A backup boost converter is built into the engine stop and start ECU.
The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.
The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.
A relay function and fuse function are provided in the backup boost converter.
If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).
When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.
The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.
*: A semiconductor fuse self resets according to electric signal.
Toyota safety sense
Tire pressure warning system
Vehicle stability control system
Power steering system
Audio and visual system
Navigation system
Panoramic view monitor system
Blind spot monitor system
Telematics system
CAN communication system
Meter / gauge system
Air conditioning system
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | Note |
|---|---|---|---|---|---|---|
| P323A19 | Backup Boost Converter "A" Circuit Current Above Threshold | The following condition continues for 1 second or more (1 trip detection logic):
·
Overcurrent is detected at the B41, B42, B43 and IG41 terminals in the engine stop and start ECU |
·
Wire harness or connector ·
Radio and display receiver assembly (w/ Display Audio System) ·
Radio receiver assembly (w/o Display Audio System) ·
Tire Pressure Warning ECU and Receiver (w/ Tire Pressure Warning System) ·
Central gateway ECU (network gateway ECU) ·
Clearance Warning ECU Assembly ·
Forward recognition camera (w/ Toyota Safety Sense) ·
Millimeter wave radar sensor assembly (w/ Toyota Safety Sense) ·
Air conditioning control assembly ·
Inner Rear View Mirror Assembly (EC Mirror) ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
for Continuously variable transaxle:
Depress the brake pedal and stop the vehicle.
for Manual transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more. (for Continuously variable transaxle: Keep the shift lever in D.)
for Continuously variable transaxle:
Release the brake pedal with the shift lever in D to start the engine.
for Manual transaxle:
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
for Continuously variable transaxle:
Depress the brake pedal and stop the vehicle.
for Manual transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control. (for Continuously variable transaxle: Keep the shift lever in D.)
for Continuously variable transaxle:
Release the brake pedal with the shift lever in D to start the engine.
for Manual transaxle:
Depress the clutch pedal and start the engine.
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
for Continuously variable transaxle:
Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.
If the fuse function of the backup boost converter operates, any systems connected to the B41, B42, B43 or IG41 terminal in the engine stop and start ECU will not operate.
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>DTC CHECK / CLEAR
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>FREEZE FRAME DATA
Disconnect the engine stop and start ECU connector.
Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-1 (BIN2) - 2 (BBC NO. 2 fuse) | Always | Below 1 Ω |
| A33-3 (BIN1) - 2 (BBC NO. 1 fuse) | Always | Below 1 Ω |
| A33-1 (BIN2) or 2 (BBC NO. 2 fuse) - Body ground and other terminals | Always | 10 kΩ or higher |
| A33-3 (BIN1) or 2 (BBC NO. 1 fuse) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the radio and display receiver assembly connector. (w/ Display Audio System)
Disconnect the radio receiver assembly connector. (w/o Display Audio System)
Disconnect the electrical key and tire pressure monitoring system receiver assembly connector. (w/ Tire Pressure Warning System)
Disconnect the central gateway ECU (network gateway ECU) connector.
Disconnect the clearance warning ECU assembly connector.
Disconnect the forward recognition camera connector. (w/ Toyota Safety Sense)
Disconnect the millimeter wave radar sensor assembly connector. (w/ Toyota Safety Sense)
Disconnect the blind spot monitor sensor LH connector.
Disconnect the blind spot monitor sensor RH connector.
Disconnect the air conditioning control assembly connector.
Disconnect the inner rear view mirror assembly connector. (w/ EC Mirror)
Disconnect the inner rear view mirror assembly connector. (w/ Digital Inner Mirror)
Disconnect the instrument panel junction block assembly (main body ECU (multiplex network body ECU)) connector. (for Manual transaxle)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-12 (B42) - G3-4 (+B1)*1 | Always | Below 1 Ω |
| A32-12 (B42) - G66-4 (+B1)*2 | Always | Below 1 Ω |
| A32-2 (B41) - M8-7 (+B)*3 | Always | Below 1 Ω |
| A32-3 (IG41) - M8-1 (IG)*3 | Always | Below 1 Ω |
| A32-3 (IG41) - G72-11 (IG1) | Always | Below 1 Ω |
| A32-3 (IG41) - H4-1 (IG) | Always | Below 1 Ω |
| A32-3 (IG41) - P8-7 (IGB)*4 | Always | Below 1 Ω |
| A32-3 (IG41) - B9-8 (IGB)*4 | Always | Below 1 Ω |
| A32-3 (IG41) - Q1-5 (BLB) | Always | Below 1 Ω |
| A32-3 (IG41) - Q13-5 (BRB) | Always | Below 1 Ω |
| A32-3 (IG41) - G24-9 (IG+) | Always | Below 1 Ω |
| A32-3 (IG41) - P2-4 (IG)*5 | Always | Below 1 Ω |
| A32-3 (IG41) - P3-1 (IG)*6 | Always | Below 1 Ω |
| A32-3 (IG41) - 4A-15*8 | Always | Below 1 Ω |
| A32-11 (B43) - P1-6 (+B)*7 | Always | Below 1 Ω |
| A32-11 (B43) - H7-10 (+B) | Always | Below 1 Ω |
| A32-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or G72-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or H4-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or B9-8 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or G24-9 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or 4A-15*8 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-11 (B43) or H7-10 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G62-12 (B42) - G3-4 (+B1)*1 | Always | Below 1 Ω |
| G62-12 (B42) - G66-4 (+B1)*2 | Always | Below 1 Ω |
| G62-2 (B41) - M8-7 (+B)*3 | Always | Below 1 Ω |
| G62-3 (IG41) - M8-1 (IG)*3 | Always | Below 1 Ω |
| G62-3 (IG41) - G72-11 (IG1) | Always | Below 1 Ω |
| G62-3 (IG41) - H4-1 (IG) | Always | Below 1 Ω |
| G62-3 (IG41) - P8-7 (IGB)*4 | Always | Below 1 Ω |
| G62-3 (IG41) - Q1-5 (BLB) | Always | Below 1 Ω |
| G62-3 (IG41) - Q13-5 (BRB) | Always | Below 1 Ω |
| G62-3 (IG41) - G24-9 (IG+) | Always | Below 1 Ω |
| G62-3 (IG41) - P2-4 (IG)*5 | Always | Below 1 Ω |
| G62-3 (IG41) - P3-1 (IG)*6 | Always | Below 1 Ω |
| G62-3 (IG41) - 4A-15*8 | Always | Below 1 Ω |
| G62-11 (B43) - P1-6 (+B)*7 | Always | Below 1 Ω |
| G62-11 (B43) - H7-10 (+B) | Always | Below 1 Ω |
| G62-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or G72-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or H4-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or G24-9 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or 4A-15*8 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-11 (B43) or H7-10 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
*1: w/ Display Audio System
*2: w/o Display Audio System
*3: w/ Tire Pressure Warning System
*4: w/ Toyota Safety Sense
*5: w/ Forward Recognition Camera
*6: w/o Forward Recognition Camera
*7: w/ Digital Inner Mirror
*8: for Manual transaxle
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | for LHD | *2 | for RHD |
| *a | Component without harness connected
(Engine Stop and Start ECU) |
- | - |
Disconnect the engine stop and start ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32*1-2 (B41) - A34-6 (DGND)
G62*2-2 (B41) - A34-6 (DGND) |
Always | 10 kΩ or higher |
| A32*1-3 (IG41) - A34-6 (DGND)
G62*2-3 (IG41) - A34-6 (DGND) |
Always | 10 kΩ or higher |
| A32*1-11 (B43) - A34-6 (DGND)
G62*2-11 (B43) - A34-6 (DGND) |
Always | 10 kΩ or higher |
| A32*1-12 (B42) - A34-6 (DGND)
G62*2-12 (B42) - A34-6 (DGND) |
Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41, B42, B43 or IG41 terminal circuit of the engine stop and start ECU.
| Result | Proceed to |
|---|---|
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. | A |
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. | B |
A
B