Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371643 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84010D 1.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY

a.

Inspect EV mode switch (Integration Control and Panel Assembly)

i.
C331272C13
1.458,0.188 1.875,0.448 0.417,0.26 2.563,1.302 2.563,1.688 true 2.292,0.448 1.813,0.969 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 2.365,0.323 2.521,0.521 0.156,0.198 10 false S 2.417,1.719 2.865,1.927 0.448,0.208 10 false GND 1.531,0.24 1.99,0.438 0.458,0.198 10 false G32
*a Component without harness connected
(EV Mode Switch (Integration Control and Panel Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-6 (S) - G32-13 (GND) EV mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
EV mode switch (integration control and panel assembly) not pushed 10 kΩ or higher


If the result is not as specified, replace the EV mode switch (integration control and panel assembly).



b.

Inspect NORMAL mode switch (Integration Control and Panel Assembly)

i.
C331272C15
1.479,0.219 1.875,0.469 0.396,0.25 2.552,1.281 2.552,1.677 true 0.99,0.375 1.448,0.969 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.813,0.25 0.969,0.396 0.156,0.146 10 false B 2.417,1.719 2.979,1.917 0.563,0.198 10 false GND 1.542,0.271 2,0.469 0.458,0.198 10 false G32
*a Component without harness connected
(NORMAL Mode Switch (Integration Control and Panel Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-8 (B) - G32-13 (GND) NORMAL mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
NORMAL mode switch (integration control and panel assembly) not pushed 10 kΩ or higher


If the result is not as specified, replace the NORMAL mode switch (integration control and panel assembly).



c.

Inspect SPORT mode switch (Integration Control and Panel Assembly)

i.
C331272C16
1.5,0.198 1.906,0.448 0.406,0.25 1.271,0.958 0.948,0.448 true 2.552,1.708 2.552,1.292 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.844,0.313 1,0.51 0.156,0.198 10 false P 2.406,1.729 2.865,1.927 0.458,0.198 10 false GND 1.563,0.25 2.021,0.448 0.458,0.198 10 false G32
*a Component without harness connected
(SPORT Mode Switch (Integration Control and Panel Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-9 (P) - G32-13 (GND) SPORT mode switch (integration control and panel assembly) being pushed and held Below 1 Ω
SPORT mode switch (integration control and panel assembly) not pushed 10 kΩ or higher


If the result is not as specified, replace the SPORT mode switch (integration control and panel assembly).



d.

Inspect the illumination:

i.
C331272C21
1.49,0.167 1.896,0.427 0.406,0.26 0.844,1 0.938,0.438 0.938,0.438 1.063,0.438 true 2.542,1 2.667,0.438 2.667,0.438 2.823,0.438 true 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 2.865,0.365 3.271,0.635 0.406,0.271 10 false ILL- 1.094,0.344 1.708,0.542 0.615,0.198 10 false ILL+ 1.563,0.219 2.021,0.417 0.458,0.198 10 false G32
*a Component without harness connected
(Integration Control and Panel Assembly)


Apply battery voltage to the integration control and panel assembly and check that the switch illuminates.

OK:
Condition Specified Condition
Battery positive (+) → G32-12 (ILL+)
Battery negative (-) →G32-1 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch.