Home › Vehicle Interior › MIRROR (INT) › DIGITAL REAR-VIEW MIRROR SYSTEM › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076052 MIRROR (INT) _0372136 DIGITAL REAR-VIEW MIRROR SYSTEM D

MIRROR (INT)  DIGITAL REAR-VIEW MIRROR SYSTEM  OPERATION CHECK  


HINT:
·

It is only necessary to perform an inspection when there are dents or distortion in the back door panel sub-assembly as a result of an accident.

·

Inspections are not required when replacing parts or removing and reinstalling.



Camera image range confirmation procedure


a.

Set the vehicle in the position shown in the illustration and create a target on the wall.

NOTICE:
·

Perform on a level surface.

·

Remove all luggage from the vehicle before starting work.

·

Adjust the tire pressures to the specified pressure before starting work.



E401338C02
2.302,0.458 2,0.177 2,0.177 1.771,0.177 true 3.031,0.958 2.906,0.771 2.906,0.771 2.719,0.771 true 3.385,0.729 3.792,0.292 3.792,0.292 4,0.292 true 2.313,2.354 2.01,2.073 2.01,2.073 1.781,2.073 true 3.021,2.458 2.844,2.344 2.844,2.344 2.656,2.344 true 3.385,2.438 3.792,2 3.792,2 4,2 true 0.979,1.052 0.719,0.708 0.719,0.708 0.49,0.708 true 5.51,2.833 5.323,3.094 5.323,3.094 5.135,3.094 true 5.667,2.51 5.885,2.865 5.885,2.865 6.094,2.865 true 0.281,0.635 0.594,0.792 0.313,0.156 10 false *1 4.094,1.927 4.406,2.083 0.313,0.156 10 false *2 2.5,0.708 2.813,0.865 0.313,0.156 10 false *3 1.542,0.094 1.854,0.25 0.313,0.156 10 false *4 2.625,0.135 2.938,0.292 0.313,0.156 10 false *5 4.625,2.896 4.938,3.052 0.313,0.156 10 false *6 5.438,2.052 5.75,2.208 0.313,0.156 10 false *7 6.323,2.406 6.635,2.563 0.313,0.156 10 false *8 2.625,2.021 2.938,2.177 0.313,0.156 10 false *5 1.573,2.01 1.885,2.167 0.313,0.156 10 false *4 2.448,2.281 2.76,2.438 0.313,0.156 10 false *3 4.094,0.208 4.406,0.365 0.313,0.156 10 false *2 4.938,3.031 5.25,3.188 0.313,0.156 10 false *1 6.198,2.781 6.51,2.938 0.313,0.156 10 false *3
*1 Vehicle Center *2 Wall, etc.
*3 Target *4 Vehicle Rear End
*5 100 cm (3.28 ft.) *6 141 cm (4.62 ft.)
*7 49 cm (1.61 ft.) *8 3.6 cm (1.417 in.)



b.
E402892C01
1.885,0.99 2.135,0.813 2.135,0.813 2.313,0.813 true 1.75,1.542 1.49,2.021 1.49,2.021 1.323,2.021 true 0.094,0.073 0.406,0.281 0.313,0.208 10 false *a 2.427,0.75 2.74,0.969 0.313,0.219 10 false *1 1.125,1.927 1.438,2.125 0.313,0.198 10 false *2
*a Inner Rear View Mirror Assembly
*1 Target
*2 Switch Lever


With the ignition switch to ON, operate the switch lever and turn the display on (digital mirror mode) and check that the target is recognized on the inner rear view mirror assembly.

HINT:
·

Set the display settings to the initial settings (position, zoom [enlargement/reduction])

·

If the target is properly displayed, there is no problem with the positioning and the digital inner mirror system is normal.