Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370840 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System)  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E283774E10
0.635,0.823 1.979,1.063 1.344,0.24 10 false from IG1 NO.1 Relay 3.177,0.969 4.094,1.135 0.917,0.167 10 false ECU-IG1 NO.4 5.375,0.781 5.583,0.948 0.208,0.167 10 false IG 5.365,1.323 5.573,1.49 0.208,0.167 10 false E 5.083,1.885 6.042,2.104 0.958,0.219 10 false G25*1, H4*2 5.094,2.052 6.615,2.542 1.521,0.49 10 false Clearance Warning ECU Assembly 5.115,0.688 5.323,0.854 0.208,0.167 10 false 1 5.063,1.24 5.271,1.406 0.208,0.167 10 false 30 0.25,2.063 2.729,2.292 2.479,0.229 10 false *1: for LHD and Manual Transaxle 0.25,2.344 3.198,2.625 2.948,0.281 10 false *2: except LHD and Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
E309541C24
1,0.271 1.396,0.5 0.396,0.229 1.854,0.26 2.24,0.5 0.385,0.24 2.146,1.823 2.01,1.823 2.01,1.823 1.781,1.177 true 0.479,0.99 0.396,0.49 0.396,0.49 0.229,0.49 true 1.073,0.313 1.458,0.5 0.385,0.188 10 false G25 1.958,0.302 2.438,0.51 0.479,0.208 10 false H4 1.438,0.323 1.75,0.521 0.313,0.198 10 false *A 2.292,0.323 2.604,0.521 0.313,0.198 10 false *B 2.24,1.74 2.552,1.938 0.313,0.198 10 false E 0.052,0.417 0.365,0.615 0.313,0.198 10 false IG 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*A for LHD and Manual Transaxle
*B except LHD and Manual Transaxle
*a Front view of wire harness connector
(to Clearance Warning ECU)


Disconnect the clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and Manual Transaxle:
Tester Connection Condition Specified Condition
G25-30 (E) - Body ground Always Below 1 Ω

except LHD and Manual Transaxle:
Tester Connection Condition Specified Condition
H4-30 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD and Manual Transaxle:
Tester Connection Switch Condition Specified Condition
G25-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G25-1 (IG) - Body ground Ignition switch off Below 1 V

except LHD and Manual Transaxle:
Tester Connection Switch Condition Specified Condition
H4-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H4-1 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR