Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
71075B
1.REMOVE BENCH TYPE REAR SEAT CUSHION COVER
Detach the hook.
for Gasoline Model:
for HV Model:
w/ Occupant Detection Sensor:
Disconnect the 3 connectors.
Detach the clamp and claw.
Using a thin-bladed screwdriver, detach the hook to remove the bench type rear seat cushion cover from the rear seat cushion pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the bench type rear seat cushion cover.
Tape the thin-bladed screwdriver tip before use.
87510Q
2.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
87510P
3.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
Use the same procedure described for the LH side.
82194
4.REMOVE REAR SEAT WIRE LH (w/ Occupant Detection Sensor)
Detach the clamp and remove the rear seat wire LH.
82193
5.REMOVE REAR SEAT WIRE RH (w/ Occupant Detection Sensor)
Detach the clamp and remove the rear seat wire RH.
71940A
6.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the 2 rear seat headrest assemblies.
71960B
7.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
Remove the rear center seat headrest assembly.
72668F
8.REMOVE REAR LOWER SEATBACK LOCK BEZEL LH (for LH Side)
|
Remove in this Direction |
Using a moulding remover D, detach the claw.
Pull in the removal direction shown in the illustration to detach the guide and remove the rear lower seatback lock bezel LH.
72667B
9.REMOVE REAR UPPER SEATBACK LOCK BEZEL LH (for LH Side)
|
Remove in this Direction |
|
Protective Tape |
Using a moulding remover D, detach the claw.
Using a thin-bladed screwdriver, detach the claw on the rear side and remove the rear upper seatback lock bezel LH.
Tape the thin-bladed screwdriver tip before use.
71702B
10.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH (for LH Side)
Detach the hook.
Detach the hook.
Pull out the 2 fasteners from the hole of rear seatback board sub-assembly LH.
Open the 2 fasteners.
Remove the clip.
Remove the 2 clips.
| *a | Guide |
| *b | Hook |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Pull in the removal direction (1) shown in the illustration to detach the claw.
Pull in the removal direction (2) shown in the illustration to detach the guide.
Pull in the removal direction (3) shown in the illustration to detach the hook and remove the rear seatback board sub-assembly LH.
11.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Detach the claw and remove the 2 rear seat headrest supports.
Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly LH.
71078S
12.REMOVE SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)
|
Protective Tape |
Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover LH from the separate type rear seatback pad LH as shown in the illustration.
Be careful not to dirty or damage the separate type rear seatback cover.
Tape the thin-bladed screwdriver tip before use.
87510S
13.REMOVE REAR SEATBACK HEATER ASSEMBLY LH (for LH Side, w/ Seat Heater System)
72640A
14.REMOVE REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)
Remove the 2 screws.
Remove the 3 bolts and rear seatback lock assembly LH.
Remove the rear seat lock control lever sub-assembly LH together with the rear seatback lock assembly LH.
72058A
15.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (for LH Side)
Detach the hook and remove the rear seat lock control lever sub-assembly LH from the rear seatback lock assembly LH.
73178A
16.REMOVE SEAT BELT ANCHOR COVER CAP (for RH Side)
|
Remove in this Direction |
Using a moulding remover D, detach the claw.
Pull in the removal direction shown in the illustration to detach the guide.
|
Remove in this Direction |
Detach the guide to remove the seat belt anchor cover cap as shown in the illustration.
73373
17.REMOVE REAR SEAT SHOULDER BELT COVER (for RH Side)
Pass the rear center seat outer belt assembly from the slit and remove the rear seat shoulder belt cover.
72668E
18.REMOVE REAR LOWER SEATBACK LOCK BEZEL RH (for RH Side)
|
Remove in this Direction |
Using a moulding remover D, detach the claw.
Pull in the removal direction shown in the illustration to detach the guide and remove the rear lower seatback lock bezel RH.
72667A
19.REMOVE REAR UPPER SEATBACK LOCK BEZEL RH (for RH Side)
|
Remove in this Direction |
|
Protective Tape |
Using a moulding remover D, detach the claw.
Using a thin-bladed screwdriver, detach the claw on the rear side and remove the rear upper seatback lock bezel RH.
Tape the thin-bladed screwdriver tip before use.
71701B
20.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH (for RH Side)
Detach the hook.
Detach the hook.
Pull out the 2 fasteners from the hole of rear seatback board sub-assembly RH.
Open the 2 fasteners.
Remove the 2 clips.
| *a | Guide |
| *b | Hook |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Pull in the removal direction (1) shown in the illustration to detach the claw.
Pull in the removal direction (2) shown in the illustration to detach the guide.
Pull in the removal direction (3) shown in the illustration to detach the hook and remove the rear seatback board sub-assembly RH.
72868B
21.REMOVE CENTER ARMREST HINGE COVER (for RH Side)
Fold the rear center seat armrest assembly forward.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw on the rear side.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration and detach the claw and guide to remove the center armrest hinge cover.
72830
22.REMOVE REAR CENTER SEAT ARMREST ASSEMBLY (for RH Side)
Remove the bolt and washer.
Return the rear center seat armrest assembly to rotate the outside location pin to the position as shown in the illustration.
| *a | Outside Location Pin | - | - |
|
Rotate | - | - |
| *a | Outside Location Pin |
| *b | Inside Location Pin |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the outside location pin in the removal direction (1) shown in the illustration.
Detach the inside location pin in the removal direction (2) shown in the illustration and remove the rear center seat armrest assembly.
Remove the bush.
23.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Detach the claw and remove the 4 rear seat headrest supports.
Detach the hook.
Pass the rear center seat outer belt assembly through the hole of separate type rear seatback cover with pad.
Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly RH.
71077S
24.REMOVE SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)
|
Protective Tape |
Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover RH from the separate type rear seatback pad RH as shown in the illustration.
Be careful not to dirty or damage the separate type rear seatback cover.
Tape the thin-bladed screwdriver tip before use.
87510R
25.REMOVE REAR SEATBACK HEATER ASSEMBLY RH (for RH Side, w/ Seat Heater System)
73350C
26.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)
72630C
27.REMOVE REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)
Remove the 2 screws.
Remove the 3 bolts and rear seatback lock assembly RH.
Remove the rear seat lock control lever sub-assembly RH together with the rear seatback lock assembly RH.
72057
28.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (for RH Side)
Detach the hook and remove the rear seat lock control lever sub-assembly RH from the rear seatback lock assembly RH.