Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for 2-Pot Caliper)
RM3620E _54 Brake _076409 BRAKE (FRONT) _0372102 FRONT BRAKE(for 2-Pot Caliper) G

BRAKE (FRONT)  FRONT BRAKE(for 2-Pot Caliper)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:

Before performing the inspection, check the shape of the front disc brake cylinder assembly.

C409447C01
0.083,0.083 0.396,0.25 0.313,0.167 10 false *A 3.917,0.083 4.25,0.25 0.333,0.167 10 false *B
*A for Type A *B for Type B



PROCEDURE

Hide 1.INSPECT BRAKE CYLINDER AND PISTON

a.

Check the front disc brake cylinder bore and front disc brake piston for rust and scoring. If necessary, replace the front disc brake cylinder assembly and front disc brake piston.


Hide 2.INSPECT PAD LINING THICKNESS

a.
C405069C01
2.271,0.917 2.417,0.417 2.417,0.417 2.583,0.417 true 2.656,0.313 2.969,0.469 0.313,0.156 10 false *a
*a Ruler


Using a ruler, measure the front disc brake pad lining thickness.

Standard thickness:

12.0 mm (0.472 in.)


Minimum thickness:

1.0 mm (0.0394 in.)


HINT:
·

If a front disc brake pad lining thickness is less than the minimum thickness, replace the front disc brake pads.

·

Be sure to check front disc thickness when replacing the front disc brake pads with new ones.




Hide 3.INSPECT FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Make sure that the front disc brake pad support plates have sufficient rebound, no deformation, cracks or wear, and that all rust and dirt is cleaned off. If necessary, replace the front disc brake pad support plates.


Hide 4.INSPECT DISC THICKNESS

a.
C405070C01
2.75,1.833 2.583,1.833 2.583,1.833 2.417,0.917 false 2.833,1.75 3.146,1.906 0.313,0.156 10 false *a
*a Micrometer


Using a micrometer, measure the front disc thickness.

for Type A:
Standard thickness:

28.0 mm (1.102 in.)

Minimum thickness:

25.0 mm (0.984 in.)


for Type B:
Standard thickness:

34.0 mm (1.339 in.)

Minimum thickness:

31.0 mm (1.220 in.)


HINT:

If the front disc thickness is less than the minimum thickness, replace the front disc.



Hide 5.INSPECT DISC RUNOUT

a.

Inspect the front axle hub bearing looseness and front axle hub runout.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>ON-VEHICLE INSPECTION


b.

Temporarily install the front disc with the 5 hub nuts.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


c.
C405071C01
2.188,0.833 2.75,1.417 2.75,1.417 2.917,1.417 true 3,1.323 3.313,1.479 0.313,0.156 10 false *a
*a Dial Indicator with Magnetic Base


Using a dial indicator with magnetic base, measure the disc runout 10 mm (0.394 in.) from the outer edge of the front disc.

Maximum disc runout:

0.05 mm (0.00197 in.)


NOTICE:

Keep the magnet of the dial indicator away from the front speed sensor.


HINT:

If the runout exceeds the maximum value, change the installation position of the front disc to minimize the runout. If the runout exceeds the maximum even when the installation position is changed, grind the front disc. If the front disc thickness is less than the minimum, replace the front disc.



d.

Remove the 5 hub nuts and front disc.