Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM3620E _59 Vehicle Exterior _076527 WINDOW / GLASS _0372336 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


a.
B187998C16
0.958,0.219 1.271,0.438 0.313,0.219 2.052,0.219 2.365,0.438 0.313,0.219 2.156,0.25 2.344,0.417 0.188,0.167 10 false I2 1.365,0.24 1.677,0.438 0.313,0.198 10 false *A 1.063,0.25 1.385,0.469 0.323,0.219 10 false J2 2.438,0.25 2.75,0.448 0.313,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the J2*1 or I2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-11 (B) - J2-12 (GND) B - W-B Power supply Ignition switch off 11 to 14 V
J2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-11 (B) - I2-12 (GND) B - W-B Power supply Ignition switch off 11 to 14 V
I2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J2*1 or I2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-15 (DOWN) - J2-12 (GND) W - W-B Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J2-20 (UP) - J2-12 (GND) B - W-B Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-15 (DOWN) - I2-12 (GND) W - W-B Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
I2-20 (UP) - I2-12 (GND) B - W-B Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V


e.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-16 (LIN2) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation
J2-17 (LIN1) - Body ground GR - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-16 (LIN2) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation
I2-17 (LIN1) - Body ground GR - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


a.
B527906E06
1.5,0.156 1.938,0.438 0.438,0.281 1.646,0.208 2.104,0.406 0.458,0.198 10 false J6

Disconnect the J6 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J6-2 (B) - Body ground B - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the J6 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-7 (DOWN) - J6-1 (GND) W - W-B Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J6-10 (UP) - J6-1 (GND) B - W-B Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully opened 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-4 (AUTO) - J6-1 (GND) GR - W-B Power window motor AUTO UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
J6-7 (DOWN) - J6-1 (GND) W - W-B Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
J6-10 (UP) - J6-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-9 (LIN) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B527906E07
1.5,0.156 1.938,0.438 0.438,0.281 1.667,0.208 2.125,0.406 0.458,0.198 10 false I7

Disconnect the I7 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I7-2 (B) - Body ground B - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the I7 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-4 (AUTO) - I7-1 (GND) GR - W-B Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
I7-7 (DOWN) - I7-1 (GND) W - W-B Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
I7-10 (UP) - I7-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-7 (DOWN) - I7-1 (GND) W - W-B Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
I7-10 (UP) - I7-1 (GND) B - W-B Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-9 (LIN) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


a.
B527906E08
1.5,0.156 1.938,0.438 0.438,0.281 1.646,0.208 2.104,0.406 0.458,0.198 10 false L5

Disconnect the L5 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L5-2 (B) - Body ground B - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the L5 rear power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

L5-4 (AUTO) - L5-1 (GND) GR - W-B Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
L5-7 (DOWN) - L5-1 (GND) R - W-B*1
W - W-B*2
Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
L5-10 (UP) - L5-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly LH not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly LH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-9 (LIN) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B527906E09
1.5,0.156 1.938,0.438 0.438,0.281 1.635,0.208 2.094,0.406 0.458,0.198 10 false K5

Disconnect the K5 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K5-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K5-2 (B) - Body ground B - Body ground Power supply Ignition switch off 11 to 14 V


c.

Reconnect the K5 rear power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K5-4 (AUTO) - K5-1 (GND) GR - W-B Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
K5-7 (DOWN) - K5-1 (GND) W - W-B Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
K5-10 (UP) - K5-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly RH not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly RH fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V


e.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K5-9 (LIN) - Body ground BE - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E402359C01
3.458,7.698 3.854,8 0.396,0.302 5.458,3.292 5.875,3.531 0.417,0.24 3.167,3.323 3.583,3.563 0.417,0.24 1.125,3.313 1.542,3.552 0.417,0.24 1.833,4.583 2.25,4.823 0.417,0.24 1.01,6.198 1.427,6.438 0.417,0.24 3.615,6.198 4.031,6.438 0.417,0.24 5.333,4.594 5.75,4.833 0.417,0.24 6.25,6.271 6.667,6.51 0.417,0.24 5.26,6.365 5.677,6.604 0.417,0.24 5.26,6.063 5.677,6.302 0.417,0.24 3.615,5.844 4.031,6.083 0.417,0.24 1.594,1.177 1.833,1.177 true 1.135,2.948 0.927,2.948 0.927,2.948 0.927,2.333 true 1.573,0.615 1.573,0.396 1.573,0.396 1.74,0.396 true 1.594,1.51 1.833,1.51 true 1.594,1.823 1.833,1.823 true 0.646,1.042 0.844,1.042 true 3.719,0.948 3.875,1.146 0.156,0.198 10 false A 3.604,7.76 3.76,7.958 0.156,0.198 10 false A 0.844,1.635 1.156,1.833 0.313,0.198 10 false 4F 0.844,2 1.156,2.198 0.313,0.198 10 false 4L 1.885,1.104 2.344,1.302 0.458,0.198 10 false G43 1.885,1.427 2.344,1.625 0.458,0.198 10 false G44 1.906,1.771 2.365,1.969 0.458,0.198 10 false G45 1.229,2.854 1.729,3.083 0.5,0.229 10 false 4K*A 1.229,3.052 1.729,3.281 0.5,0.229 10 false 4M*B 1.792,0.344 2.25,0.542 0.458,0.198 10 false *1 5.813,1.073 6.125,1.271 0.313,0.198 10 false 4D 5.813,1.719 6.125,1.917 0.313,0.198 10 false 4A 1.177,3.354 1.635,3.552 0.458,0.198 10 false G45 3.219,3.375 3.677,3.573 0.458,0.198 10 false G44 5.531,3.333 5.99,3.531 0.458,0.198 10 false G43 1.927,4.625 2.24,4.823 0.313,0.198 10 false 4A 5.469,4.635 5.781,4.833 0.313,0.198 10 false 4D 1.167,6.25 1.479,6.448 0.313,0.198 10 false 4F 3.729,6.229 4.042,6.427 0.313,0.198 10 false 4N 6.375,6.323 6.688,6.521 0.313,0.198 10 false 4L 5.385,6.104 5.646,6.323 0.26,0.219 10 false 4K 5.385,6.406 5.74,6.563 0.354,0.156 10 false 4M 5.771,6.083 6.229,6.281 0.458,0.198 10 false *A 5.76,6.354 6.219,6.552 0.458,0.198 10 false *B 0.229,0.958 0.844,1.156 0.615,0.198 10 false 4H*A 0.229,1.167 0.844,1.365 0.615,0.198 10 false 4N*B 3.719,5.885 4.031,6.083 0.313,0.198 10 false 4H 4.083,5.875 4.542,6.073 0.458,0.198 10 false *A 4.083,6.208 4.542,6.406 0.458,0.198 10 false *B
*A except LHD, Manual Transaxle *B for LHD, Manual Transaxle
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Measure the voltage and waveform according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: except manual Transaxle

*2: for manual Transaxle

G44-1 (FLCY) - Body ground R - Body ground Front door courtesy light switch assembly LH input Front door courtesy light switch assembly LH open Below 1 V
Front door courtesy light switch assembly LH closed 4.7 to 5.3 V
G45-18 (L2) - Body ground LG - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
Driver door key cylinder off Pulse generation
G45-17 (UL3) - Body ground BE - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
Driver door key cylinder off Pulse generation
4H-25 (LIN2) - Body ground*1 W - Body ground LIN communication line Ignition switch ON Pulse generation
4M-25 (LIN2) - Body ground*2 BE - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G44-6 (FRCY) - Body ground BE - Body ground Front door courtesy light switch assembly RH input Front door courtesy light switch assembly RH open Below 1 V
Front door courtesy light switch assembly RH closed 4.7 to 5.3 V
G45-18 (L2) - Body ground LG - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
Driver door key cylinder off Pulse generation
G45-17 (UL3) - Body ground R - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
Driver door key cylinder off Pulse generation
4H-25 (LIN2) - Body ground W - Body ground LIN communication line Ignition switch ON Pulse generation