Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P06AB11  Control Module Internal Temperature Sensor "B" Circuit Short to Ground  P06AB15  Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open  


DESCRIPTION

The ECM has a built-in internal temperature sensor which detects the internal temperature of the ECM. The resistance of the thermistor within the ECM internal temperature sensor changes according to the internal temperature of the ECM. The resistance of the thermistor increases as the ECM internal temperature decreases and decreases as the ECM internal temperature increases.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P06AB11 Control Module Internal Temperature Sensor "B" Circuit Short to Ground The ECM internal temperature sensor output voltage is less than 0.22 V for 3 seconds or more (1 trip detection logic). ECM Comes on DTC stored SAE Code: P06AD
P06AB15 Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open The ECM internal temperature sensor output voltage is higher than 4.91 V for 3 seconds or more (1 trip detection logic). ECM Comes on DTC stored SAE Code: P06AE

MONITOR DESCRIPTION

The ECM calculates the internal temperature of the ECM based on the output voltage of the ECM internal temperature sensor. If the output voltage of the ECM internal temperature sensor is not within the normal operating range, the ECM will illuminate the MIL and store a DTC. In this case, the ECM internal temperature sensor may be malfunctioning or there may be an open or short in the sensor circuit.

Example:

When the output voltage of the ECM internal temperature sensor is less than 0.22 V, or more than 4.91 V for 3 seconds or more, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components ECM internal temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P06AB11 or P06AB15.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P06AB11 OR P06AB15)
2.READ OUTPUT DTC (DTC P06AB11 OR P06AB15)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P06AB11 or P06AB15 is output B




A

B