Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2018.10–2020.08
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) D

TELEMATICS  TELEMATICS SYSTEM(for eCall)  SYSTEM DESCRIPTION  


DESCRIPTION


a.

eCall provides 2 services: Automatic Emergency Call and Manual Emergency Call.

If the vehicle is involved in an accident, the telematics system will make an automatic emergency call to a Public Safety Answering Point (PSAP) and transmit the vehicle location, determined by a GNSS satellite, and vehicle information. After receiving an emergency call from the vehicle, depending on the situation, a PSAP operator may immediately contact emergency services.

Y178726C01
4.802,5.906 5.115,6.104 0.313,0.198 10 false *a 3.271,3.927 3.583,4.125 0.313,0.198 10 false *b 5.635,4.438 5.948,4.635 0.313,0.198 10 false *c 5.344,1.448 5.656,1.646 0.313,0.198 10 false *c 6.719,3.677 7.031,3.875 0.313,0.198 10 false *d 3.906,1.729 4.219,1.927 0.313,0.198 10 false *e 0.458,2.375 0.771,2.573 0.313,0.198 10 false *f 1.271,3.052 1.583,3.25 0.313,0.198 10 false *g 2.354,1.229 2.667,1.427 0.313,0.198 10 false *c 0.646,4.844 0.958,5.042 0.313,0.198 10 false *h 2.198,4.948 2.51,5.146 0.313,0.198 10 false *i 0.344,6.333 0.656,6.531 0.313,0.198 10 false *j
*a Emergency Call Service *b GNSS Satellite
*c Cellular Phone Line *d Cellular Phone Base Station
*e Mobile Network Operator (MNO) or Mobile Virtual Network Operator (MVNO) *f Public Safety Answering Point (PSAP)
*g Public Fixed Line *h Emergency Vehicle
*i Public safety authorities such a police or fire department *j The illustrations shown are examples only and may differ from the actual service.




FUNCTION OF MAIN COMPONENTS


Component Function

*1: w/ Communication Telematics Box

*2: w/o Communication Telematics Box

Map Light Sub-assembly
·

Manual (SOS) Switch


Sends a switch signal to the telephone transceiver assembly when pressed. (When a manual emergency call is performed.)
LED Indicator Light Green
·

Illuminates for 2 seconds after the ignition switch is turned to ON and the manual (SOS) switch indicator (red) has illuminated for 10 seconds.

·

Turns on when the system is operating normally.

·

Blinks during an emergency call.

·

Blinks during test mode.

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (green) blinks at the same time).


Red
·

Illuminates for 10 seconds after the ignition switch is turned to ON.

·

Blinks when an emergency call cannot be performed.

·

Turns off when the system is operating normally.

·

Illuminates when the mobilephone battery needs to be replaced.

·

Illuminates in diagnostic mode to indicate a DTC.

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (red) blinks at the same time).


Communication Telematics Box*1
·

Sends the microphone voice signal to the telephone transceiver assembly.

·

Outputs voice signals received from the telephone transceiver assembly through a built-in speaker.

·

Checks for malfunctions in its built-in speaker and microphone when the ignition switch is turned to ON.

·

Checks for an open in the speaker and microphone circuits between it and the telephone transceiver assembly when the ignition switch is ON.


Telephone Microphone Assembly*2 Sends the microphone voice signal to the telephone transceiver assembly.
Front No. 4 Speaker Assembly*2 Outputs sound signals received from the telephone transceiver assembly through a front No. 4 speaker assembly.
No. 1 Amplifier Antenna Assembly
·

Sends and receives data and voice signals used for emergency calls via a communication network.

·

Receives GNSS radio signals and sends them to the telephone transceiver assembly.


Telephone Transceiver Assembly
·

Uses the No. 1 amplifier antenna assembly to send and receive data and voice signals used for emergency calls via a communication network.

-

Sends the received voice signal to the communication telematics box*1 or front No. 4 speaker assembly.*2

-

Receives the sent voice signal from the communication telematics box*1 or front No. 4 speaker assembly.*2

-

Sends a mute signal to the stereo component amplifier assembly*1 or radio and display receiver assembly*2. (The audio system is automatically muted during an emergency call.)

-

Sends vehicle location information to the PSAP.

-

Conducts self-diagnosis every time the ignition switch is turned to ON and after an automatic emergency call or manual emergency call is made.



Mobilephone Battery
·

When an automatic emergency call is performed and the auxiliary battery is damaged, provides power to the telephone transceiver assembly.

·

When a manual emergency call is made, is not used as the power source.


Airbag Sensor Assembly Sends a collision signal to the telephone transceiver assembly. (An automatic emergency call is made.)


MAYDAY ID OUTLINE


a.

The telephone transceiver assembly functions as the emergency call service device to perform emergency calls.


b.

The telephone transceiver assembly has serial numbers (IMEI, ICCID) which can be used to identify the individual device when servicing.


c.
E405998C01
2.583,1.906 2.75,1.906 2.75,1.906 2.75,0.938 false 2.396,1.802 2.708,2 0.313,0.198 10 false *a
*a IMEI, ICCID


The IMEI and ICCID are printed on the label attached to the telephone transceiver assembly.



COMMUNICATION SYSTEM


a.

CAN Communication Outline

i.

The telematics system uses CAN communication between the telephone transceiver assembly and ECUs.




DIAGNOSTIC FUNCTION OUTLINE


a.

The telematics system has a diagnostic function (the result will be displayed on the GTS).