The power back door system troubleshooting procedure is based on the premise that the entry and start system (for Entry Function, HV Model) is operating normally. Check the power back door system first before troubleshooting the power back door system.
Use the following procedure to troubleshoot the power back door system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
A simple method to determine whether the auxiliary battery is discharged is to operate the horn.
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for LIN communication system DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| LIN DTC is not output | A |
| LIN DTC is output | B |
A
B
Use the GTS to check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output | B |
A
B
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>DTC CHECK / CLEAR
Clear the DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>DTC CHECK / CLEAR
Recheck for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>DIAGNOSTIC TROUBLE CODE CHART
Refer to Problem Symptoms Table.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Operation Check
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>OPERATION CHECK
Terminals of ECU
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>TERMINALS OF ECU
Data List / Active Test
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| NEXT |
NEXT
Check whether the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) auxiliary battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has been performed.
| Result | Proceed to |
|---|---|
| The replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) auxiliary battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has been performed. | A |
| The replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU, the disconnection of the cable of the negative (-) auxiliary battery terminal with the back door open, or the removal and installation or replacement of the power source system fuses has not been performed. | B |
A
B
Initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT