Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for M20A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371963 STOP AND START SYSTEM(for M20A-FKS) C

STOP AND START  STOP AND START SYSTEM(for M20A-FKS)  P061519  Starter Relay Circuit Current Above Threshold  


DESCRIPTION

for Continuously variable transaxle:

When the engine is started by stop and start control, the engine stop and start ECU controls the starter assembly by activating the ST NO. 1 relay (for starter pinion operation) via voltage from terminal STA and then, using its built-in starter delay circuit, activating the ST NO. 2 relay (for starter motor operation) via voltage from terminal STA2.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P061519 and blinks the stop and start cancel indicator.

for Manual transaxle:

When the engine is started by stop and start control, the engine stop and start ECU controls the starter assembly by activating the ST NO. 1 relay via voltage from terminal STA.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P061519 and blinks the stop and start cancel indicator.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P061519 Starter Relay Circuit Current Above Threshold Both of the following conditions are met for 1 second (1 trip detection logic):
·

Ignition switch ON.

·

Overcurrent to ST NO. 1 relay or ST NO. 2 relay* is detected.


·

Wire harness or connector

·

ST NO. 1 relay

·

ST NO. 2 relay*

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0617

*: for Continuously variable transaxle

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

for Continuously variable transaxle:

Depress the brake pedal and stop the vehicle.

for Manual transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


h.

Keep the engine stopped by stop and start control for 1 second or more. (for Continuously variable transaxle: Keep the shift lever in D.)


i.

for Continuously variable transaxle:

Release the brake pedal with the shift lever in D to start the engine.

for Manual transaxle:

Depress the clutch pedal and start the engine.


j.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

for Continuously variable transaxle:

Depress the brake pedal and stop the vehicle.

for Manual transaxle:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for Continuously variable transaxle: Keep the shift lever in D.)


f.

for Continuously variable transaxle:

Release the brake pedal with the shift lever in D to start the engine.

for Manual transaxle:

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

w/ Entry and Start System


A434160E01
0.76,2.729 1.99,2.927 1.229,0.198 10 false ST NO. 1 0.76,3.208 1.99,3.406 1.229,0.198 10 false ST NO. 2 1.792,7.99 3.021,8.188 1.229,0.198 10 false ECM 0.531,7.01 1.76,7.208 1.229,0.198 10 false Battery 0.333,8.438 2.531,8.667 2.198,0.229 10 false : CAN Communication Line 2.448,5.583 3.677,5.781 1.229,0.198 10 false ST NO. 2 2.427,4.219 3.656,4.417 1.229,0.198 10 false ST NO. 1 4.115,2.313 5.344,2.51 1.229,0.198 10 false C31 4.115,2.469 5.094,3.063 0.979,0.594 10 false Park/Neutral Position Switch Assembly 0.677,5.385 1.906,5.583 1.229,0.198 10 false Starter Assembly 1.396,7.99 2.625,8.188 1.229,0.198 10 false A24 5.552,7.042 6.781,7.24 1.229,0.198 10 false A32 5.563,7.615 6.792,7.813 1.229,0.198 10 false A32 5.74,7.979 7.135,8.365 1.396,0.385 10 false Engine Stop and Start ECU 4.427,0.417 5.656,0.615 1.229,0.198 10 false BBC NO. 1 4.448,0.948 5.677,1.146 1.229,0.198 10 false BBC NO. 2 6,0.292 6.635,0.594 0.635,0.302 10 false BIN1 6.01,0.823 6.646,1.125 0.635,0.302 10 false BIN2 6.021,1.385 6.656,1.688 0.635,0.302 10 false CLL 6.021,2.781 6.656,3.083 0.635,0.302 10 false DGND 6.021,3.917 6.656,4.219 0.635,0.302 10 false STA 6.021,5.26 6.656,5.563 0.635,0.302 10 false STA2 5.583,1.375 6.219,1.677 0.635,0.302 10 false A34 5.583,2.771 6.219,3.073 0.635,0.302 10 false A34 5.583,0.292 6.219,0.594 0.635,0.302 10 false A33 5.583,0.813 6.219,1.115 0.635,0.302 10 false A33 5.583,3.906 6.219,4.208 0.635,0.302 10 false A34 5.583,5.26 6.219,5.563 0.635,0.302 10 false A34 0.448,1.833 1.677,2.031 1.229,0.198 10 false A15 0.438,2.01 3.365,2.229 2.927,0.219 10 false Certification ECU (Smart Key ECU Assembly) 1.448,1.375 2.677,1.573 1.229,0.198 10 false STAR 1.521,1.698 2.75,1.896 1.229,0.198 10 false STA 1.917,1.26 3.146,1.458 1.229,0.198 10 false 9 1.917,1.563 3.146,1.76 1.229,0.198 10 false 20 0.51,4.729 1.74,4.927 1.229,0.198 10 false D1 0.927,4.729 2.156,4.927 1.229,0.198 10 false B 1.167,4.396 2.396,4.594 1.229,0.198 10 false SL1 1.167,4.938 2.396,5.135 1.229,0.198 10 false SL2 1.594,4.406 2.823,4.604 1.229,0.198 10 false C43 1.594,4.948 2.823,5.146 1.229,0.198 10 false C43 0.583,4.5 1.813,4.698 1.229,0.198 10 false 1 1.698,4.177 2.927,4.375 1.229,0.198 10 false 2 1.688,4.708 2.917,4.906 1.229,0.198 10 false 1 2.104,6.188 3.333,6.385 1.229,0.198 10 false STA 2.063,6.594 3.292,6.792 1.229,0.198 10 false NSW 2,7.031 3.229,7.229 1.229,0.198 10 false CANH 2.01,7.615 3.24,7.813 1.229,0.198 10 false CANL 6.031,7.615 6.76,7.938 0.729,0.323 10 false CANL 6,7.031 6.531,7.313 0.531,0.281 10 false CANH 4.542,0.146 5.042,0.458 0.5,0.313 10 false 1 4.542,0.688 5.042,1 0.5,0.313 10 false 1 4.927,0.146 5.427,0.458 0.5,0.313 10 false 2 4.958,0.698 5.458,1.01 0.5,0.313 10 false 2 5.688,0.063 6.188,0.375 0.5,0.313 10 false 3 5.677,0.594 6.177,0.906 0.5,0.313 10 false 1 5.646,1.146 6.146,1.458 0.5,0.313 10 false 17 5.677,2.552 6.177,2.865 0.5,0.313 10 false 6 5.635,3.677 6.135,3.99 0.5,0.313 10 false 21 5.635,5.042 6.135,5.354 0.5,0.313 10 false 23 5.594,6.813 6.094,7.125 0.5,0.313 10 false 13*1 5.615,7.385 6.115,7.698 0.5,0.313 10 false 14*1 2.281,3.458 3.51,3.656 1.229,0.198 10 false 3 2.302,4.813 3.531,5.01 1.229,0.198 10 false 3 2.302,3.781 3.531,3.979 1.229,0.198 10 false 1 2.302,5.135 3.531,5.333 1.229,0.198 10 false 1 3.042,3.458 4.271,3.656 1.229,0.198 10 false 5 3.042,4.823 4.271,5.021 1.229,0.198 10 false 5 3.021,3.792 4.25,3.99 1.229,0.198 10 false 2 3.031,5.146 4.26,5.344 1.229,0.198 10 false 2 2.5,6.49 3,6.802 0.5,0.313 10 false 23 2.49,6.854 2.99,7.167 0.5,0.313 10 false 8 2.479,6.083 2.979,6.396 0.5,0.313 10 false 30 2.49,7.427 2.99,7.74 0.5,0.313 10 false 18 3.76,2.469 4.99,2.667 1.229,0.198 10 false B 3.76,2.792 4.99,2.99 1.229,0.198 10 false L 3.781,2.25 5.01,2.448 1.229,0.198 10 false 4 3.771,3.021 5,3.219 1.229,0.198 10 false 5 5.125,7.031 6.354,7.229 1.229,0.198 10 false G62 5.115,7.604 6.344,7.802 1.229,0.198 10 false G62 5.115,6.792 5.615,7.104 0.5,0.313 10 false 13*2 5.115,7.396 5.615,7.708 0.5,0.313 10 false 14*2 3.271,8.094 5.469,8.323 2.198,0.229 10 false *1: for LHD 3.271,8.396 5.469,8.625 2.198,0.229 10 false *2: for RHD 0.156,0.031 2.531,0.385 2.375,0.354 10 false for Continuously variable transaxle:

A436048E01
0.76,2.729 1.99,2.927 1.229,0.198 10 false ST NO. 1 1.792,7.99 3.021,8.188 1.229,0.198 10 false ECM 0.531,7.01 1.76,7.208 1.229,0.198 10 false Battery 0.333,8.438 2.531,8.667 2.198,0.229 10 false : CAN Communication Line 2.438,4.802 3.667,5 1.229,0.198 10 false ST NO. 1 4.115,2.313 5.344,2.51 1.229,0.198 10 false A81 4.115,2.469 5.094,3.063 0.979,0.594 10 false Clutch Switch Assembly 0.656,4.917 1.885,5.115 1.229,0.198 10 false Starter Assembly 1.396,7.99 2.625,8.188 1.229,0.198 10 false A24 5.552,7.042 6.781,7.24 1.229,0.198 10 false A32 5.563,7.615 6.792,7.813 1.229,0.198 10 false A32 5.74,7.979 7.135,8.365 1.396,0.385 10 false Engine Stop and Start ECU 4.427,0.417 5.656,0.615 1.229,0.198 10 false BBC NO. 1 4.448,0.948 5.677,1.146 1.229,0.198 10 false BBC NO. 2 6,0.292 6.635,0.594 0.635,0.302 10 false BIN1 6.01,0.823 6.646,1.125 0.635,0.302 10 false BIN2 6.021,1.385 6.656,1.688 0.635,0.302 10 false CLL 6.021,2.781 6.656,3.083 0.635,0.302 10 false DGND 6.01,4.458 6.646,4.76 0.635,0.302 10 false STA 5.583,1.375 6.219,1.677 0.635,0.302 10 false A34 5.583,2.771 6.219,3.073 0.635,0.302 10 false A34 5.583,0.292 6.219,0.594 0.635,0.302 10 false A33 5.583,0.813 6.219,1.115 0.635,0.302 10 false A33 5.573,4.458 6.208,4.76 0.635,0.302 10 false A34 0.448,1.833 1.677,2.031 1.229,0.198 10 false A15 0.438,2.01 3.365,2.229 2.927,0.219 10 false Certification ECU (Smart Key ECU Assembly) 1.448,1.375 2.677,1.573 1.229,0.198 10 false STAR 1.521,1.698 2.75,1.896 1.229,0.198 10 false STA 1.917,1.26 3.146,1.458 1.229,0.198 10 false 9 1.917,1.563 3.146,1.76 1.229,0.198 10 false 20 0.531,4.458 1.76,4.656 1.229,0.198 10 false D1 0.917,4.469 2.146,4.667 1.229,0.198 10 false B 1.156,4.156 2.385,4.354 1.229,0.198 10 false SL1 1.583,4.135 2.813,4.333 1.229,0.198 10 false C43 0.583,4.229 1.813,4.427 1.229,0.198 10 false 1 1.656,3.906 2.885,4.104 1.229,0.198 10 false 2 2.104,6.188 3.333,6.385 1.229,0.198 10 false STA 2.063,6.594 3.292,6.792 1.229,0.198 10 false NSW 2,7.031 3.229,7.229 1.229,0.198 10 false CANH 2.01,7.615 3.24,7.813 1.229,0.198 10 false CANL 6.031,7.615 6.76,7.938 0.729,0.323 10 false CANL 6,7.031 6.531,7.313 0.531,0.281 10 false CANH 4.542,0.146 5.042,0.458 0.5,0.313 10 false 1 4.542,0.688 5.042,1 0.5,0.313 10 false 1 4.927,0.146 5.427,0.458 0.5,0.313 10 false 2 4.958,0.698 5.458,1.01 0.5,0.313 10 false 2 5.688,0.063 6.188,0.375 0.5,0.313 10 false 3 5.677,0.594 6.177,0.906 0.5,0.313 10 false 1 5.646,1.146 6.146,1.458 0.5,0.313 10 false 17 5.677,2.552 6.177,2.865 0.5,0.313 10 false 6 5.625,4.198 6.125,4.51 0.5,0.313 10 false 21 5.594,6.813 6.094,7.125 0.5,0.313 10 false 13*1 5.615,7.385 6.115,7.698 0.5,0.313 10 false 14*1 2.302,4.021 3.531,4.219 1.229,0.198 10 false 3 2.323,4.354 3.552,4.552 1.229,0.198 10 false 1 3.052,4.042 4.281,4.24 1.229,0.198 10 false 5 3.063,4.365 4.292,4.563 1.229,0.198 10 false 2 2.5,6.49 3,6.802 0.5,0.313 10 false 23 2.49,6.854 2.99,7.167 0.5,0.313 10 false 8 2.479,6.083 2.979,6.396 0.5,0.313 10 false 30 2.49,7.427 2.99,7.74 0.5,0.313 10 false 18 3.781,2.25 5.01,2.448 1.229,0.198 10 false 1 3.771,3.021 5,3.219 1.229,0.198 10 false 2 5.125,7.031 6.354,7.229 1.229,0.198 10 false G62 5.115,7.604 6.344,7.802 1.229,0.198 10 false G62 5.115,6.792 5.615,7.104 0.5,0.313 10 false 13*2 5.115,7.396 5.615,7.708 0.5,0.313 10 false 14*2 3.271,8.094 5.469,8.323 2.198,0.229 10 false *1: for LHD 3.271,8.396 5.469,8.625 2.198,0.229 10 false *2: for RHD 0.156,0.031 2.531,0.385 2.375,0.354 10 false for Manual transaxle:


w/o Entry and Start System


A434161E01
0.344,8.438 2.167,8.677 1.823,0.24 10 false : CAN Communication Line 0.521,7.01 2.344,7.25 1.823,0.24 10 false Battery 0.677,5.375 2.5,5.615 1.823,0.24 10 false Starter Assembly 1.531,1.521 2.01,1.802 0.479,0.281 10 false AM2 0.792,3.198 2.615,3.438 1.823,0.24 10 false ST NO. 2 0.813,2.729 2.635,2.969 1.823,0.24 10 false ST NO. 1 0.656,1.531 2.479,1.771 1.823,0.24 10 false J/B-B 2.313,1.76 3.833,2.333 1.521,0.573 10 false Ignition or Starter Switch Assembly 2.021,1.625 4.323,1.906 2.302,0.281 10 false G28 0.927,4.74 2.75,4.979 1.823,0.24 10 false B 0.51,4.729 2.333,4.969 1.823,0.24 10 false D1 1.594,4.406 3.417,4.646 1.823,0.24 10 false C43 1.594,4.938 3.417,5.177 1.823,0.24 10 false C43 1.677,4.177 3.5,4.417 1.823,0.24 10 false 2 1.677,4.719 3.5,4.958 1.823,0.24 10 false 1 0.583,4.521 2.406,4.76 1.823,0.24 10 false 1 4.458,0.427 5.51,0.792 1.052,0.365 10 false BBC NO. 1 4.479,0.958 5.531,1.323 1.052,0.365 10 false BBC NO. 2 4.531,0.146 4.833,0.406 0.302,0.26 10 false 1 4.531,0.688 4.833,0.948 0.302,0.26 10 false 1 4.958,0.146 5.26,0.406 0.302,0.26 10 false 2 4.969,0.698 5.271,0.958 0.302,0.26 10 false 2 5.583,0.281 6.635,0.646 1.052,0.365 10 false A33 5.594,0.823 6.646,1.188 1.052,0.365 10 false A33 5.594,1.375 6.646,1.74 1.052,0.365 10 false A34 5.583,2.771 6.635,3.135 1.052,0.365 10 false A34 5.594,3.906 6.646,4.271 1.052,0.365 10 false A34 5.604,5.271 6.656,5.635 1.052,0.365 10 false A34 5.563,7.031 6.615,7.396 1.052,0.365 10 false A32 5.552,7.615 6.604,7.979 1.052,0.365 10 false A32 2.417,4.219 4.24,4.458 1.823,0.24 10 false ST NO. 1 2.427,5.573 4.25,5.813 1.823,0.24 10 false ST NO. 2 2.302,3.469 4.125,3.708 1.823,0.24 10 false 3 2.302,3.792 4.125,4.031 1.823,0.24 10 false 1 3.031,3.469 4.854,3.708 1.823,0.24 10 false 5 3.031,3.792 4.854,4.031 1.823,0.24 10 false 2 2.302,4.823 4.125,5.063 1.823,0.24 10 false 3 2.292,5.146 4.115,5.385 1.823,0.24 10 false 1 3.031,4.833 4.854,5.073 1.823,0.24 10 false 5 3.031,5.156 4.854,5.396 1.823,0.24 10 false 2 5.729,7.99 7.104,8.385 1.375,0.396 10 false Engine Stop and Start ECU 6.01,7.042 6.729,7.385 0.719,0.344 10 false CANH 6.021,7.604 6.74,7.948 0.719,0.344 10 false CANL 6.021,5.26 6.74,5.604 0.719,0.344 10 false STA2 6.021,3.906 6.74,4.25 0.719,0.344 10 false STA 6.021,2.792 6.74,3.135 0.719,0.344 10 false DGND 6.031,1.385 6.75,1.729 0.719,0.344 10 false CLL 6.031,0.833 6.75,1.177 0.719,0.344 10 false BIN2 6.021,0.292 6.74,0.635 0.719,0.344 10 false BIN1 5.667,0.063 5.969,0.323 0.302,0.26 10 false 3 5.667,0.583 5.969,0.844 0.302,0.26 10 false 1 5.635,1.156 5.938,1.417 0.302,0.26 10 false 17 5.667,2.552 5.969,2.813 0.302,0.26 10 false 6 5.625,3.677 5.927,3.938 0.302,0.26 10 false 21 5.646,5.052 5.948,5.313 0.302,0.26 10 false 23 5.583,6.813 5.885,7.073 0.302,0.26 10 false 13*1 5.552,7.396 5.854,7.656 0.302,0.26 10 false 14*1 1.906,8.021 2.958,8.385 1.052,0.365 10 false ECM 1.5,8.021 2.552,8.385 1.052,0.365 10 false A24 1.969,7.042 2.688,7.385 0.719,0.344 10 false CANH 1.99,7.615 2.708,7.958 0.719,0.344 10 false CANL 2.5,6.854 2.802,7.115 0.302,0.26 10 false 8 2.5,7.427 2.802,7.688 0.302,0.26 10 false 18 2.115,6.198 2.833,6.542 0.719,0.344 10 false STA 2.042,6.604 2.76,6.948 0.719,0.344 10 false NSW 2.49,6.083 2.792,6.344 0.302,0.26 10 false 30 2.5,6.5 2.802,6.76 0.302,0.26 10 false 23 4.115,2.438 5.167,2.802 1.052,0.365 10 false C31 4.115,2.615 5.094,3.219 0.979,0.604 10 false Park/Neutral Position Switch Assembly 3.771,2.813 4.823,3.177 1.052,0.365 10 false L 3.75,2.458 4.802,2.823 1.052,0.365 10 false B 3.771,2.25 4.073,2.51 0.302,0.26 10 false 4 3.75,3.042 4.052,3.302 0.302,0.26 10 false 5 2.167,1.25 4.469,1.531 2.302,0.281 10 false 7 2.354,1.271 4.177,1.51 1.823,0.24 10 false AM1 3.125,1.25 4.948,1.49 1.823,0.24 10 false ST1 3.479,1.25 5.781,1.531 2.302,0.281 10 false 5 1.167,4.396 2.99,4.635 1.823,0.24 10 false SL1 1.156,4.938 2.979,5.177 1.823,0.24 10 false SL2 5.094,7.021 6.146,7.385 1.052,0.365 10 false G62 5.104,7.604 6.156,7.969 1.052,0.365 10 false G62 5.094,6.823 5.396,7.083 0.302,0.26 10 false 13*2 5.115,7.385 5.417,7.646 0.302,0.26 10 false 14*2 3.188,8 4.875,8.198 1.688,0.198 10 false *1: for LHD 3.208,8.344 4.896,8.542 1.688,0.198 10 false *2: for RHD 0.146,0.021 3.302,0.344 3.156,0.323 10 false for Continuously variable transaxle:

A436049E01
0.344,8.438 2.167,8.677 1.823,0.24 10 false : CAN Communication Line 0.521,7.01 2.344,7.25 1.823,0.24 10 false Battery 0.74,4.719 2.563,4.958 1.823,0.24 10 false Starter Assembly 1.281,1.51 1.76,1.792 0.479,0.281 10 false AM2 0.813,2.729 2.635,2.969 1.823,0.24 10 false ST NO. 1 0.531,1.531 2.354,1.771 1.823,0.24 10 false J/B-B 1.521,1.802 3.823,2.083 2.302,0.281 10 false Ignition or Starter Switch Assembly 1.604,1.656 3.906,1.938 2.302,0.281 10 false G28 0.906,4.302 2.729,4.542 1.823,0.24 10 false B 0.5,4.281 2.323,4.521 1.823,0.24 10 false D1 1.594,3.958 3.417,4.198 1.823,0.24 10 false C43 1.688,3.74 3.51,3.979 1.823,0.24 10 false 2 0.573,4.063 2.396,4.302 1.823,0.24 10 false 1 4.458,0.427 5.51,0.792 1.052,0.365 10 false BBC NO. 1 4.479,0.958 5.531,1.323 1.052,0.365 10 false BBC NO. 2 4.531,0.146 4.833,0.406 0.302,0.26 10 false 1 4.531,0.688 4.833,0.948 0.302,0.26 10 false 1 4.958,0.146 5.26,0.406 0.302,0.26 10 false 2 4.969,0.698 5.271,0.958 0.302,0.26 10 false 2 5.583,0.281 6.635,0.646 1.052,0.365 10 false A33 5.594,0.823 6.646,1.188 1.052,0.365 10 false A33 5.594,1.375 6.646,1.74 1.052,0.365 10 false A34 5.583,2.771 6.635,3.135 1.052,0.365 10 false A34 5.604,4.271 6.656,4.635 1.052,0.365 10 false A34 5.563,7.031 6.615,7.396 1.052,0.365 10 false A32 5.552,7.615 6.604,7.979 1.052,0.365 10 false A32 2.448,4.656 4.271,4.896 1.823,0.24 10 false ST NO. 1 2.313,3.813 4.135,4.052 1.823,0.24 10 false 3 2.302,4.177 4.125,4.417 1.823,0.24 10 false 1 3.042,3.833 4.865,4.073 1.823,0.24 10 false 5 3.042,4.188 4.865,4.427 1.823,0.24 10 false 2 5.729,7.99 7.104,8.385 1.375,0.396 10 false Engine Stop and Start ECU 6.01,7.042 6.729,7.385 0.719,0.344 10 false CANH 6.021,7.604 6.74,7.948 0.719,0.344 10 false CANL 6.031,4.281 6.75,4.625 0.719,0.344 10 false STA 6.021,2.792 6.74,3.135 0.719,0.344 10 false DGND 6.031,1.385 6.75,1.729 0.719,0.344 10 false CLL 6.031,0.833 6.75,1.177 0.719,0.344 10 false BIN2 6.021,0.292 6.74,0.635 0.719,0.344 10 false BIN1 5.667,0.063 5.969,0.323 0.302,0.26 10 false 3 5.667,0.583 5.969,0.844 0.302,0.26 10 false 1 5.635,1.156 5.938,1.417 0.302,0.26 10 false 17 5.667,2.552 5.969,2.813 0.302,0.26 10 false 6 5.615,4.042 5.917,4.302 0.302,0.26 10 false 21 5.583,6.813 5.885,7.073 0.302,0.26 10 false 13*1 5.552,7.396 5.854,7.656 0.302,0.26 10 false 14*1 1.906,8.021 2.958,8.385 1.052,0.365 10 false ECM 1.5,8.021 2.552,8.385 1.052,0.365 10 false A24 1.969,7.042 2.688,7.385 0.719,0.344 10 false CANH 1.99,7.615 2.708,7.958 0.719,0.344 10 false CANL 2.5,6.854 2.802,7.115 0.302,0.26 10 false 8 2.5,7.427 2.802,7.688 0.302,0.26 10 false 18 2.115,6.198 2.833,6.542 0.719,0.344 10 false STA 2.042,6.604 2.76,6.948 0.719,0.344 10 false NSW 2.49,6.083 2.792,6.344 0.302,0.26 10 false 30 2.5,6.5 2.802,6.76 0.302,0.26 10 false 23 4.115,2.438 5.167,2.802 1.052,0.365 10 false A81 4.115,2.615 5.094,3.219 0.979,0.604 10 false Clutch Switch Assembly 3.771,2.25 4.073,2.51 0.302,0.26 10 false 1 3.75,3.042 4.052,3.302 0.302,0.26 10 false 2 1.698,1.26 4,1.542 2.302,0.281 10 false 7 1.896,1.271 3.719,1.51 1.823,0.24 10 false AM1 2.656,1.26 4.479,1.5 1.823,0.24 10 false ST1 3.031,1.26 5.333,1.542 2.302,0.281 10 false 5 1.188,3.958 3.01,4.198 1.823,0.24 10 false SL1 5.094,7.021 6.146,7.385 1.052,0.365 10 false G62 5.104,7.604 6.156,7.969 1.052,0.365 10 false G62 5.094,6.823 5.396,7.083 0.302,0.26 10 false 13*2 5.115,7.385 5.417,7.646 0.302,0.26 10 false 14*2 3.188,8 4.875,8.198 1.688,0.198 10 false *1: for LHD 3.208,8.344 4.896,8.542 1.688,0.198 10 false *2: for RHD 0.146,0.021 3.302,0.344 3.156,0.323 10 false for Manual transaxle:


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

for Continuously variable transaxle:

Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE AND BBC NO. 2 FUSE)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-1 (BIN2) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
A33-3 (BIN1) - BBC NO. 1 fuse terminal 2 Always Below 1 Ω
A33-1 (BIN2) or BBC NO. 2 fuse terminal 2 - Body ground and other terminals Always 10 kΩ or higher
A33-3 (BIN1) or BBC NO. 1 fuse terminal 2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Result Proceed to
OK (for Continuously variable transaxle) A
OK (for Manual transaxle) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY AND ST NO. 2 RELAY)

B

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE OR BBC NO. 2 FUSE)

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY AND ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connectors.


b.

Remove the ST NO. 1 relay and ST NO. 2 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector. (w/ Entry and Start System)


d.

Disconnect the park/neutral position switch assembly connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A34-23 (STA2) - 2 (ST NO. 2 relay) Always Below 1 Ω
A34-21 (STA) or 2 (ST NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher
A34-23 (STA2) or 2 (ST NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher
A33-1 (BIN2) - A34-21 (STA) Always 10 kΩ or higher
A33-3 (BIN1) - A34-21 (STA) Always 10 kΩ or higher
A33-1 (BIN2) - A34-23 (STA2) Always 10 kΩ or higher
A33-3 (BIN1) - A34-23 (STA2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY OR ST NO. 2 RELAY)

3.CHECK ENGINE STOP AND START ECU
A397704C54
3.188,0.083 3.604,0.323 0.417,0.24 2.781,1.469 3.135,0.802 true 3.417,1.458 3.344,0.813 true 3.938,1.458 3.688,0.708 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 3.271,0.125 3.667,0.323 0.396,0.198 10 false A34 2.594,1.5 3.125,1.698 0.531,0.198 10 false STA2 3.302,1.5 3.833,1.698 0.531,0.198 10 false STA 3.802,1.51 4.333,1.708 0.531,0.198 10 false DGND
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - A34-6 (DGND) Always 10 kΩ or higher
A34-23 (STA2) - A34-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (ST NO. 1 RELAY AND ST NO. 2 RELAY)

NG

4.INSPECT RELAY (ST NO. 1 RELAY AND ST NO. 2 RELAY)
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


b.

Inspect the ST NO. 2 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST NO. 1 RELAY AND ST NO. 2 RELAY)

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the engine stop and start ECU connectors.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the certification ECU (smart key ECU assembly) connector. (w/ Entry and Start System)


d.

Disconnect the clutch switch assembly connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A34-21 (STA) or 2 (ST NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher
A33-1 (BIN2) - A34-21 (STA) Always 10 kΩ or higher
A33-3 (BIN1) - A34-21 (STA) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

6.CHECK ENGINE STOP AND START ECU
A397704C55
3.188,0.083 3.604,0.323 0.417,0.24 2.917,1.479 3.344,0.813 true 3.938,1.458 3.688,0.708 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 3.271,0.125 3.667,0.323 0.396,0.198 10 false A34 2.781,1.51 3.313,1.708 0.531,0.198 10 false STA 3.802,1.51 4.333,1.708 0.531,0.198 10 false DGND
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-21 (STA) - A34-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT RELAY (ST NO. 1 RELAY)

NG

7.INSPECT RELAY (ST NO. 1 RELAY)
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST NO. 1 RELAY)