Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370840 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System)  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives a reverse shift position signal from the back-up light switch assembly.

WIRING DIAGRAM

E265477E92
5.427,1.104 5.844,1.292 0.417,0.188 10 false RL 5.167,1 5.427,1.188 0.26,0.188 10 false 27 5.177,2.052 6.115,2.24 0.938,0.188 10 false G25*1, H4*2 5.177,2.219 6.375,2.583 1.198,0.365 10 false Clearance Warning ECU assembly 0.104,2.135 2.521,2.313 2.417,0.177 10 false *1: for LHD 0.104,2.427 2.938,2.625 2.833,0.198 10 false *2: for RHD 0.24,1.104 2.927,1.365 2.688,0.26 10 false from Back-up Light Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK BACK-UP LIGHT
a.

Check that the back-up light comes on.

OK:

The back-up light comes on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the clearance warning ECU assembly connector.


b.
E309541C22
0.99,0.271 1.396,0.5 0.406,0.229 1.854,0.26 2.24,0.5 0.385,0.24 1.75,1.75 1.583,1.75 1.583,1.75 1.448,1.177 true 1.063,0.313 1.396,0.521 0.333,0.208 10 false G25 1.958,0.302 2.438,0.51 0.479,0.208 10 false H4 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 2.292,0.323 2.604,0.521 0.313,0.198 10 false *B 1.823,1.677 2.135,1.875 0.313,0.198 10 false RL 1.469,0.313 1.781,0.51 0.313,0.198 10 false *A
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
G25-27 (RL) - Body ground Ignition switch ON
Shift lever in any position other than R
Below 1 V
G25-27 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
H4-27 (RL) - Body ground Ignition switch ON
Shift lever in any position other than R
Below 1 V
H4-27 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR