Home › Drivetrain › EG62 (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE
RM3620E _52 Drivetrain _076270 EG62 MANUAL TRANSMISSION / TRANSAXLE _0371316 TRANSMISSION CONTROL CABLE N

EG62 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

The stopper spring used to prevent improper installation that is included with the shift lever supply part is removed in the transmission control cable assembly adjustment procedure.


PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 33820B 2.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:
·

After the shift lever or the shift control cable is replaced, be sure to adjust the transmission control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to reverse without pulling up the slider shaft, the length of the cable must be adjusted.



a.
C406616C01
1.667,1.708 1.667,1.583 1.667,1.583 2.333,1.583 false 0.833,2.833 1.083,2.833 false 1.667,2.417 1.667,2.25 1.667,2.25 2.333,2.25 false 2.333,3 1.75,3 1.75,3 1.75,2.823 false 0.417,1.583 0.583,1.75 0.167,0.167 10 false *a 2.375,1.521 2.542,1.688 0.167,0.167 10 false *1 0.625,2.75 0.792,2.917 0.167,0.167 10 false *2 0.417,2.25 0.583,2.417 0.167,0.167 10 false *b 2.354,2.177 2.521,2.344 0.167,0.167 10 false *1 2.375,2.917 2.542,3.083 0.167,0.167 10 false *3
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
V113147

Pull Out


Release the lock (lock condition to lock release condition).


b.
C406617C01
2.083,0.813 2.5,0.25 2.5,0.25 2.75,0.25 true 0.5,1.083 1.833,1.083 true 2.771,0.167 2.938,0.333 0.167,0.167 10 true *1 0.313,1 0.479,1.167 0.167,0.167 10 true *a
*1 Select Outer Lever
*a Hole


Align the hole of the select outer lever with the hole in the manual transmission case.


c.
C406618

Insert a bolt into the aligned holes to fix the select outer lever in place.

NOTICE:

In order to avoid case damage, do not push the bolt in forcefully.


HINT:
·

Use a bolt with a diameter of 6 mm (0.236 in.) and a length of at least 36 mm (1.417 in.).

·

Depending on the actual bolt diameter, it may be difficult to insert the bolt. In that case, as there is some variation in actual bolt diameters, use a 6.0 mm (0.236 in.) bolt with a comparatively small diameter.




d.
C406619C01
0,0 0,0 false
V113147

Reverse Direction


Move the shift lever in the reverse direction without pulling up the slider shaft.


e.
C406620C01
1.833,3.198 1.833,3.25 1.833,3.25 2.333,3.25 false 1.667,1.76 1.667,1.656 1.667,1.656 2.333,1.656 false 1.75,2.771 1.75,2.583 1.75,2.583 2.333,2.583 false 0.667,2.208 1.083,2.208 false 0.417,1.583 0.583,1.75 0.167,0.167 10 false *a 0.417,2.583 0.583,2.75 0.167,0.167 10 false *b 2.365,3.167 2.531,3.333 0.167,0.167 10 false *3 2.365,1.563 2.531,1.729 0.167,0.167 10 false *1 2.365,2.5 2.531,2.667 0.167,0.167 10 false *1 0.469,2.135 0.635,2.302 0.167,0.167 10 false *2
*1 Case
*2 Lock Piece
*3 Slider
*a Lock Release Condition
*b Lock Condition
V113147

Push In


While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select control cable.


f.
C406621

Remove the bolt to free the select outer lever.


g.
C406622

Remove the stopper spring used to prevent improper installation from the shift lever assembly.

HINT:

The stopper spring used to prevent improper installation is only included with supply parts.