Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for M20A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371963 STOP AND START SYSTEM(for M20A-FKS) U

STOP AND START  STOP AND START SYSTEM(for M20A-FKS)  TERMINALS OF ECU  


ENGINE STOP AND START ECU


B412468E30
4.729,0.052 5.156,0.302 0.427,0.25 3.219,0.208 3.646,0.458 0.427,0.25 1.563,0.208 1.99,0.458 0.427,0.25 4.74,0.333 5.167,0.583 0.427,0.25 3.323,0.26 3.781,0.458 0.458,0.198 10 false A34 1.656,0.25 2.115,0.448 0.458,0.198 10 false A33 4.76,0.083 5.25,0.354 0.49,0.271 10 false A32*1 4.771,0.385 5.375,0.708 0.604,0.323 10 false G62*2 5.438,0.094 6.354,0.323 0.917,0.229 10 false *1: for LHD 5.458,0.375 6.188,0.604 0.729,0.229 10 false *2: for RHD

a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A33-1 (BIN2) - Body ground W - Body ground Battery Always 9.5 to 14 V
A33-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
A33-3 (BIN1) - Body ground B - Body ground Battery Always 9.5 to 14 V
A33-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
A34-1 (+B) - Body ground R - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A34-6 (DGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A34-10 (NE) - Body ground BR - Body ground Engine speed signal from ECM Always 10 kΩ or higher
A32*1-13 (CANH) - Body ground
G62*2-13 (CANH) - Body ground
R - Body ground CAN communication Always 200 Ω or higher
A32*1-14 (CANL) - Body ground
G62*2-14 (CANL) - Body ground
W - Body ground CAN communication Always 200 Ω or higher
A32*1-18 (IG2) - Body ground
G62*2-18 (IG2) - Body ground
R*1 - Body ground
B*2 - Body ground
Ignition switch signal Ignition switch ON 9.5 to 14 V
A32*1-19 (ACC) - Body ground
G62*2-19 (ACC) - Body ground
G - Body ground Ignition switch signal Ignition switch ACC 9.5 to 14 V
A32*1-21 (IG1) - Body ground
G62*2-21 (IG1) - Body ground
LG - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the engine stop and start ECU connectors.


d.

Measure the resistance, voltage and pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A33-6 (OP21)*3 - A34-6 (DGND) GR - W-B Oil pump with motor assembly drive power source signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


10.5 to 16 V
A34-3 (BRE2) - Body ground V - Body ground Ground (vacuum sensor assembly) Always Below 1 Ω
A34-7 (BNT1) - A34-6 (DGND) Y - W-B Engine hood courtesy switch (hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


Below 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A34-9 (OPM1)*3 - A34-6 (DGND) R - W-B Oil pump with motor assembly directions signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


Pulse generation
(See waveform 1)
A34-10 (NE) - A34-6 (DGND) BR - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(See waveform 2)
A34-13 (PB) - A34-3 (BRE2) SB - V Vacuum sensor assembly signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied to vacuum sensor assembly


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (450 mmHg, 17.7 in.Hg) applied to vacuum sensor assembly


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly


3.4 to 3.8 V
A34-14 (BRVC) - A34-6 (DGND) W - W-B Vacuum sensor assembly power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A34-17 (CLL)*3 - A34-6 (DGND) R - W-B Park/Neutral position switch assembly signal
·

Ignition switch ON

·

Shift lever not in P or N


8 to 14 V
·

Ignition switch ON

·

Shift lever in P or N


Below 3.0 V
A34-17 (CLL)*4 - A34-6 (DGND) R - W-B Clutch start switch assembly signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A34-8 (TMN)*4 - A34-25 (TME2)*4 L - B Neutral position switch signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
A34-26 (TMVC)*4 - A34-6 (DGND) W - W-B Neutral position switch power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A34-19 (DON2) - A34-6 (DGND) L - W-B External backup boost converter (eco run vehicle converter assembly) signal Engine running Pulse generation
(See Waveform 3)
A34-21 (STA) - A34-6 (DGND) LG - W-B Starter pinion operation signal Cranking 6.0 V or more
A34-23 (STA2)*3 - A34-6 (DGND) G - W-B Starter motor operation signal Cranking 6.0 V or more
A34-27 (NOPM)*3 - A34-6 (DGND) LG - W-B Oil pump with motor assembly speed signal One of the following conditions is met:
·

Engine stopped by stop and start system control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed


Pulse generation
(See Waveform 4)
A32*1-1 (IG31) - A34-6 (DGND)
G62*2-1 (IG31) - A34-6 (DGND)
LA-V - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
A32*1-2 (B41) - A34-6 (DGND)
G62*2-2 (B41) - A34-6 (DGND)
LA-L - W-B Backup boost converter signal Always 10.5 to 16 V
A32*1-3 (IG41) - A34-6 (DGND)
G62*2-3 (IG41) - A34-6 (DGND)
L*1 - W-B
B*2 - W-B
Backup boost converter signal Ignition switch ON 10.5 to 16 V
A32*1-5 (ECAN) - A34-6 (DGND)
G62*2-5 (ECAN) - A34-6 (DGND)
V*1 - W-B
B*2 - W-B
Stop and start system cancel switch (eco run cancel switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (eco run cancel switch assembly) pressed


Below 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (eco run cancel switch assembly) not pressed


8 to 14 V
A32*1-6 (IG11) - A34-6 (DGND)
G62*2-6 (IG11) - A34-6 (DGND)
SB - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
A32*1-10 (IG12) - A34-6 (DGND)
G62*2-10 (IG12) - A34-6 (DGND)
W*1 - W-B
B*2 - W-B
Backup boost converter signal Ignition switch ON 10.5 to 16 V
A32*1-26 (IG13) - A34-6 (DGND)
G62*2-26 (IG13) - A34-6 (DGND)
GR - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
A32*1-16 (B12) - A34-6 (DGND)
G62*2-16 (B12) - A34-6 (DGND)
BR - W-B Backup boost converter signal Always 10.5 to 16 V
A32*1-12 (B42) - A34-6 (DGND)
G62*2-12 (B42) - A34-6 (DGND)
LA-B*1 - W-B
BE*2 - W-B
Backup boost converter signal Always 10.5 to 16 V
A32*1-11 (B43) - A34-6 (DGND)
G62*2-11 (B43) - A34-6 (DGND)
GR - W-B Backup boost converter signal Always 10.5 to 16 V
A32*1-18 (IG2) - A34-6 (DGND)
G62*2-18 (IG2) - A34-6 (DGND)
R*1 - W-B
B*2 - W-B
Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
A32*1-19 (ACC) - A34-6 (DGND)
G62*2-19 (ACC) - A34-6 (DGND)
G - W-B Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
A32*1-21 (IG1) - A34-6 (DGND)
G62*2-21 (IG1) - A34-6 (DGND)
LG - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
A32*1-24 (AC41) - A34-6 (DGND)
G62*2-24 (AC41) - A34-6 (DGND)
BE - W-B Backup boost converter signal Ignition switch ACC 10.5 to 16 V
A32*1-25 (IL41) - A34-6 (DGND)
G62*2-25 (IL41) - A34-6 (DGND)
Y*1 - W-B
L*2 - W-B
Backup boost converter signal Headlight dimmer switch (light control switch) in tail or head position 10.5 to 16 V

*1: for LHD

*2: for RHD

*3: for Continuously variable transaxle

*4: for Manual transaxle



e.
A329962E08
0.073,0.052 1.302,0.25 1.229,0.198 10 false 5 V/DIV. 1.135,2 1.958,2.177 0.823,0.177 10 false 5 ms./DIV. 2.885,1.25 3.344,1.448 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection A34-9 (OPM1)*3 - A34-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition One of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed




f.
A318633E03
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Waveform 2

Item Content
Tester Connection A34-10 (NE) - A34-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


g.
A199267E07
2.917,1.198 3.375,1.396 0.458,0.198 10 false GND 0.24,0.083 1.469,0.281 1.229,0.198 10 false 5 V/DIV. 1.417,1.927 2.792,2.125 1.375,0.198 10 false 2 ms./DIV.

Waveform 3

Item Content
Tester Connection A34-19 (DON2) - A34-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Engine running


h.
A112562E13
2.844,1.219 3.156,1.375 0.313,0.156 10 false GND 0.094,0.042 1.177,0.344 1.083,0.302 10 false 5 V/DIV. 1.25,1.99 2.323,2.177 1.073,0.188 10 false 5 ms./DIV.

Waveform 4

Item Content
Tester Connection A34-27 (NOPM)*3 - A34-6 (DGND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition One of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "Oil Pump" being performed