Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM (for A25A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371962 STOP AND START SYSTEM(for A25A-FKS) Y

STOP AND START  STOP AND START SYSTEM(for A25A-FKS)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V (ignition switch off)


HINT:

If the battery voltage is below 11 V, recharge or replace the battery and initialize* the integrated current value using the GTS.

·

*: Use the GTS to perform Integrated Current Value Initialization.

Click here

·

If the Data List item "Integrated Current" is 0 A-sec or higher, it is not necessary to perform initialization.



HINT:
·

If the auxiliary battery voltage is below 11 V, recharge or replace the auxiliary battery. Until charging current decreases to 5 A or less, if integrated current value still does not increase to threshold value*1 or higher, initialize integrated current value*2.

-

*1: Refer to Description of Integrated Current Value Threshold

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>SYSTEM DESCRIPTION

-

*2: Using the GTS, perform Integrated Current Value Initialization.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION


·

When the battery is replaced, even if stop and start control operates immediately after replacement, stop and start control prohibition may temporarily continue due to charging capacity learning that occurs within several trips.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC AND FREEZE FRAME DATA*
4.CHECK DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392

b.

Check for freeze frame data.

HINT:

Record or print DTCs and freeze frame data if necessary.



c.

Clear the DTCs and freeze frame data.

Powertrain > Stop and Start > Clear DTCs
50002 392

d.

Recheck for DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
HINT:

If any DTCs for the CAN communication system are output, troubleshoot those DTCs first.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

5.REFER TO PROBLEM SYMPTOMS TABLE

B

5.REFER TO PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B




A

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

7.REPAIR OR REPLACE
6.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

7.REPAIR OR REPLACE
7.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

8.CONFIRMATION TEST
8.CONFIRMATION TEST
a.

Warm up the engine.


b.

Turn the air conditioning system off.


c.

Drive the vehicle for 5 to 40 minutes.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle and confirm that the engine is stopped by stop and start control when all of the following conditions are met:

·

Steering wheel centered

·

Shift lever in D

·

Brake pedal depressed

·

Stop and start indicator illuminated


HINT:

If the engine is not stopped by stop and start control, air fuel ratio learning and idle speed learning are necessary. Allow the engine to idle for 3 minutes and check that the engine idle speed is within 50 rpm of the target idle speed.



e.

Move the shift lever to N and confirm that the engine starts.


Result:
Proceed to
NEXT



NEXT

END