Home › Vehicle Interior › SEAT › POWER SEAT SWITCH
RM3620E _58 Vehicle Interior _076405 SEAT _0372020 POWER SEAT SWITCH G

SEAT  POWER SEAT SWITCH  INSPECTION  


PROCEDURE

Hide 84922C 1.INSPECT FRONT POWER SEAT SWITCH LH (for LHD)

a.
B526582C01
0.76,1.365 1.01,0.563 true 1.063,1.896 1.26,1.396 true 1.885,1.146 2.146,0.542 true 2.25,1.906 2.417,1.365 true 2.438,3.396 2.813,3.333 true 2.219,3.323 2.771,2.917 true 2.083,3.313 2.552,2.583 true 1.948,3.313 2.031,2.552 true 1.635,3.333 1.063,2.563 true 1.802,3.344 1.51,2.521 true 1.354,3.323 0.615,3.021 true 1.49,3.333 0.781,2.75 true 2.677,4.021 1.969,3.667 true 1.448,4.031 1.479,3.688 true 0.635,3.969 1.031,3.667 true 0.99,0.396 1.302,0.552 0.313,0.156 10 false *a 0.906,1.885 1.219,2.042 0.313,0.156 10 false *b 2.135,0.365 2.448,0.521 0.313,0.156 10 false *c 2.094,1.896 2.406,2.052 0.313,0.156 10 false *d 0.104,2.052 0.417,2.208 0.313,0.156 10 false *e 2.865,3.229 3.354,3.458 0.49,0.229 10 false RCLR 2.813,2.781 3.292,3 0.479,0.219 10 false RCLF 2.49,2.385 3.104,2.583 0.615,0.198 10 false LUP 1.927,2.344 2.542,2.542 0.615,0.198 10 false FUP 1.313,2.333 1.927,2.531 0.615,0.198 10 false FDWN 0.802,2.344 1.271,2.563 0.469,0.219 10 false SLDR 0.406,2.563 0.865,2.781 0.458,0.219 10 false SLDF 0.104,2.896 0.594,3.125 0.49,0.229 10 false LDWN 2.719,3.99 3.333,4.188 0.615,0.198 10 false H 1.406,4.104 2.021,4.302 0.615,0.198 10 false R 0.51,4.042 1.125,4.24 0.615,0.198 10 false E
*a Slide and Front Vertical Switch
*b Slide and Lifter Switch
*c Reclining Switch
*d Lumbar Support Switch
*e Component without harness connected
(Front Power Seat Switch LH)


w/ Memory:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Slide Switch:
Tester Connection Switch Condition Specified Condition
7 (SLDF) - 20 (E) Front position Below 1 Ω
6 (SLDR) - 20 (E) Rear position Below 1 Ω

Front Vertical Switch:
Tester Connection Switch Condition Specified Condition
4 (FUP) - 20 (E) Up position Below 1 Ω
5 (FDWN) - 20 (E) Down position Below 1 Ω

Lifter Switch:
Tester Connection Switch Condition Specified Condition
3 (LUP) - 20 (E) Up position Below 1 Ω
8 (LDWN) - 20 (E) Down position Below 1 Ω

Reclining Switch:
Tester Connection Switch Condition Specified Condition
2 (RCLF) - 20 (E) Front position Below 1 Ω
1 (RCLR) - 20 (E) Rear position Below 1 Ω

Lumbar Support Switch:
Tester Connection Switch Condition Specified Condition
14 (H) - 20 (E) Hold position Below 1 Ω
17 (R) - 20 (E) Release position Below 1 Ω


If the result is not as specified, replace the front power seat switch LH.



b.
B526583C01
0.781,1 1.146,0.427 true 0.969,1.406 1.219,1.135 true 1.833,0.833 2.229,0.26 true 2.927,1.438 2.594,1.01 true 2.281,2.49 2.698,2.333 true 1.083,2.531 0.656,2.427 true 2.073,2.458 2.354,2.104 true 1.885,2.469 1.76,2.094 true 1.333,2.49 1.052,2.104 true 1.073,2.719 0.563,2.833 true 1.344,2.771 0.76,3.052 true 2.26,3.083 1.896,2.771 true 2.656,3.052 2.104,2.76 true 2.927,2.813 2.344,2.74 true 1.833,3.125 1.729,2.781 true 1.417,3.083 1.552,2.781 true 1.104,0.24 1.417,0.396 0.313,0.156 10 false *a 0.802,1.448 1.115,1.604 0.313,0.156 10 false *b 2.208,0.073 2.521,0.229 0.313,0.156 10 false *c 2.896,1.458 3.208,1.615 0.313,0.156 10 false *d 0.031,1.729 0.344,1.885 0.313,0.156 10 false *e 2.781,2.229 3.396,2.427 0.615,0.198 10 false SLDR 2.406,1.875 3.021,2.073 0.615,0.198 10 false R 1.542,1.844 2.156,2.042 0.615,0.198 10 false RCLR 0.813,1.844 1.427,2.042 0.615,0.198 10 false SLDF 0.229,2.26 0.844,2.458 0.615,0.198 10 false RCLF 0.375,2.802 0.625,2.948 0.25,0.146 10 false E 0.521,3.094 0.969,3.292 0.448,0.198 10 false FDWN 1.156,3.135 1.771,3.333 0.615,0.198 10 false LDWN 1.833,3.156 2.042,3.323 0.208,0.167 10 false H 2.25,3.135 2.552,3.313 0.302,0.177 10 false LUP 2.813,3.063 3.135,3.281 0.323,0.219 10 false FUP 3.042,2.75 3.375,2.958 0.333,0.208 10 false B
*a Slide and Front Vertical Switch
*b Slide and Lifter Switch
*c Reclining Switch
*d Lumbar Support Switch
*e Component without harness connected
(Front Power Seat Switch LH)


w/o Memory:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Slide Switch:
Tester Connection Switch Condition Specified Condition
4 (SLDF) - 6 (B) Front position Below 1 Ω
1 (SLDR) - 12 (E)
4 (SLDF) - 12 (E) Neutral Below 1 Ω
1 (SLDR) - 12 (E)
4 (SLDF) - 12 (E) Rear position Below 1 Ω
1 (SLDR) - 6 (B)

Front Vertical Switch:
Tester Connection Switch Condition Specified Condition
7 (FUP) - 6 (B) Up position Below 1 Ω
11 (FDWN) - 12 (E)
7 (FUP) - 12 (E) Neutral Below 1 Ω
11 (FDWN) - 12 (E)
7 (FUP) - 12 (E) Down position Below 1 Ω
11 (FDWN) - 6 (B)

Lifter Switch:
Tester Connection Switch Condition Specified Condition
8 (LUP) - 6 (B) Up position Below 1 Ω
10 (LDWN) - 12 (E)
8 (LUP) - 12 (E) Neutral Below 1 Ω
10 (LDWN) - 12 (E)
8 (LUP) - 12 (E) Down position Below 1 Ω
10 (LDWN) - 6 (B)

Reclining Switch:
Tester Connection Switch Condition Specified Condition
5 (RCLF) - 6 (B) Front position Below 1 Ω
3 (RCLR) - 12 (E)
5 (RCLF) - 12 (E) Neutral Below 1 Ω
3 (RCLR) - 12 (E)
5 (RCLF) - 12 (E) Rear position Below 1 Ω
3 (RCLR) - 6 (B)

Lumbar Support Switch:
Tester Connection Switch Condition Specified Condition
9 (H) - 6 (B) Hold position Below 1 Ω
2 (R) - 12 (E)
9 (H) - 12 (E) Neutral Below 1 Ω
2 (R) - 12 (E)
9 (H) - 12 (E) Release position Below 1 Ω
2 (R) - 6 (B)


If the result is not as specified, replace the front power seat switch LH.



Hide 84922B 2.INSPECT FRONT POWER SEAT SWITCH RH (for RHD)

a.
B509286C03
2.042,1.792 1.656,1.26 true 2.979,1.823 2.677,1.448 true 2.24,1.302 2.635,0.5 true 1.042,1.219 1.49,0.49 true 2.115,3.344 2.948,3.083 true 1.969,3.313 2.844,2.74 true 1.813,3.313 2.417,2.583 true 1.688,3.313 1.917,2.5 true 1.5,3.333 1.417,2.5 true 1.365,3.313 1.083,2.583 true 1.167,3.333 0.583,2.75 true 1.083,3.333 0.5,3.083 true 1.802,4.083 1.927,3.698 true 1,4.094 1.479,3.708 true 2.51,3.99 2.375,3.688 true 2.948,1.875 3.26,2.031 0.313,0.156 10 false *a 2.583,0.302 2.896,0.458 0.313,0.156 10 false *b 2.042,1.854 2.354,2.01 0.313,0.156 10 false *c 1.5,0.333 1.813,0.49 0.313,0.156 10 false *d 0.042,2.031 0.354,2.188 0.313,0.156 10 false *e 2.927,2.875 3.427,3.052 0.5,0.177 10 false LDWN 2.802,2.552 3.417,2.75 0.615,0.198 10 false SLDF 2.302,2.333 2.917,2.531 0.615,0.198 10 false SLDR 1.719,2.219 2.333,2.417 0.615,0.198 10 false FDWN 1.271,2.271 1.583,2.5 0.313,0.229 10 false FUP 0.844,2.354 1.167,2.5 0.323,0.146 10 false LUP 0.302,2.469 0.917,2.667 0.615,0.198 10 false RCLF 0.052,2.833 0.479,3.031 0.427,0.198 10 false RCLR 0.917,4.167 1.24,4.313 0.323,0.146 10 false H 1.75,4.188 2.073,4.333 0.323,0.146 10 false R 2.51,4.104 2.833,4.25 0.323,0.146 10 false E
*a Slide and Front Vertical Switch
*b Slide and Lifter Switch
*c Reclining Switch
*d Lumbar Support Switch
*e Component without harness connected
(Front Power Seat Switch RH)


w/ Memory:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Slide Switch:
Tester Connection Switch Condition Specified Condition
4 (SLDF) - 11 (E) Front position Below 1 Ω
5 (SLDR) - 11 (E) Rear position Below 1 Ω

Front Vertical Switch:
Tester Connection Switch Condition Specified Condition
7 (FUP) - 11 (E) Up position Below 1 Ω
6 (FDWN) - 11 (E) Down position Below 1 Ω

Lifter Switch:
Tester Connection Switch Condition Specified Condition
8 (LUP) - 11 (E) Up position Below 1 Ω
3 (LDWN) - 11 (E) Down position Below 1 Ω

Reclining Switch:
Tester Connection Switch Condition Specified Condition
9 (RCLF) - 11 (E) Front position Below 1 Ω
10 (RCLR) - 11 (E) Rear position Below 1 Ω

Lumbar Support Switch:
Tester Connection Switch Condition Specified Condition
17 (H) - 11 (E) Hold position Below 1 Ω
14 (R) - 11 (E) Release position Below 1 Ω


If the result is not as specified, replace the front power seat switch RH.



b.
B509284C02
2.219,0.99 2.5,0.406 true 1.031,0.875 1.229,0.406 true 2.906,1.531 2.677,1.198 true 1.917,1.531 1.625,0.969 true 1.083,2.542 0.698,2.094 true 1.375,2.458 1.167,2.052 true 1.885,2.479 1.708,2 true 2.083,2.458 2.302,2.031 true 2.344,2.521 2.76,2.198 true 1.083,2.698 0.594,2.906 true 0.865,3.073 1.354,2.771 true 1.292,3.104 1.542,2.781 true 1.688,3.125 1.708,2.781 true 2.208,3.094 1.906,2.781 true 2.646,3.052 2.104,2.781 true 2.76,2.844 2.323,2.729 true 3.031,1.573 3.344,1.729 0.313,0.156 10 false *a 2.448,0.198 2.76,0.354 0.313,0.156 10 false *b 2,1.552 2.313,1.708 0.313,0.156 10 false *c 1.26,0.198 1.573,0.354 0.313,0.156 10 false *d 0,1.646 0.313,1.802 0.313,0.156 10 false *e 2.813,1.969 3.427,2.167 0.615,0.198 10 false RCLF 2.292,1.771 2.906,1.969 0.615,0.198 10 false SLDF 1.51,1.74 2.125,1.938 0.615,0.198 10 false RCLR 1.063,1.771 1.292,1.969 0.229,0.198 10 false R 0.406,1.833 1.021,2.031 0.615,0.198 10 false SLDR 0.417,2.865 0.656,3.031 0.24,0.167 10 false B 0.635,3.135 0.969,3.323 0.333,0.188 10 false FUP 1.042,3.177 1.385,3.396 0.344,0.219 10 false LUP 1.656,3.188 1.854,3.365 0.198,0.177 10 false H 2.042,3.188 2.49,3.354 0.448,0.167 10 false LDWN 2.573,3.135 3.188,3.333 0.615,0.198 10 false FDWN 2.885,2.813 3.115,3.01 0.229,0.198 10 false E
*a Slide and Front Vertical Switch
*b Slide and Lifter Switch
*c Reclining Switch
*d Lumbar Support Switch
*e Component without harness connected
(Front Power Seat Switch RH)


w/o Memory:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Slide Switch:
Tester Connection Switch Condition Specified Condition
2 (SLDF) - 12 (B) Front position Below 1 Ω
5 (SLDR) - 6 (E)
2 (SLDF) - 6 (E) Neutral Below 1 Ω
5 (SLDR) - 6 (E)
2 (SLDF) - 6 (E) Rear position Below 1 Ω
5 (SLDR) - 12 (B)

Front Vertical Switch:
Tester Connection Switch Condition Specified Condition
11 (FUP) - 12 (B) Up position Below 1 Ω
7 (FDWN) - 6 (E)
11 (FUP) - 6 (E) Neutral Below 1 Ω
7 (FDWN) - 6 (E)
11 (FUP) - 6 (E) Down position Below 1 Ω
7 (FDWN) - 12 (B)

Lifter Switch:
Tester Connection Switch Condition Specified Condition
10 (LUP) - 12 (B) Up position Below 1 Ω
8 (LDWN) - 6 (E)
10 (LUP) - 6 (E) Neutral Below 1 Ω
8 (LDWN) - 6 (E)
10 (LUP) - 6 (E) Down position Below 1 Ω
8 (LDWN) - 12 (B)

Reclining Switch:
Tester Connection Switch Condition Specified Condition
1 (RCLF) - 12 (B) Front position Below 1 Ω
3 (RCLR) - 6 (E)
1 (RCLF) - 6 (E) Neutral Below 1 Ω
3 (RCLR) - 6 (E)
1 (RCLF) - 6 (E) Rear position Below 1 Ω
3 (RCLR) - 12 (B)

Lumbar Support Switch:
Tester Connection Switch Condition Specified Condition
9 (H) - 12 (B) Hold position Below 1 Ω
4 (R) - 6 (E)
9 (H) - 6 (E) Neutral Below 1 Ω
4 (R) - 6 (E)
9 (H) - 6 (E) Release position Below 1 Ω
4 (R) - 12 (B)


If the result is not as specified, replace the front power seat switch RH.