Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371514 CYLINDER HEAD A

A25A-FKS ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A400462N01
1.354,1.042 0.677,1.375 0.677,1.375 1.406,0.833 true 0.458,1.417 0.917,1.615 0.458,0.198 10 true SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A400463

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40877 to 0.40921 in.)


Standard Bush Length:

41.3 to 41.7 mm (1.63 to 1.64 in.)


HINT:
·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.

·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A400464C01
1.354,1.042 0.729,1.344 0.729,1.344 1.458,0.646 true 2.469,1.948 2.677,2.156 0.208,0.208 10 true *a 0.552,1.406 1.01,1.604 0.458,0.198 10 true SST
*a Protrusion Height


Using SST and a hammer, tap in the selected intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

17.75 to 17.95 mm (0.699 to 0.707 in.)



h.
A400465

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A400466N01
1.094,1.135 1.354,0.885 1.354,0.885 0.979,0.896 true 1.427,0.792 1.885,0.99 0.458,0.198 10 true SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A400467

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40877 to 0.40921 in.)


Standard Bush Length:

43.3 to 43.7 mm (1.70 to 1.72 in.)


HINT:
·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.

·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A400468C01
0.927,0.813 1.458,0.833 1.458,0.833 1.094,1.135 true 3.104,1.5 3.354,1.698 0.25,0.198 10 true *a 1.594,0.729 2.01,0.906 0.417,0.177 10 true SST
*a Protrusion Height


Using SST and a hammer, tap in the selected exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

17.75 to 17.95 mm (0.699 to 0.707 in.)



h.
A400469

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11155A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 2 ring pins.


b.
A400470C01
2.219,2.354 2.531,2.552 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, tap in 2 new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)