Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for HV Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370839 PANORAMIC VIEW MONITOR SYSTEM(for HV Model) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for HV Model)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

C402935E01
5.323,2.083 6.698,2.281 1.375,0.198 10 false Parking Assist ECU 3.406,0.635 4.781,0.833 1.375,0.198 10 false BAT 3.396,1.042 4.771,1.24 1.375,0.198 10 false IG1 3.406,1.438 4.781,1.635 1.375,0.198 10 false ESS 0.438,1.031 2.115,1.229 1.677,0.198 10 false from IG1 NO.1 Relay 0.396,0.615 2.073,0.813 1.677,0.198 10 false from Auxiliary Battery 0.667,2.344 2.344,2.542 1.677,0.198 10 false : CAN Communication Line 3.156,0.531 3.448,0.729 0.292,0.198 10 false 4 3.156,0.927 3.448,1.125 0.292,0.198 10 false 9 3.156,1.323 3.448,1.521 0.292,0.198 10 false 6 3.417,1.865 4.792,2.063 1.375,0.198 10 false G68 3.417,2.021 5.271,2.302 1.854,0.281 10 false Steering Sensor 2.146,1.198 3.177,1.396 1.031,0.198 10 false ECU-IG1 NO.2 2.167,0.802 3.208,1.01 1.042,0.208 10 false ECU-DCC NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following procedure.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When "!" mark is displayed on the parking assist ECU after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)
a.
E407124C01
1.49,0.083 1.979,0.375 0.49,0.292 0.865,1.823 1.115,1.823 1.115,1.823 1.333,1.396 true 2.281,1.979 2.031,1.979 2.031,1.979 1.896,1.417 true 2.531,0.427 2.281,0.427 2.281,0.427 1.906,1.031 true 0.115,0.052 0.615,0.292 0.5,0.24 10 false *a 1.594,0.146 1.938,0.354 0.344,0.208 10 false G68 0.552,1.74 0.969,1.938 0.417,0.198 10 false ESS 2.365,1.885 2.823,2.094 0.458,0.208 10 false IG1 2.573,0.344 3.031,0.552 0.458,0.208 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-6 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G68-9 (IG1) - G68-6 (ESS) Power switch on (IG) 11 to 14 V
G68-4 (BAT) - G68-6 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR