Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) J

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned to on (IG), the auxiliary battery voltage is applied to IGSW of the ECM. When the transistor in the MREL circuit operates, current flows from the auxiliary battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A412038E12
1.271,6.531 4.198,6.875 2.927,0.344 10 false Certification ECU (Smart Key ECU Assembly) 1.292,6.354 1.75,6.552 0.458,0.198 10 false G54 0.688,5.906 1.354,6.302 0.667,0.396 10 false Auxiliary Battery 0.552,5.167 1.219,5.375 0.667,0.208 10 false MAIN 1.479,3.115 2.229,3.333 0.75,0.219 10 false IG2 MAIN 3.74,3.802 4.552,4.01 0.813,0.208 10 false IG2 NO. 1 4.698,3.104 5.906,3.375 1.208,0.271 10 false ECU-IG2 NO. 1 0.875,1.417 2.073,1.656 1.198,0.24 10 false EFI-MAIN NO. 1 4.594,0.927 5.802,1.198 1.208,0.271 10 false EFI NO. 1 3.51,2.094 4.813,2.365 1.302,0.271 10 false EFI-MAIN NO. 1 3.615,2.833 4.073,3.146 0.458,0.313 10 false 5 4.375,1.156 4.833,1.469 0.458,0.313 10 false 5 3.604,1.156 4.063,1.469 0.458,0.313 10 false 3 4.396,2.854 4.854,3.167 0.458,0.313 10 false 3 3.604,3.344 4.063,3.656 0.458,0.313 10 false 2 4.396,1.656 4.854,1.969 0.458,0.313 10 false 2 3.615,1.656 4.073,1.969 0.458,0.313 10 false 1 4.385,3.344 4.844,3.656 0.458,0.313 10 false 1 5.104,0.656 5.563,0.969 0.458,0.313 10 false 1 4.698,0.646 5.156,0.958 0.458,0.313 10 false 2 5.677,0.656 6.135,0.969 0.458,0.313 10 false 9 5.604,1.156 6.063,1.469 0.458,0.313 10 false 35 5.594,1.646 6.052,1.958 0.458,0.313 10 false 15 5.667,2.833 6.125,3.146 0.458,0.313 10 false 2 5.604,4.958 6.063,5.271 0.458,0.313 10 false 10 5.875,0.781 6.333,1.094 0.458,0.313 10 false +B 5.896,1.281 6.354,1.594 0.458,0.313 10 false +B2 5.885,1.646 6.344,1.958 0.458,0.313 10 false MREL 6.615,1.76 6.979,2.135 0.365,0.375 10 false IC 5.885,2.833 6.344,3.146 0.458,0.313 10 false IGSW 5.885,5.104 6.344,5.417 0.458,0.313 10 false E1 6.01,6.01 6.469,6.323 0.458,0.313 10 false A24 6.302,6.01 6.76,6.323 0.458,0.313 10 false ECM 2.677,5.875 3.135,6.188 0.458,0.313 10 false 17 2.24,5.896 2.698,6.208 0.458,0.313 10 false IG1D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-10 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
A402428C43
0.198,0.917 0.583,1.146 0.385,0.229 1.344,0.802 1.917,0.25 true 0.219,0.25 0.531,0.448 0.313,0.198 10 false *a 1.979,0.156 2.656,0.458 0.677,0.302 10 false IGSW 0.271,0.958 0.583,1.156 0.313,0.198 10 false A24
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (IGSW) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

6.INSPECT IG2 NO. 1 RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Remove the VVT, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays from the No. 1 engine room relay block and No. 1 junction block assembly.

HINT:

Remove the EFI NO. 1 fuse, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay) - A24-15 (MREL) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A24-9 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A24-35 (+B2) Always Below 1 Ω
2 (EFI-MAIN NO. 1 relay) or A24-15 (MREL) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay), A24-9 (+B) or A24-35 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A436367C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 2.24,0.573 2.552,0.729 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
1 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - EFI-MAIN NO. 1 RELAY)

6.INSPECT IG2 NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)

NG

REPLACE IG2 NO. 1 RELAY

7.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)
a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - A24-2 (IGSW) Always Below 1 Ω
3 (IG2 NO. 1 relay) or A24-2 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)
A436369C01
0.104,0.104 0.417,0.26 0.313,0.156 10 false *1 2.073,1.198 2.385,1.354 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 IG2 NO. 1 Relay


a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG2 NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - IG2 NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)
a.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IG2 NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-17 (IG1D) - 1 (IG2 NO. 1 relay) Always Below 1 Ω
G54-17 (IG1D) or 1 (IG2 NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR