Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS
RM3620E _59 Vehicle Exterior _076403 MIRROR (EXT) _0372095 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87961 1.INSPECT OUTER MIRROR LH (w/o Blind Spot Monitor System)

a.
B525821C01
1.313,1.125 1.813,1.125 true 1.302,1.583 1.802,1.583 true 0.167,0.073 0.479,0.229 0.313,0.156 10 false *a 1.177,1.063 1.49,1.219 0.313,0.156 10 false 1 1.177,1.521 1.49,1.677 0.313,0.156 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 7.0 to 9.5 Ω


If the result is not as specified, replace the outer mirror LH.



Hide 87931 2.INSPECT OUTER MIRROR RH (w/o Blind Spot Monitor System)

a.
B525823C01
1.667,1.583 2.167,1.583 false 1.667,1.115 2.167,1.115 false 2.26,1.052 2.417,1.25 0.156,0.198 10 false 1 2.26,1.5 2.417,1.698 0.156,0.198 10 false 2 0.354,0.375 0.667,0.573 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 7.0 to 9.5 Ω


If the result is not as specified, replace the outer mirror RH.



Hide 87961 3.INSPECT OUTER MIRROR LH (w/ Blind Spot Monitor System)

a.
B525821C01
1.313,1.125 1.813,1.125 true 1.302,1.583 1.802,1.583 true 0.167,0.073 0.479,0.229 0.313,0.156 10 false *a 1.177,1.063 1.49,1.219 0.313,0.156 10 false 1 1.177,1.521 1.49,1.677 0.313,0.156 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 6.5 to 9.0 Ω


If the result is not as specified, replace the outer mirror LH.



b.

Check the outer rear view mirror indicator operation.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B525822C01
1.083,0.417 1.552,0.417 true 1.844,0.396 2.313,0.396 true 1,0.021 1.313,0.219 0.313,0.198 10 false *a 0.667,0.354 1.125,0.531 0.458,0.177 10 false BSM+ 2.385,0.302 2.844,0.479 0.458,0.177 10 false BSM-
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

NOTICE:
·

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.

·

Do not apply a voltage of more than 6 V.



OK:
Battery Connection Specified Condition
Positive (+) end of the 6 V dry-cell battery → 2 (BSM+)
Negative (-) end of the 6 V dry-cell battery → 1 (BSM-)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.



Hide 87931 4.INSPECT OUTER MIRROR RH (w/ Blind Spot Monitor System)

a.
B525823C01
1.667,1.583 2.167,1.583 false 1.667,1.115 2.167,1.115 false 2.26,1.052 2.417,1.25 0.156,0.198 10 false 1 2.26,1.5 2.417,1.698 0.156,0.198 10 false 2 0.354,0.375 0.667,0.573 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 6.5 to 9.0 Ω


If the result is not as specified, replace the outer mirror RH.



b.

Check the outer rear view mirror indicator operation.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B525824C01
1.885,0.396 2.365,0.396 true 1.042,0.375 1.521,0.375 true 0.938,0.01 1.25,0.208 0.313,0.198 10 false *a 0.635,0.302 1.271,0.5 0.635,0.198 10 false BSM+ 2.396,0.323 2.802,0.531 0.406,0.208 10 false BSM-
*a Component without harness connected
(Outer Mirror RH)


Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

NOTICE:
·

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.

·

Do not apply a voltage of more than 6 V.



OK:
Battery Connection Specified Condition
Positive (+) end of the 6 V dry-cell battery → 2 (BSM+)
Negative (-) end of the 6 V dry-cell battery → 1 (BSM-)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.