208 10 false *3 2,2.688 2.208,2.906 0.208,0.219 10 false *3 1.927,2.271 2.146,2.479 0.219,0.208 10 false *2 1.854,1.854 2.052,2.083 0.198,0.229 10 false *1
*1 Front Differential Side Gear
*2 Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case sub-assembly, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical spring washers from the front differential case.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring washer.