Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › INTAKE MANIFOLD
RM3620E _51 Engine / Hybrid System _076482 A25A-FXS INTAKE / EXHAUST _0372156 INTAKE MANIFOLD A

A25A-FXS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL VACUUM HOSE

a.

Install the vacuum hose to the intake manifold.


Hide 12611B 2.INSTALL NO. 1 ENGINE COVER

a.

Install the No. 1 engine cover with the clip.


Hide 17177 3.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 4.INSTALL INTAKE MANIFOLD

a.
A433919N01
1.75,0.042 1.906,0.24 0.156,0.198 10 true 1 0.865,0.052 1.021,0.25 0.156,0.198 10 true 2 2.583,0.031 2.74,0.229 0.156,0.198 10 true 3 0.115,0.25 0.271,0.448 0.156,0.198 10 true 4 3.188,0.094 3.344,0.292 0.156,0.198 10 true 5

w/o Stud Bolt:

i.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 5 bolts.


ii.

Tighten the 5 bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



b.
A436576C02
1.708,0.052 1.865,0.25 0.156,0.198 10 true 1 0.854,0.031 1.01,0.229 0.156,0.198 10 true 2 2.563,0.042 2.719,0.24 0.156,0.198 10 true 3 0.135,0.229 0.292,0.427 0.156,0.198 10 true 4 3.208,0.094 3.365,0.292 0.156,0.198 10 true 5
V100135

Bolt
V100136

Nut


w/ Stud Bolt:

i.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 3 bolts and 2 nuts.


ii.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



Hide 23820 5.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.

Connect the No. 2 fuel vapor feed hose to the intake manifold.


Hide 16278 6.INSTALL NO. 2 WATER BY-PASS PIPE

a.
A402290N02
0.844,1.792 0.99,1.958 0.146,0.167 10 true A 2.104,1.969 2.271,2.135 0.167,0.167 10 true B 1.281,0.344 1.438,0.521 0.156,0.177 10 true A

Temporarily install the No. 2 water by-pass pipe to the cylinder block sub-assembly with the bolt (B).


b.

Using an 8 mm socket wrench, temporarily install the No. 2 water by-pass pipe to the intake manifold with the 2 bolts (A).


c.

Tighten the bolt (B).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Using the 8 mm socket wrench, tighten the 2 bolts (A).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Attach the wire harness clamp to connect the HV air conditioning wire.


Hide 16279 7.CONNECT NO. 3 WATER BY-PASS PIPE

a.

Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 82121 8.CONNECT ENGINE WIRE

a.
A433918

Attach the wire harness clamp to connect the engine wire to the intake manifold.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A405766

Connect the engine wire to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the No. 5 engine wire connector.


Hide 25860 9.INSTALL PURGE VALVE (PURGE VSV)

Hide 89421 10.INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 22030 12.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY