Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM3620E _59 Vehicle Exterior _076403 MIRROR (EXT) _0372097 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

a.
B525841C02
1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.833,3 1.25,2.667 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 1.938,3.052 1.938,2.719 true 2.688,1.094 3,1.25 0.313,0.156 10 false *1 2.615,1.469 2.927,1.625 0.313,0.156 10 false *2 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Auto Power Retract Mirror)

a.
B525840C01
2.125,0.75 2.625,0.75 true 1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.833,3 1.25,2.667 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 2.458,3.031 2.292,2.698 true 2.75,3 2.417,2.667 true 0.583,2.5 0.917,2.5 true 1.938,3.052 1.938,2.719 true 2.667,0.677 2.979,0.833 0.313,0.156 10 false *1 2.688,1.094 3,1.25 0.313,0.156 10 false *2 2.615,1.469 2.927,1.625 0.313,0.156 10 false *3 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.385,3.063 2.844,3.26 0.458,0.198 10 false MR 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR 0.458,2.427 0.917,2.625 0.458,0.198 10 false E 2.729,3.052 3.188,3.25 0.458,0.198 10 false MF
*1 Mirror Retract Switch
*2 Mirror Adjust Switch
*3 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (B) - 11 (MF)
9 (E) - 12 (MR)
Return position Below 1 Ω
13 (B) - 11 (MF)
9 (E) - 12 (MR)
Driving position 10 kΩ or higher
9 (E) - 11 (MF) Retract position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Auto Power Retract Mirror)

a.
B525839C01
2.125,0.75 2.625,0.75 true 1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.833,3 1.25,2.667 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 2.458,3.031 2.292,2.698 true 2.75,3 2.417,2.667 true 0.583,2.5 0.917,2.5 true 1.938,3.052 1.938,2.719 true 2.667,0.677 2.979,0.833 0.313,0.156 10 false *1 2.688,1.094 3,1.25 0.313,0.156 10 false *2 2.615,1.469 2.927,1.625 0.313,0.156 10 false *3 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.385,3.063 2.844,3.26 0.458,0.198 10 false MR 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR 0.458,2.427 0.917,2.625 0.458,0.198 10 false E 2.729,3.052 3.188,3.25 0.458,0.198 10 false MAT
*1 Mirror Retract Switch
*2 Mirror Adjust Switch
*3 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11(MAT) - 9(E)
12(MR) - 9(E)
Return position 10 kΩ or higher
11(MAT) - 9(E) AUTO position Below 1 Ω
12(MR) - 9(E) Retract position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.