Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P036511  Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground  P036515  Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

The camshaft position sensor (for exhaust camshaft) (EV1 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals. The ECM uses the pulse signals to determine the camshaft angle. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P036511 Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground The camshaft position sensor (for exhaust camshaft) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored SAE Code: P0367
P036515 Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open The camshaft position sensor (for exhaust camshaft) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored SAE Code: P0368

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P034011

MONITOR DESCRIPTION

If the output voltage transmitted by the camshaft position sensor (for exhaust camshaft) remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor (for exhaust camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait for 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P036511 or P036515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A436569E03
0.927,2.094 3.271,2.354 2.344,0.26 10 false C12 0.927,2.25 4.094,2.542 3.167,0.292 10 false Camshaft Position Sensor (for Exhaust Camshaft) 5.688,2.25 6.5,2.427 0.813,0.177 10 false ECM 5.042,2.25 5.854,2.427 0.813,0.177 10 false C45 5.479,0.833 6.292,1.01 0.813,0.177 10 false 1.5 kΩ 5.563,0.26 6.375,0.438 0.813,0.177 10 false 5 V 4.5,0.438 5.313,0.615 0.813,0.177 10 false 113 4.583,0.99 5.396,1.167 0.813,0.177 10 false 91 4.51,1.521 5.323,1.698 0.813,0.177 10 false 114 2.313,0.438 3.125,0.615 0.813,0.177 10 false 3 2.302,0.979 3.115,1.156 0.813,0.177 10 false 1 2.302,1.521 3.115,1.698 0.813,0.177 10 false 2 1.917,0.438 2.729,0.615 0.813,0.177 10 false VC2 1.833,0.979 2.646,1.156 0.813,0.177 10 false VVE+ 1.854,1.51 2.667,1.688 0.813,0.177 10 false VVE- 4.844,0.979 5.656,1.156 0.813,0.177 10 false EV1+ 4.844,1.521 5.656,1.698 0.813,0.177 10 false EV1- 4.854,0.448 5.667,0.625 0.813,0.177 10 false VCE1

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A402448C96
0.26,1.104 0.667,1.354 0.406,0.25 0.76,1.833 1.365,1.458 false 2.76,1.833 2.021,1.458 false 1.74,1.958 1.74,1.469 false 0.208,0.167 0.583,0.438 0.375,0.271 10 false *a 0.344,1.146 0.719,1.417 0.375,0.271 10 false C12 0.354,1.76 1,2.073 0.646,0.313 10 false VVE+ 2.823,1.781 3.198,2.052 0.375,0.271 10 false VC2 1.625,1.979 2.26,2.156 0.635,0.177 10 false VVE-
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C12-3 (VC2) - Body ground Power switch on (IG) 4.5 to 5.5 V
C12-1 (VVE+) - Body ground Power switch on (IG) 3.0 to 5.0 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-3 (VC2) - C12-1 (VVE+) Power switch off 1.425 to 1.575 kΩ
C12-2 (VVE-) - Body ground Power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-1 (VVE+) - C45-91 (EV1+) Always Below 1 Ω
C12-2 (VVE-) - C45-114 (EV1-) Always Below 1 Ω
C12-3 (VC2) - C45-113 (VCE1) Always Below 1 Ω
C12-1 (VVE+) or C45-91 (EV1+) - Body ground and other terminals Always 10 kΩ or higher
C12-2 (VVE-) or C45-114 (EV1-) - Body ground and other terminals Always 10 kΩ or higher
C12-3 (VC2) or C45-113 (VCE1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR