Home › Engine / Hybrid System › A25A-FKS (STARTING) › STARTER (w/ Stop And Start System) › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076487 A25A-FKS STARTING _0372221 STARTER(w/ Stop And Start System) A

A25A-FKS STARTING  STARTER(w/ Stop And Start System)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A414118C01
1.563,0.104 1.708,0.104 1.708,0.104 1.906,0.219 false 2.833,0.74 2.885,0.406 2.885,0.406 3.052,0.406 false 2.615,1.677 3,1.677 false 0.531,1.906 0.531,1.604 false 3.021,1.583 3.333,1.74 0.313,0.156 10 false *1 1.385,0.021 1.698,0.177 0.313,0.156 10 false *2 3.073,0.313 3.385,0.469 0.313,0.156 10 false *3 0.448,1.917 0.76,2.073 0.313,0.156 10 false *4
*1 Starter Center Bearing Clutch Sub-assembly
*2 Pinion Drive Lever
*3 Rubber Seal
*4 Starter Drive Housing Assembly
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever as shown in the illustration.


b.

Install the pinion drive lever and rubber seal to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal to the starter drive housing assembly.


Hide 2.INSTALL PLANETARY GEAR

a.
A414119C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter center bearing clutch sub-assembly.


b.

Install the 3 planetary gears to the starter center bearing clutch sub-assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

A347623C02
1.625,0.469 2.26,0.302 2.26,0.302 2.51,0.302 false 1.594,1.979 1.813,1.979 1.813,1.979 2.042,1.625 false 2.552,0.219 2.865,0.375 0.313,0.156 10 false *1 1.438,1.885 1.75,2.042 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


a.

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.



Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A211303

Hold the brush spring back and set the 4 brushes as shown in the illustration.


b.
A211304

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes as shown in the illustration.


c.
A314282C02
1.396,0.219 1.552,0.219 1.552,0.219 2.458,0.771 true 2.51,0.563 2.938,0.156 2.938,0.156 3.073,0.156 true 2.167,1.542 2.302,1.542 2.302,1.542 2.51,0.958 true 1.208,0.104 1.521,0.26 0.313,0.156 10 false *a 3.146,0.063 3.375,0.219 0.229,0.156 10 false *b 1.99,1.438 2.302,1.594 0.313,0.156 10 false *c
*a Grommet
*b Negative (-) Brush Holder Plate
*c Positive (+) Motor Lead Wire


Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.


Hide 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A414120C01
1.844,0.188 2.031,0.188 2.031,0.188 2.323,0.385 false 0.292,1.698 0.469,1.698 0.469,1.698 1.146,0.833 true 1.281,1.927 1.458,1.927 1.458,1.927 2.031,1.188 true 0.125,1.604 0.438,1.76 0.313,0.156 10 false *a 1.115,1.844 1.427,2 0.313,0.156 10 false *b 1.688,0.104 2,0.26 0.313,0.156 10 false *a
*a Lead Wire Rubber
*b Cutout


Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

Align the lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.



b.
A414108

Install the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.
A414121C01
1.656,1.875 1.656,1.521 true 1.969,1.292 2.146,0.823 2.146,0.823 2.344,0.823 true 0.667,1.792 0.854,1.792 0.854,1.792 1.208,1.427 false 2.688,1.198 2.823,0.781 2.823,0.781 3.021,0.781 false 2.646,1.865 2.979,1.781 2.979,1.781 3.125,1.781 true 0.5,1.708 0.813,1.865 0.313,0.156 10 false *1 3.042,0.688 3.354,0.844 0.313,0.156 10 false *a 2.365,0.729 2.677,0.885 0.313,0.156 10 false *b 3.146,1.688 3.385,1.875 0.24,0.188 10 false *c 1.583,1.906 1.896,2.063 0.313,0.156 10 false *b
*1 Starter Yoke Assembly
*a Starter Armature Plate
*b Stopper
*c Protrusion


Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

NOTICE:

Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A414122C01
1.948,0.292 2.365,0.292 false 1.01,0.406 1.229,0.406 1.229,0.406 1.479,0.802 false 2.01,1.938 2.01,1.594 false 2.719,1.865 2.719,1.417 false 0.854,0.323 1.167,0.479 0.313,0.156 10 false *1 1.792,0.208 2.104,0.365 0.313,0.156 10 false *2 1.927,1.958 2.24,2.115 0.313,0.156 10 false *a 2.656,1.885 2.969,2.042 0.313,0.156 10 false *b
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*a Cutout
*b Protrusion


Align the cutout of the starter yoke assembly with the protrusion of the starter drive housing assembly.


b.

Using a T25 "TORX" socket wrench, install the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226B 8.INSTALL REPAIR SERVICE STARTER KIT

a.

Hang the hook of the plunger on the pinion drive lever and install the repair service starter kit.

NOTICE:
·
A432221C01
1.531,0.479 1.698,0.479 1.698,0.479 1.865,0.646 false 1.552,1.635 1.719,1.635 1.719,1.635 1.813,1.458 false 1.365,0.406 1.583,0.594 0.219,0.188 10 false *a 1.375,1.573 1.573,1.76 0.198,0.188 10 false *b
*a Area to be Careful of Pinching
*b Protrusion of Plunger


Make sure the return spring is not resting on the protrusion of the plunger or pushed between the magnet switch and plunger.

·
A414123C01
0.969,2.042 1.135,2.042 1.135,2.042 1.458,1.635 true 2.604,2.052 2.438,2.052 2.438,2.052 2.25,1.885 true 1.802,0.958 2.094,0.469 2.094,0.469 2.281,0.469 true 0.49,4.521 0.688,4.521 0.688,4.521 0.823,3.25 true 2.646,4.177 2.844,4.177 2.844,4.177 3.125,3.875 false 1.698,3.01 1.792,2.542 1.792,2.542 1.927,2.542 false 1.844,3.042 1.917,2.76 1.917,2.76 2.052,2.76 false 1.969,3.125 2.021,2.927 2.021,2.927 2.135,2.927 false 2.5,3.271 2.646,2.896 2.646,2.896 2.781,2.896 false 1.156,3.635 1.333,3.635 1.333,3.635 1.573,3.104 true 0.323,4.427 0.635,4.583 0.313,0.156 10 false *1 2.802,2.802 3.115,2.958 0.313,0.156 10 false *3 2.625,1.958 2.938,2.115 0.313,0.156 10 false *4 0.781,1.958 1.094,2.115 0.313,0.156 10 false *5 2.302,0.375 2.615,0.531 0.313,0.156 10 false *b 0.958,3.542 1.156,3.75 0.198,0.208 10 true *c 0.75,0.521 1.063,0.677 0.313,0.156 10 false *d 1.948,2.458 2.26,2.615 0.313,0.156 10 false *5 2.073,2.656 2.385,2.813 0.313,0.156 10 false *2 2.177,2.833 2.49,2.99 0.313,0.156 10 false *a 2.469,4.083 2.781,4.24 0.313,0.156 10 false *4
*1 Pinion Drive Lever
*2 Plunger
*3 Return Spring
*4 Magnet Switch
*5 Plunger Cover
*a Protrusion
*b Ventilation Hole
*c Hook
*d 90°


Install the plunger cover so that the ventilation hole is positioned as shown in the illustration.




b.

Install the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 28249 9.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

A414124C01
0.25,1.656 1.167,1.656 true 0.083,1.563 0.396,1.719 0.313,0.156 10 false *a
*a Lead Wire


a.

Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

Torque:
7.9 N*m (81 kgf*cm, 70 in.*lbf)


b.

Connect the lead wire to terminal M with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 10.INSTALL HARNESS

A414125

a.

Connect the 2 harness connectors to install the harness.


Hide 11.INSTALL WIRE HARNESS

a.
A414126C01
0.25,0.302 0.5,0.302 false 0.344,0.927 0.594,0.927 false 0.833,0.906 1.083,0.906 false 0.188,0.844 0.5,1 0.313,0.156 10 false *1 0.083,0.198 0.396,0.354 0.313,0.156 10 false *a 1.094,0.813 1.406,0.969 0.313,0.156 10 false *b
*1 Wire Harness
*a Nut
*b Noise Filter Harness


Connect the noise filter harness to the repair service starter kit.


b.

Install the wire harness to the starter assembly with the 2 nuts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)