Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM3620E _59 Vehicle Exterior _076403 MIRROR (EXT) _0372094 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 87966 1.INSTALL OUTER MIRROR RETRACTOR LH (w/o Foot light)

a.
B541800C01
1.75,1.667 1.75,1.333 false 1.667,1.688 1.979,1.885 0.313,0.198 10 false *a
*a Vinyl Tape


Wind vinyl tape around the harness sub-assembly to secure it.


b.
B540094C01
0,0 0,0 false
V113147

Install in this Direction


Insert a new harness sub-assembly through the frame sub-assembly as shown in the illustration.


c.
B540095C01
2.313,0.604 2.479,0.271 2.479,0.271 2.646,0.271 true 0.229,1.667 0.396,1.667 0.396,1.667 0.563,1.417 true 1.583,1.594 1.667,1.427 1.667,1.427 1.833,1.427 true 0.031,1.594 0.344,1.792 0.313,0.198 10 false *a 1.896,1.354 2.104,1.542 0.208,0.188 10 true *a 2.708,0.198 3.021,0.396 0.313,0.198 10 false *b
*a Guide
*b Harness Clamp
V113147

Install in this Direction


Attach the guide and harness clamp to install the frame sub-assembly as shown in the illustration.


d.
B540096

Install the 2 screws.


e.
B540097

Connect the actuator sub-assembly connector.


f.
B540098

Install the actuator sub-assembly with the 4 screws.


g.
B540091

Using a T25 "TORX" socket wrench, install the base sub-assembly with 3 new "TORX" screws.


h.
B540100C01
0,0 0,0 false
V113147

Install in this Direction


Insert a new harness sub-assembly through the gasket as shown in the illustration.


i.
B540101C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and install a new gasket as shown in the illustration.


j.
B541800C01
1.75,1.667 1.75,1.333 false 1.667,1.688 1.979,1.885 0.313,0.198 10 false *a
*a Vinyl Tape


Remove the vinyl tape.


k.
B540113C01
1.104,2.656 1.604,3.031 1.604,3.031 2.104,2.656 true 1.542,3.063 1.854,3.219 0.313,0.156 10 false *a
*a Marking


Adjust the harness sub-assembly so that the marking is at the position shown in the illustration.


l.
B540114C01
1.417,1.75 1.583,1.75 1.583,1.75 1.833,1.375 true 1.219,1.667 1.531,1.865 0.313,0.198 10 false *a 2.813,1.198 2.969,1.396 0.156,0.198 10 false A
*a Vinyl Tape


Wind vinyl tape as shown in the illustration.

Standard Clearance:
Area Measurement
A 50 mm (1.97 in.)



m.
B541801

Connect each connector to a new adapter.


n.
B541802C01
1,2.583 1.5,2.583 false 0.802,2.469 1.115,2.625 0.313,0.156 10 false *a
*a Wire Harness Routing


Rotate the adapter and twist the longer wire harness as shown in the illustration.


o.
B540102

Connect the connector.


p.
B540103

Attach the rubber cover.


Hide 87948 2.INSTALL OUTER MIRROR HOLE COVER LH

a.
B540099C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and rib to install the outer mirror hole cover LH.

NOTICE:

If the outer mirror retractor has been replaced, replace the outer mirror hole cover LH with a new one.



Hide 86790F 3.INSTALL SIDE TELEVISION CAMERA ASSEMBLY LH (w/ Panoramic View Monitor System)

Hide 4.INSTALL OUTER MIRROR LIGHT BULB (w/ Foot light)

Hide 81740 5.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Hide 8794BA 6.INSTALL NO. 3 OUTER MIRROR COVER LH

Hide 87945 7.INSTALL OUTER MIRROR COVER LH